Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM C

1NR-VE ENGINE CONTROL  SFI SYSTEM  P0340  IN. Cam Angle Sensor Signal Malfunction  P0342  IN. Cam Angle Sensor Signal Low  P0343  IN. Cam Angle Sensor Signal High  


DESCRIPTION

The camshaft position sensor for the intake camshaft (VV1 signal) consists of a magnet and MRE (Magneto Resistance Element).

The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration and injection timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 IN. Cam Angle Sensor Signal Malfunction When one of the following conditions is met:
·

No camshaft position sensor signal to the ECM while cranking (2 trip detection logic).

·

No camshaft position sensor signal to the ECM at an engine speed of 600 rpm or higher (1 trip detection logic).

·

A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).


·

Open or short in camshaft position sensor circuit (for intake camshaft)

·

Camshaft position sensor (for intake camshaft)

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored
P0342 IN. Cam Angle Sensor Signal Low The output voltage of the camshaft position sensor is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor circuit (for intake camshaft)

·

Camshaft position sensor (for intake camshaft)

·

ECM


Comes on DTC stored
P0343 IN. Cam Angle Sensor Signal High The output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor circuit (for intake camshaft)

·

Camshaft position sensor (for intake camshaft)

·

ECM


Comes on DTC stored

A357521E01
0.135,0.115 0.823,0.396 0.688,0.281 10 false 5 V/DIV. 3.042,0.833 3.396,1.042 0.354,0.208 10 false GND 3.042,1.604 3.396,1.813 0.354,0.208 10 false GND 1.229,1.917 2.354,2.146 1.125,0.229 10 false 20 msec./DIV. 0.156,0.708 0.552,0.938 0.396,0.229 10 false CH1 0.167,1.51 0.563,1.74 0.396,0.229 10 false CH2

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the camshaft position sensor signal (for intake camshaft), and EV1 stands for the camshaft position sensor signal (for exhaust camshaft).



ECM Terminal Name CH1: Between GIN and EGIN
CH2: Between GEX and EGEX
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / EFI / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.
A359813C06
0.26,2.24 0.656,2.521 0.396,0.281 2.25,3.052 1.896,2.51 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.333,2.302 0.615,2.479 0.281,0.177 10 false C48 2.208,3.104 2.521,3.302 0.313,0.198 10 false VCG
*a Front view of wire harness connector
(to Camshaft Position Sensor (for Intake Camshaft))


Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C48-3 (VCG) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C48-1 (GIN) - C50-80 (GIN) Always Below 1 Ω
C48-2 (EGIN) - C50-102 (EGIN) Always Below 1 Ω
C48-1 (GIN) or C50-80 (GIN) - Body ground Always 10 kΩ or higher
C48-2 (EGIN) or C50-102 (EGIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.
B319222C19
2.146,1.563 2.813,1.792 0.667,0.229 10 false *c 0.469,1.781 0.781,1.979 0.313,0.198 10 false *a 2.656,1.781 2.969,1.979 0.313,0.198 10 false *b
*a OK
*b NG
*c Clearance


Check the camshaft position sensor (for intake camshaft) installation condition.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

6.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NG

8.CHECK ENGINE MECHANICAL SYSTEM
6.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)
a.

Replace the camshaft position sensor (for intake camshaft).

Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.

HINT:

If the engine does not start, replace the ECM.



Result:
Result Proceed to
DTC P0340, P0342 or P0343 is output A
DTC is not output B



A

B

END

8.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.

HINT:

If the engine does not start, replace the ECM.



Result:
Result Proceed to
DTC is not output A
DTC P0340, P0342 or P0343 is output B



A

B

10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C48-3 (VCG) - C50-58 (VCG) Always Below 1 Ω
C48-3 (VCG) or C50-58 (VCG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR