Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015248 WINDOW DEFOGGER SYSTEM J

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  Rear Window Defogger System does not Operate  


DESCRIPTION

When the rear window defogger switch assembly is pressed, the operation signal is transmitted to the main body ECU (fuse block assembly). When the main body ECU (fuse block assembly) receives the signal, it turns on the rear window defogger.

WIRING DIAGRAM

E322675E01
1.74,1.188 3.365,1.802 1.625,0.615 10 false Back Door Glass (Window Defogger Wire) 1.771,3.094 3.208,3.885 1.438,0.792 10 false Rear Window Defogger Switch Assembly 4.177,3.51 7.156,4.25 2.979,0.74 10 false Main Body ECU (Fuse Block Assembly) 4.802,1.052 5.552,1.344 0.75,0.292 10 false DEF 1.667,0.865 1.896,1.052 0.229,0.188 10 false O1 3.167,0.875 3.396,1.063 0.229,0.188 10 false N1 3.927,0.865 4.156,1.052 0.229,0.188 10 false 3L 3.906,2.49 4.135,2.677 0.229,0.188 10 false 3J 3.927,0.656 4.156,0.844 0.229,0.188 10 false 17 3.938,2.271 4.167,2.458 0.229,0.188 10 false 1 3.208,0.656 3.438,0.844 0.229,0.188 10 false 1 1.708,0.656 1.938,0.844 0.229,0.188 10 false 1 3.219,2.365 3.438,2.563 0.219,0.198 10 false 3 1.656,2.365 1.885,2.552 0.229,0.188 10 false 4 6.042,0.885 6.792,1.177 0.75,0.292 10 false DEFO 6.031,2.49 6.781,2.781 0.75,0.292 10 false DEFSW 3.042,2.365 3.26,2.563 0.219,0.198 10 false L 1.833,2.375 2.063,2.563 0.229,0.188 10 false E 1.781,2.917 2.01,3.104 0.229,0.188 10 false E7

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the battery voltage becomes low, rear window defogger operation is canceled to prioritize supplying power to the power steering system.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (DEFOGGER RELAY)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Active Test.


e.

According to the display on the GTS or Techstream, perform the Active Test.

Body Electrical / Body / Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger relay Rear window defogger wire ON/OFF -

OK:

The window defogger system operates normally.


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - REAR WINDOW DEFOGGER SWITCH ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BACK DOOR GLASS (WINDOW DEFOGGER WIRE))
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - REAR WINDOW DEFOGGER SWITCH ASSEMBLY)
a.

Disconnect the 3J main body ECU (fuse block assembly) connector.


b.

Disconnect the E7 rear window defogger switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3J-1 - E7-3 (L) Always Below 1 Ω
E7-4 (E) - Body ground Always Below 1 Ω
3J-1 or E7-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK REAR WINDOW DEFOGGER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK REAR WINDOW DEFOGGER SWITCH ASSEMBLY
a.

Remove the rear window defogger switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL


b.

Inspect the rear window defogger switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION


Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPLACE REAR WINDOW DEFOGGER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BACK DOOR GLASS (WINDOW DEFOGGER WIRE))
a.

Disconnect the 3L main body ECU (fuse block assembly) connector.


b.

Disconnect the N1 back door glass (window defogger wire) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3L-17 - N1-1 Always Below 1 Ω
3L-17 or N1-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK BACK DOOR GLASS (WINDOW DEFOGGER WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BACK DOOR GLASS (WINDOW DEFOGGER WIRE)
a.

Inspect the back door glass (window defogger wire).

Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER WIRE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (WINDOW DEFOGGER WIRE) - BODY GROUND)

NG

REPAIR BACK DOOR GLASS (WINDOW DEFOGGER WIRE)

6.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (WINDOW DEFOGGER WIRE) - BODY GROUND)
a.

Disconnect the O1 back door glass (window defogger wire) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR