51441
1.REMOVE NO. 1 ENGINE UNDER COVER
2.DRAIN ENGINE COOLANT
23250
3.REMOVE FUEL INJECTOR ASSEMBLY
16267
4.DISCONNECT NO. 3 WATER BY-PASS HOSE
Loosen the clamp and disconnect the No. 3 water by-pass hose.
16281
5.DISCONNECT NO. 4 WATER BY-PASS HOSE
87245X
6.DISCONNECT HEATER WATER HOSE (w/ Heater)
87246X
7.DISCONNECT NO. 2 HEATER WATER HOSE (w/ Heater)
16591A
8.DISCONNECT RADIATOR PIPE RADIATOR HOSE
Loosen the hose clamp and disconnect the radiator pipe radiator hose.
16571C
9.REMOVE NO. 1 RADIATOR HOSE
16507
10.REMOVE RADIATOR PIPE SUB-ASSEMBLY
Disconnect the oxygen sensor connector.
Disengage the 2 harness clamps and disconnect the oxygen sensor wire from the radiator pipe sub-assembly.
Remove the 2 bolts and radiator pipe sub-assembly.
11302
11.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
13540
12.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Set the camshaft timing gear assembly, camshaft timing exhaust gear assembly and crankshaft in the positions (20° ATDC) shown in the illustration.
| *a | Timing Mark | *b | TDC |
Never turn the crankshaft counterclockwise (when viewed from the front of the engine).
| *a | Stopper Plate |
| *b | Plunger |
|
Push |
Push down the stopper plate to release the lock and push in the plunger.
| *a | Stopper Plate |
Pull up the stopper plate with the plunger pushed to the end to lock the plunger.
| *a | Pin |
Insert a pin of 3 mm (0.118 in.) diameter into the hole in the stopper plate.
Remove the 2 nuts and No. 1 chain tensioner assembly.
13562
13.REMOVE NO. 2 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 2 chain vibration damper.
13591
14.REMOVE TIMING CHAIN TENSION ARM
Remove the timing chain tension arm.
13506
15.REMOVE CHAIN SUB-ASSEMBLY
Remove the chain sub-assembly.
13566B
16.REMOVE TIMING CHAIN GUIDE
Remove the 2 bolts and timing chain guide.
13050
17.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
Check the lock of the camshaft timing gear assembly.
| *a | Adhesive Tape Sealing Area |
| *b | Prick a Hole |
| *c | Adhesive Tape |
Clean the VVT oil hole on the intake side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.
Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.
Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure A)
Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.
If air leaks out, reattach adhesive tape.
Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.
Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).
Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.
Turn the camshaft timing gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.
Remove the adhesive tape from the camshaft bearing cap.
13070A
18.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Check the lock of the camshaft timing exhaust gear assembly.
| *a | Adhesive Tape Sealing Area |
| *b | Prick a Hole |
| *c | Adhesive Tape |
Clean the VVT oil hole on the exhaust side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.
Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.
Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure B)
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the hole pricked in procedure B to release the lock pin.
If air leaks out, reattach adhesive tape.
Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.
Using a screwdriver with its tip wrapped with tape, forcibly turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).
Be sure to keep the camshaft timing exhaust gear assembly in the retard direction using a screwdriver. If the camshaft timing exhaust gear assembly is released, it will return to the most advanced position automatically due to force from the spring.
Do not damage the camshaft timing exhaust gear assembly.
Using a screwdriver with its tip wrapped with tape, turn the camshaft timing exhaust gear assembly within its movable range (19 to 21°) 2 or 3 times without turning it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.
Remove the adhesive tape from the camshaft bearing cap.
13070A
19.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
| *a | Do not Remove |
| *b | Hold |
Remove the bolt while holding the hexagonal portion of the No. 2 camshaft, then remove the camshaft timing exhaust gear assembly.
Be sure not to remove the other 4 bolts.
Keep the camshaft timing exhaust gear assembly horizontal while removing it from the No. 2 camshaft.
13050
20.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
| *a | Do not Remove |
| *b | Hold |
Remove the bolt while holding the hexagonal portion of the camshaft, then remove the camshaft timing gear assembly.
Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.
Be sure not to remove the other 4 bolts.
Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.
21.REMOVE CAMSHAFT BEARING CAP
Uniformly loosen and remove the 5 bolts in the order shown in the illustration.
| *1 | No. 1 Camshaft Bearing Cap |
| *2 | No. 2 Camshaft Bearing Cap |
| *3 | No. 3 Camshaft Bearing Cap |
| *4 | No. 4 Camshaft Bearing Cap |
Uniformly loosen and remove the 15 bolts in the order shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.
Arrange the removed parts in the correct order.
13512
22.REMOVE NO. 2 CAMSHAFT
Remove the No. 2 camshaft from the camshaft housing sub-assembly.
13511
23.REMOVE CAMSHAFT
Remove the camshaft from the camshaft housing sub-assembly.
13801
24.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
13750
25.REMOVE VALVE LASH ADJUSTER ASSEMBLY
11103
26.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
Remove the 3 bolts.
| *a | Protective Tape |
Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.
Tape the screwdriver tip before use.
13801
27.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
13750
28.INSPECT VALVE LASH ADJUSTER ASSEMBLY