The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller (camshaft timing sprocket assembly). The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0014 | EX. DVVT System Advance Malfunction | Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic). | ·
Valve timing ·
Camshaft timing oil control valve assembly (for exhaust camshaft) ·
Camshaft timing oil control valve filter ·
Camshaft timing exhaust gear assembly ·
ECM |
Comes on | DTC stored |
| P0015 | EX. DVVT System Retard Malfunction | Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic). | ·
Valve timing ·
Camshaft timing oil control valve assembly (for exhaust camshaft) ·
Camshaft timing oil control valve filter ·
Camshaft timing exhaust gear assembly ·
ECM |
Comes on | DTC stored |
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS or Techstream on [A].
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 3 minutes or more [D].
Enter the following menus: Powertrain / EFI / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Depress the accelerator pedal by a large amount.
Idle the engine for 3 minutes or more [G].
Enter the following menus: Powertrain / EFI / Trouble Codes [H].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Refer to DTC P0013.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>P0013
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0014 or P0015 is output | A |
| DTC P0014 or P0015 and other DTCs are output | B |
A
B
Connect the GTS or Techstream to the DLC3.
Start the engine.
Turn the GTS or Techstream on.
Turn the A/C switch on.
Enter the following menus: Powertrain / EFI / Active Test / EX.DVVT Linear.
Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the GTS or Techstream.
| GTS or Techstream Operation | Specified Condition |
|---|---|
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
Refer to "Data List / Active Test" [EX.DVVT OCV duty learning value and EX.DVVT actual angle].
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0014 or P0015 is output | B |
DTC P0014 or P0015 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.
A
B
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft).
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the cylinder head cover sub-assembly.
Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
| *a | Timing Mark | *b | No. 1 Cylinder at TDC Compression |
If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the camshaft timing exhaust gear assembly.
Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CAMSHAFT>REMOVAL
DTC P0014 or P0015 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the oil control valve filter.
Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
Check that the filter is not clogged.
Filter is not clogged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0014 or P0015 is output | B |
DTC P0014 or P0015 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.
A
B