Home › Engine / Hybrid System › 2NR-VE COOLING › RADIATOR › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042282 2NR-VE COOLING _0196242 RADIATOR A

2NR-VE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16400 1.INSTALL RADIATOR ASSEMBLY

a.

Install the fan with motor assembly with the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the 2 grommets into the radiator lower support.


c.

Install the radiator assembly into the vehicle.


d.

Install the cooling fan motor connector and wire harness clamp.


Hide 53205 2.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.

Install the 2 grommets to the upper radiator support sub-assembly.


b.

Install the upper radiator support sub-assembly with the 5 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the clamp to the hood lock control cable.


Hide 32922A 3.INSTALL OIL COOLER OUTLET HOSE (for Automatic Transmission)

a.
A360199C01
1.365,1.156 1.677,1.219 true 2.615,1.135 2.927,1.198 true 2.625,0.792 2.875,0.719 true 1.74,1.146 2.052,1.302 0.313,0.156 10 false *a 2.917,0.615 3.229,0.771 0.313,0.156 10 false *b 2.49,0.26 2.802,0.417 0.313,0.156 10 false *c 1.271,1.49 1.583,1.646 0.313,0.156 10 false *d 3,1.135 3.313,1.292 0.313,0.156 10 false *a 1.229,0.271 1.542,0.427 0.313,0.156 10 false *c 2.521,1.479 2.833,1.635 0.313,0.156 10 false *d
*a White Paint Mark
*b Green Paint Mark
*c Upper Side
*d 60°


Install a new oil cooler outlet hose with the 2 clips as shown in the illustration.


Hide 32921D 4.INSTALL OIL COOLER INLET HOSE (for Automatic Transmission)

a.
A360198C01
0.656,0.99 0.938,1.104 true 2.833,1 3.115,1.115 true 2.813,0.667 3.083,0.542 true 0.969,1.01 1.281,1.167 0.313,0.156 10 false *a 3.125,1.063 3.365,1.219 0.24,0.156 10 false *a 3.125,0.438 3.354,0.594 0.229,0.156 10 false *b 0.531,0.146 0.844,0.302 0.313,0.156 10 false *c 0.573,1.333 0.885,1.49 0.313,0.156 10 false *d 2.698,0.125 3.01,0.281 0.313,0.156 10 false *c 2.729,1.323 3.042,1.479 0.313,0.156 10 false *d
*a Yellow Paint Mark
*b Pink Paint Mark
*c Upper Side
*d 60°


Install a new oil cooler inlet hose with the 2 clips as shown in the illustration.


Hide 16572D 5.CONNECT NO. 2 RADIATOR HOSE

a.
A360197C01
1.938,1.198 2.177,1.396 2.177,1.396 2.302,1.396 true 2.313,1.313 2.625,1.469 0.313,0.156 10 false *a 1.802,0.406 2.115,0.563 0.313,0.156 10 false *b
*a Paint Mark
*b Upper Side


Connect the No. 2 radiator hose with the clip as shown in the illustration.


Hide 16571C 6.INSTALL NO. 1 RADIATOR HOSE

a.
A360200C01
0.708,0.667 0.917,0.49 0.917,0.49 1.073,0.49 true 2.74,1.146 2.979,0.927 2.979,0.927 3.094,0.927 true 1.135,0.406 1.365,0.563 0.229,0.156 10 false *a 0.583,0.156 0.896,0.313 0.313,0.156 10 false *b 1.229,0.76 1.542,0.917 0.313,0.156 10 false *c 2.615,0.635 2.927,0.792 0.313,0.156 10 false *b 3.135,0.844 3.354,1 0.219,0.156 10 false *a
*a Paint Mark
*b Upper Side
*c RH Side


Connect the No. 1 radiator hose with the 2 clips as shown in the illustration.


Hide 88460 7.CONNECT COOLER CONDENSER ASSEMBLY

a.
A360189N01
2.281,0.01 2.74,0.208 0.458,0.198 10 true 4, (A) 2.115,1.979 2.333,2.177 0.219,0.198 10 true 1 0.76,1.938 0.885,2.125 0.125,0.188 10 true 3 0.771,0.031 0.896,0.219 0.125,0.188 10 true 2

Temporarily tighten the cooler condenser assembly with the bolt A.


b.

Fully tighten the cooler condenser assembly with the 4 bolts in the order shown in the illustration.


Hide 88561L 8.INSTALL LOWER AIR INLET GRILLE

Hide 88561J 10.INSTALL UPPER AIR INLET GRILLE (except Tropic)

Hide 53629 11.INSTALL HOOD LOCK CONTROL CABLE COVER (for Tropic)

Hide 17750A 12.INSTALL AIR CLEANER INLET ASSEMBLY

Hide 16470 13.INSTALL RADIATOR RESERVE TANK ASSEMBLY

a.

Install the radiator reserve tank assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the radiator reserve tank hose.


Hide 52119A 14.INSTALL FRONT BUMPER COVER

Hide 16.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 17.INSPECT FOR COOLANT LEAK

Hide 18.INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK (for Automatic Transmission)

Hide 51441 19.INSTALL NO. 1 ENGINE UNDER COVER

Hide 20.INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEVEL (for Automatic Transmission)