Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1249/39  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting open circuits in the stop light input line of the stop light LH and RH circuits or an open in the ground line with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1249/39 Open in Stop Light Switch Circuit When the stop light switch input voltage shows a certain value.
·

Stop light switch circuit

·

Stop light LH and RH circuits

·

Main body ECU (Fuse block assembly)

·

Skid control ECU (Brake actuator assembly)


-

WIRING DIAGRAM

C332707E03
0.594,1.188 1.208,1.385 0.615,0.198 10 false STPL 1.823,1.708 2.167,1.938 0.344,0.229 10 false 3E 1.844,0.458 2.188,0.688 0.344,0.229 10 false 25 5.99,0.688 6.604,0.885 0.615,0.198 10 false STP 5.74,0.563 6.01,0.76 0.271,0.198 10 false 35 6,2.698 6.615,2.896 0.615,0.198 10 false GND1 6.01,3.292 6.625,3.49 0.615,0.198 10 false GND2 5.396,3.875 7.052,4.281 1.656,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.406,3.688 5.729,3.917 0.323,0.229 10 false A13 5.708,2.552 5.948,2.76 0.24,0.208 10 false 25 5.792,3.156 6.063,3.354 0.271,0.198 10 false 1 0.365,3.792 1.75,4.24 1.385,0.448 10 false Main Body ECU (Fuse Block Assembly) 0.573,1.719 1.188,1.917 0.615,0.198 10 false STPH 1.813,1.167 2.156,1.396 0.344,0.229 10 false 3E 1.823,0.677 2.167,0.906 0.344,0.229 10 false 3C 1.833,0.938 2.177,1.167 0.344,0.229 10 false 10 1.833,1.49 2.177,1.719 0.344,0.229 10 false 18 3.354,1.052 3.698,1.281 0.344,0.229 10 false 2 3.344,1.594 3.688,1.823 0.344,0.229 10 false 1 3.594,1.719 3.938,1.948 0.344,0.229 10 false + 3.594,1.156 3.938,1.385 0.344,0.229 10 false - 2.969,2.125 4.792,2.365 1.823,0.24 10 false Stop Light Switch Assembly 2.979,1.958 3.323,2.188 0.344,0.229 10 false E69

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (STOP SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop SW Stop light switch signal ON or OFF ON: Stop light switch on
OFF: Stop light switch off
-

OK:

The GTS displays ON or OFF according to brake pedal operation.


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS (STOP LIGHT SW)

NG

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)

2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop lamp SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC C1249 is not output. A
DTC C1249 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the 3C main body ECU (fuse block assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A13-35 (STP) - 3C-25 Always Below 1 Ω


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A13-35 (STP) - Body ground Always 10 kΩ or higher
3C-25 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT MAIN BODY ECU (FUSE BLOCK ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the 3E main body ECU (fuse block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
3C-25 - 3E-10 Always Below 1 Ω


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
3C-25 - Body ground Always 10 kΩ or higher
3E-10 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

6.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Always Below 1 Ω
A13-1 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR