The main body ECU (fuse block assembly) detects the condition of the door courtesy light switches.
The main body ECU (fuse block assembly) receives door courtesy light switch signals to control the illuminated entry system.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Body Electrical / Body / Data List.
Read the Data List according to the display on the GTS or Techstream.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Driver door courtesy SW | Courtesy light switch (for driver side) signal | ON or OFF | ON: Driver side door open
OFF: Driver side door closed |
- |
| Passenger courtesy SW | Courtesy light switch (for front passenger side) signal | ON or OFF | ON: Front passenger side door open
OFF: Front passenger side door closed |
- |
| RH rear courtesy SW* | Courtesy light switch (for rear RH side) signal | ON or OFF | ON: Rear RH side door open
OFF: Rear RH side door closed |
- |
| LH rear courtesy SW* | Courtesy light switch (for rear LH side) signal | ON or OFF | ON: Rear LH side door open
OFF: Rear LH side door closed |
- |
| Back door courtesy SW | Back door courtesy light switch signal | ON or OFF | ON: Back door open
OFF: Back door closed |
- |
*: w/ Rear Door Courtesy Light Switch
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| NG (for driver side) | A |
| NG (for front passenger side) | B |
| NG (for rear RH side) | C |
| NG (for rear LH side) | D |
| NG (for back door) | E |
| OK | F |
A
B
C
D
E
F
Remove the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3L main body ECU (fuse block assembly) connector.
Disconnect the J19*1 or J20*2 courtesy light switch connector.
*1: for RHD
*2: for LHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-13 - J19-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-13 - J20-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-13 or J19-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-13 or J20-1 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for RHD) | A |
| OK (for LHD) | B |
| NG | C |
A
B
C
Remove the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3L main body ECU (fuse block assembly) connector.
Disconnect the J20*1 or J19*2 courtesy light switch connector.
*1: for RHD
*2: for LHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-14 - J20-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-14 - J19-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-14 or J20-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-14 or J19-1 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for RHD) | A |
| OK (for LHD) | B |
| NG | C |
A
B
C
Remove the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3L main body ECU (fuse block assembly) connector.
Disconnect the J21 courtesy light switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-6 - J21-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3L-6 or J21-1 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for RHD) | A |
| OK (for LHD) | B |
| NG | C |
A
B
C
Remove the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the courtesy light switch.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3K main body ECU (fuse block assembly) connector.
Disconnect the J22 courtesy light switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3K-6 - J22-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3K-6 or J22-1 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for RHD) | A |
| OK (for LHD) | B |
| NG | C |
A
B
C
Remove the back door lock assembly (back door courtesy light switch).
Inspect the back door lock assembly (back door courtesy light switch).
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
Inspect the door courtesy switch only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3K main body ECU (fuse block assembly) connector.
Disconnect the L4 back door lock assembly (back door courtesy light switch).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3K-5 - L4-4 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3K-5 or L4-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L4 back door lock assembly (back door courtesy light switch).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-3 - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for RHD) | A |
| OK (for LHD) | B |
| NG | C |
A
B
C