The stop light switch assembly is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch assembly is remaining on. When the stop light switch assembly remains on during "STOP and GO" driving, the ECM interprets this as a fault in the stop light switch assembly. The ECM will illuminate the MIL and store this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0724 | Stop Lamp Switch Circuit Malfunction | The stop light switch assembly remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) (2 trip detection logic). | ·
Short in stop light switch signal circuit ·
Stop light switch assembly ·
ECM |
Comes on | DTC stored |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Wait 5 seconds.
Enter the following menus: Powertrain / EFI / Trouble Codes [B].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Start the engine [C].
Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / EFI / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Refer to DTC P0504.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>SFI SYSTEM>P0504
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, the Data List item "Stop lamp SW" and "ST1 input flag" can be read.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Data List / Stop lamp SW.
Read the values displayed on the GTS.
| GTS Display | Measurement Item/Range (display) | Normal Condition |
|---|---|---|
| Stop lamp SW | Stop lamp SW: ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the stop light switch assembly installation.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Stop light switch assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
| *a | Brake Pedal Depressed | *b | Brake Pedal Released |
| *c | Front view of wire harness connector
(to ECM) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Brake Pedal Condition | Specified Condition |
|---|---|---|
| A24-48 (STP) - Body ground | Released | Below 1.5 V |
| Depressed | 7.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG