Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0724  Stop Lamp Switch Circuit Malfunction  


DESCRIPTION

The stop light switch assembly is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch assembly is remaining on. When the stop light switch assembly remains on during "STOP and GO" driving, the ECM interprets this as a fault in the stop light switch assembly. The ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0724 Stop Lamp Switch Circuit Malfunction The stop light switch assembly remains on even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.65 mph] or more) (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A199312E33
1.417,2.021 1.823,2.25 0.406,0.229 10 false Idling 0.615,2.354 1.885,2.677 1.271,0.323 10 false Ignition Switch ON 2.521,2.49 2.719,2.688 0.198,0.198 10 false [A] 2.583,3.083 3.292,3.229 0.708,0.146 10 false 5 seconds 3.271,3.49 3.479,3.667 0.208,0.177 10 false [B] 3.458,1.917 3.667,2.094 0.208,0.177 10 false [C] 6.75,3.479 6.948,3.677 0.198,0.198 10 false [E] 4.042,1.5 4.25,1.677 0.208,0.177 10 false [D] 1.24,1.198 1.833,1.385 0.594,0.188 10 false 30 km/h 1.333,1.729 1.875,1.906 0.542,0.177 10 false 3 km/h

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Start the engine [C].

10.

Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / EFI / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Using the GTS or Techstream, the Data List item "Stop lamp SW" and "ST1 input flag" can be read.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DATA LIST / ACTIVE TEST

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (STOP LAMP SW)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / Stop lamp SW.


e.

Read the values displayed on the GTS or Techstream.

OK:
GTS or Techstream Display Measurement Item/Range (display) Normal Condition
Stop lamp SW Stop lamp SW status: ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released





Result:
Proceed to
OK
NG



OK

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

Stop light switch assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK TERMINAL VOLTAGE (STP VOLTAGE)
a.

Disconnect the ECM connector.

A361578C05
4.083,0.75 4.49,1 0.406,0.25 5.802,1.552 5.573,1.073 true 0.615,0.167 0.927,0.365 0.313,0.198 10 false *a 2.26,0.156 2.573,0.354 0.313,0.198 10 false *b 4.385,0.167 4.698,0.365 0.313,0.198 10 false *c 5.844,1.49 6.198,1.688 0.354,0.198 10 false STP 4.156,0.792 4.615,0.99 0.458,0.198 10 false A24
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A24-48 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - ECM)