Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.08–2016.09
RM19Y0E _58 Vehicle Interior _003008 METER / GAUGE / DISPLAY _0015206 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM using the CAN communication system. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM

E324172E01
0.427,1.448 2.615,1.708 2.188,0.26 10 false : CAN Communication Line 1.573,1.125 2.24,1.542 0.667,0.417 10 false ECM 4.51,1.135 6.698,1.521 2.188,0.385 10 false Combination Meter Assembly

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B




A

2.PERFORM ACTIVE TEST USING GTS or TECHSTREAM (TACHOMETER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS or TECHSTREAM (TACHOMETER OPERATION)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Tachometer Tachometer 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 -

OK:

Tachometer indication is normal.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS or TECHSTREAM (ENGINE SPEED)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS or TECHSTREAM (ENGINE SPEED)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Meter / Data List.


e.

According to the display on the GTS or Techstream, read the Data List.

Body Electrical > Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine RPM Engine speed Min.: 0 rpm, Max.: 12750 rpm 550 to 650 rpm (for Manual Transmission):
650 to 750 rpm (for Automatic Transmission):
Idling with warm engine, shift lever in N, A/C off
-

OK:

Engine speed displayed on the GTS or Techstream is approximately the same as the actual engine speed.


Result:
Result
OK
NG




OK

4.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK FOR DTC
a.

Check if SFI system DTCs are output.



Result:
Result Proceed to
DTCs are not output. A
DTCs are output (for 1NR-VE). B
DTCs are output (for 2NR-VE (w/ Air Fuel Ratio Sensor)). C
DTCs are output (for 2NR-VE (w/o Air Fuel Ratio Sensor)). D



A

5.READ VALUE USING GTS or TECHSTREAM (ENGINE SPEED)

B

C

D

5.READ VALUE USING GTS or TECHSTREAM (ENGINE SPEED)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus:

i.

for EFI: Powertrain / EFI / Data List.


ii.

for Meter: Body Electrical / Meter / Data List.



e.

Check the values by referring to the table below.

i.

EFI

Powertrain > EFI > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine revolution speed Engine speed Min.: 0 rpm
Max.: 16383.7 rpm
550 to 650 rpm (for Manual Transmission):
650 to 750 rpm (for Automatic Transmission):
Idling with warm engine, shift lever in N, A/C off
When the crankshaft position sensor is malfunctioning, "Engine revolution speed" is approximately 0 rpm or varies greatly from the actual engine speed.


ii.

Meter

Body Electrical > Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine RPM Engine speed Min.: 0 rpm
Max.: 12750 rpm
550 to 650 rpm (for Manual Transmission):
650 to 750 rpm (for Automatic Transmission):
Idling with warm engine, shift lever in N, A/C off
-



Result:
Result Proceed to
The data list values of the ECUs do not match. A
The data list values of the ECUs match (for 1NR-VE). B
The data list values of the ECUs match (for 2NR-VE). C


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.




A

6.REPLACE COMBINATION METER ASSEMBLY

B

C

6.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

OK:

The operation of the tachometer returns to normal.



Result:
Result Proceed to
OK A
NG (for 1NR-VE) B
NG (for 2NR-VE) C



A

END

B

C