Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0200/21  Front Speed Sensor RH Circuit  C0205/22  Front Speed Sensor LH Circuit  C1235/25  Foreign Object is Attached on Tip of Front Speed Sensor RH  C1236/26  Foreign Object is Attached on Tip of Front Speed Sensor LH  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for the anti-lock brake system. Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn. Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.

C248680E02
1.417,1.219 1.635,1.219 1.635,1.219 1.635,1.458 false 1.5,0.396 1.875,0.396 1.875,0.396 1.875,0.906 false 6.333,1.323 6.948,1.75 0.615,0.427 10 1.4 V 6.333,1.688 6.875,2.031 0.542,0.344 10 0.7 V 4.281,2.188 5.219,2.625 0.938,0.438 10 Low Speed 5.24,2.167 6.292,2.688 1.052,0.521 10 High Speed 4.083,0.302 6.063,0.802 1.979,0.5 10 Waveform (Reference): 0.177,0.292 1.698,0.75 1.521,0.458 10 Front Speed Sensor 0.104,1.115 1.615,1.573 1.51,0.458 10 Speed Sensor Rotor 4.083,0.656 7.125,1.281 3.042,0.625 10 Between Speed Sensor (-) and Body Ground


HINT:

Measure the connection status between the sensor connector and the vehicle wire harness.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C0200/21 Front Speed Sensor RH Circuit
1.

When abnormality has been detected in the wheel speed sensor.

2.

When abnormality has been detected with the wheel speed sensor current and voltage values for a certain period of time.


·

ECU-IG1 fuse

·

Front speed sensor

·

Speed sensor circuit

·

Speed sensor rotor (Front axle hub bearing)

·

Front speed sensor installation

·

Skid control ECU (Brake actuator assembly)


-
C0205/22 Front Speed Sensor LH Circuit
1.

When abnormality has been detected in the wheel speed sensor.

2.

When abnormality has been detected with the wheel speed sensor current and voltage values for a certain period of time.


·

ECU-IG1 fuse

·

Front speed sensor

·

Speed sensor circuit

·

Speed sensor rotor (Front axle hub bearing)

·

Front speed sensor installation

·

Skid control ECU (Brake actuator assembly)


-
C1235/25 Foreign Object is Attached on Tip of Front Speed Sensor RH
1.

System abnormal status continues for a certain period of time.

2.

When a noise has occurred on the wheel speed sensor.

3.

Difference between the maximum wheel speed and minimum wheel speed remains more than the threshold value for a certain period of time.

4.

While the vehicle has accelerated to a certain speed, the corresponding wheel speed is equal to or lower than the threshold value.


·

ECU-IG1 fuse

·

Front speed sensor

·

Speed sensor circuit

·

Front speed sensor installation

·

Skid control ECU (Brake actuator assembly)


-
C1236/26 Foreign Object is Attached on Tip of Front Speed Sensor LH
1.

System abnormal status continues for a certain period of time.

2.

When a noise has occurred on the wheel speed sensor.

3.

Difference between the maximum wheel speed and minimum wheel speed remains more than the threshold value for a certain period of time.

4.

While the vehicle has accelerated to a certain speed, the corresponding wheel speed is equal to or lower than the threshold value.


·

ECU-IG1 fuse

·

Front speed sensor

·

Speed sensor circuit

·

Front speed sensor installation

·

Skid control ECU (Brake actuator assembly)


-

HINT:
·

DTCs C0200/21 and C1235/25 are for the front speed sensor RH.

·

DTCs C0205/22 and C1236/26 are for the front speed sensor LH.



WIRING DIAGRAM

C274050E03
0.333,0.604 2.167,0.802 1.833,0.198 10 false from IG1 Relay 2.958,0.781 3.552,1 0.594,0.219 10 false ECU-IG1 0.406,1.094 0.896,1.292 0.49,0.198 10 false A32 0.427,1.958 0.885,2.156 0.458,0.198 10 false A31 0.406,1.313 1.271,1.75 0.865,0.438 10 false Front Speed Sensor RH 0.417,2.177 1.271,2.656 0.854,0.479 10 false Front Speed Sensor LH 5.167,2.885 5.625,3.083 0.458,0.198 10 false A13 5.156,3.083 6.75,3.531 1.594,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 2.063,1.25 2.365,1.458 0.302,0.208 10 false + 2.073,2.177 2.229,2.365 0.156,0.188 10 false + 2.083,1.542 2.24,1.74 0.156,0.198 10 false - 2.083,2.458 2.24,2.656 0.156,0.198 10 false - 5.25,0.521 5.646,0.719 0.396,0.198 10 false 12 5.25,1.146 5.563,1.344 0.313,0.198 10 false 18 5.25,1.448 5.552,1.75 0.302,0.302 10 false 17 5.25,2.073 5.563,2.323 0.313,0.25 10 false 31 5.25,2.375 5.563,2.573 0.313,0.198 10 false 30 5.5,0.615 5.958,0.813 0.458,0.198 10 false +IG 5.5,1.25 5.958,1.448 0.458,0.198 10 false FL1 5.5,1.542 5.958,1.74 0.458,0.198 10 false FL0 5.5,2.167 5.958,2.365 0.458,0.198 10 false FR1 5.5,2.479 5.958,2.677 0.458,0.198 10 false FR0 5.896,1.979 6.51,2.177 0.615,0.198 10 false GND1 5.885,2.302 6.5,2.5 0.615,0.198 10 false GND2 6.365,1.875 6.677,2.073 0.313,0.198 10 false 25 6.365,2.188 6.677,2.385 0.313,0.198 10 false 1 2.271,1.156 2.49,1.354 0.219,0.198 10 false 1 2.271,2.073 2.49,2.302 0.219,0.229 10 false 1 2.271,1.448 2.458,1.688 0.188,0.24 10 false 2 2.271,2.385 2.458,2.635 0.188,0.25 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the GTS or Techstream to the DLC3.


c.

Turn the GTS or Techstream on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS or Techstream, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel speed FR Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Wheel speed FL Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS or Techstream and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value displayed on the GTS or Techstream is the same as the a speed indicated on the speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.CHECK FRONT SPEED SENSOR INSTALLATION
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC not output. A
DTC output. B


NOTICE:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

9.REPLACE FRONT SPEED SENSOR
3.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C108871C01
0.698,1.365 0.958,1.76 false 0.104,0.094 0.479,0.438 0.375,0.344 10 *1 1.031,1.781 1.406,2.125 0.375,0.344 10 *a 0.427,1.708 0.802,2.052 0.375,0.344 10 *b 2.719,1.833 3.094,2.177 0.375,0.344 10 *c
*1 Front Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Turn the ignition switch off.


b.

Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

4.INSPECT SPEED SENSOR TIP

NG

4.INSPECT SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.



HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.



Result:
Proceed to
OK
NG



OK

5.INSPECT SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

5.INSPECT SPEED SENSOR ROTOR
a.

Replace the front axle hub bearing (front speed sensor rotor).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL

HINT:
·

The front speed sensor rotor is incorporated into the front axle hub bearing.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub bearing.



Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE SPEED SENSOR ROTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A32*1 or A31*2 front speed sensor connector.

*1: for RH

*2: for LH



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open)(for RH):
Tester Connection Condition Specified Condition
A13-31 (FR1) - A31-1 (+) Always Below 1 Ω
A13-30 (FR0) - A31-2 (-) Always Below 1 Ω


Standard Resistance (Check for Open)(for LH):
Tester Connection Condition Specified Condition
A13-18 (FL1) - A32-1 (+) Always Below 1 Ω
A13-17 (FL0) - A32-2 (-) Always Below 1 Ω


Standard Resistance (Check for Short)(for RH):
Tester Connection Condition Specified Condition
A13-31 (FR1) - Body ground Always 10 kΩ or higher
A13-30 (FR0) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short)(for LH):
Tester Connection Condition Specified Condition
A13-18 (FL1) - Body ground Always 10 kΩ or higher
A13-17 (FL0) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

7.CHECK TERMINAL VOLTAGE (+IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (+IG TERMINAL)
a.

Turn the ignition switch off.


b.
C330019C30
1.333,0.167 1.75,0.417 0.417,0.25 2.583,0.438 2.24,1 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.417,0.208 1.875,0.406 0.458,0.198 10 false A13 2.615,0.302 3.073,0.5 0.458,0.198 10 false +IG
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-12 (+IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω
A13-1 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

9.REPLACE FRONT SPEED SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC output. A
DTC not output. B




A

11.REPLACE SPEED SENSOR ROTOR

B

END

11.REPLACE SPEED SENSOR ROTOR
a.

Replace the front axle hub bearing (front speed sensor rotor).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL

HINT:
·

The front speed sensor rotor is incorporated into the front axle hub bearing.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub bearing.



Result:
Proceed to
NEXT




NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC output. A
DTC not output. B




A

B

END