Home › Drivetrain › A4R AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM19Y0E _52 Drivetrain _041457 A4R AUTOMATIC TRANSMISSION / TRANSAXLE _0192556 AUTOMATIC TRANSMISSION SYSTEM C

A4R AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0748  Shift Solenoid "A" Electrical  P0778  Shift Solenoid "B" Electrical  P0798  Shift Solenoid "C" Electrical  


DESCRIPTION

Shifting from 1st to 4th is performed in combination with ON and OFF operation of the shift solenoid valves SL1, SL2, SL3, SL, SLU and SLT which is controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Fail-safe function).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Memory Note
P0748 Shift Solenoid "A" Electrical 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

During energization of shift solenoid valve SL1.

2.

An open or short in the shift solenoid valve SL1 circuit is detected.

3.

1 seconds

4.

1-trip detection logic


·

Open or short in shift solenoid valve SL1 circuit

·

Transmission wire (shift solenoid valve SL1)

·

Shift solenoid valve SL1 (transmission valve body assembly)

·

ECM


Come on Blinks DTC stored -
P0778 Shift Solenoid "B" Electrical 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

During energization of shift solenoid valve SL2.

2.

An open or short in the shift solenoid valve SL2 circuit is detected.

3.

1 seconds

4.

1-trip detection logic


·

Open or short in shift solenoid valve SL2 circuit

·

Transmission wire (shift solenoid valve SL2)

·

Shift solenoid valve SL2 (transmission valve body assembly)

·

ECM


Come on Blinks DTC stored -
P0798 Shift Solenoid "C" Electrical 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

During energization of shift solenoid valve SL3.

2.

An open or short in the shift solenoid valve SL3 circuit is detected.

3.

1 seconds

4.

1-trip detection logic


·

Open or short in shift solenoid valve SL3 circuit

·

Transmission wire (shift solenoid valve SL3)

·

Shift solenoid valve SL3 (transmission valve body assembly)

·

ECM


Come on Blinks DTC stored -

·

MIL:"Comes on" means the MIL (Malfunction Indicator Light) illuminates.

·

Memory:"DTC stored" means the ECM stores the trouble code if the ECU detects the DTC detection condition.


WIRING DIAGRAM

C313579E03
0.625,4.427 1.083,4.625 0.458,0.198 10 false C50 0.979,4.427 1.438,4.625 0.458,0.198 10 false ECM 1.25,0.552 1.708,0.75 0.458,0.198 10 false B1+ 1.25,0.802 1.708,1 0.458,0.198 10 false B1- 1.26,1.781 1.719,1.979 0.458,0.198 10 false C2+ 1.26,2.021 1.719,2.219 0.458,0.198 10 false C2- 1.26,3.125 1.719,3.323 0.458,0.198 10 false C3+ 1.26,3.385 1.719,3.583 0.458,0.198 10 false C3- 1.677,0.469 2,0.667 0.323,0.198 10 false 24 1.667,0.719 2,1 0.333,0.281 10 false 25 1.667,1.677 2,1.917 0.333,0.24 10 false 26 1.667,1.927 2.083,2.167 0.417,0.24 10 false 27 1.667,3.031 2,3.25 0.333,0.219 10 false 28 1.667,3.302 2,3.5 0.333,0.198 10 false 29 2.917,0.469 3.229,0.667 0.313,0.198 10 false 13 2.979,0.719 3.292,0.917 0.313,0.198 10 false 6 2.917,1.677 3.25,1.875 0.333,0.198 10 false 12 2.99,1.927 3.323,2.125 0.333,0.198 10 false 5 2.917,3.021 3.25,3.219 0.333,0.198 10 false 11 2.99,3.302 3.323,3.5 0.333,0.198 10 false 4 3.198,0.469 3.51,0.667 0.313,0.198 10 false H7 3.198,0.708 3.51,0.906 0.313,0.198 10 false H1 3.198,1.667 3.51,1.865 0.313,0.198 10 false H8 3.198,1.927 3.51,2.125 0.313,0.198 10 false H2 3.198,3.021 3.51,3.219 0.313,0.198 10 false H9 3.198,3.302 3.51,3.5 0.313,0.198 10 false H3 5.167,0.698 7.01,1 1.844,0.302 10 false Shift Solenoid Valve SL1 5.167,1.917 7.01,2.219 1.844,0.302 10 false Shift Solenoid Valve SL2 5.156,3.281 7,3.583 1.844,0.302 10 false Shift Solenoid Valve SL3 3.177,3.823 4.438,4.073 1.26,0.25 10 false Transmission Wire 3.125,4.385 3.583,4.583 0.458,0.198 10 false C45 3.5,4.385 5.99,4.708 2.49,0.323 10 false Automatic Transmission Assembly

PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / A/T / Trouble Codes.

Powertrain > A/T > Trouble Codes
50001 565
HINT:

When not using the GTS or Techstream, refer to DTC CHECK / CLEAR.

Click hereDrivetrain>A4R AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR



e.

Read the DTC using the GTS or Techstream.

Result:
Display (DTC Output) Proceed to
DTC P0748 is output A
DTC P0778 is output B
DTC P0798 is output C




A

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SL1) - SHIFT SOLENOID VALVE SL1)

B

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SL2) - SHIFT SOLENOID VALVE SL2)

C

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SL3) - SHIFT SOLENOID VALVE SL3)
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SL1) - SHIFT SOLENOID VALVE SL1)
C314053C11
1.01,0.313 1.396,0.313 1.396,0.313 1.688,1.073 true 1.333,1.969 1.594,1.969 1.594,1.969 1.729,1.385 true 0.031,0.042 0.344,0.24 0.313,0.198 10 false *a 0.792,0.24 1.208,0.438 0.417,0.198 10 false H1 1.135,1.885 1.51,2.135 0.375,0.25 10 false H7
*a Component without harness connected
(Transmission Wire)


a.

Disconnect the C45 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (H7) - 6 (H1) 20°C (68°F) 5.0 to 5.6 Ω
13 (H7) - Body ground Always 10 kΩ or higher
6 (H1) - Body ground Always 10 kΩ or higher



c.

Reconnect the C45 transmission wire connector.

Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.INSPECT SHIFT SOLENOID VALVE SL1
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C45 transmission wire connector.


b.

Disconnect the C50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C45-13 (H7) - C50-24 (B1+) Always Below 1 Ω
C45-6 (H1) - C50-25 (B1-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C45-13 (H7) or C50-24 (B1+) - Body ground and other terminals Always 10 kΩ or higher
C45-6 (H1) or C50-25 (B1-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the C50 ECM connector.


e.

Reconnect the C45 transmission wire connector.


Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SHIFT SOLENOID VALVE SL1
C313379C03
0.708,0.531 0.885,0.531 0.885,0.531 1.5,0.896 true 0.708,2.667 0.885,2.667 0.885,2.667 1.5,3.031 true 2.625,0.521 2.458,0.521 2.458,0.521 1.833,0.896 true 2.615,2.667 2.448,2.667 2.448,2.667 1.823,3.042 true 0.094,0.135 0.406,0.292 0.313,0.156 10 false *a 0.583,2.594 0.938,2.865 0.354,0.271 10 false 2 0.583,0.479 0.938,0.75 0.354,0.271 10 false 2 2.75,0.448 3.104,0.719 0.354,0.271 10 false 1 2.698,2.604 3.052,2.875 0.354,0.271 10 false 1 1.177,4.24 1.531,4.51 0.354,0.271 10 false (+) 2.094,4.24 2.448,4.51 0.354,0.271 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL1)


a.

Remove the shift solenoid valve SL1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

NOTICE:
·

Never directly apply battery voltage to the solenoid valve connector (Do not allow a current of 1 A or more to flow). Perform the operation check via the specified bulb (resistance).

·

If a current of 1 A or more flows, the characteristic of the solenoid valve changes.



OK:

The solenoid valve makes an operating sound.


Result:
proceed to
OK
NG




OK

NG

REPLACE SHIFT SOLENOID VALVE SL1 (TRANSMISSION VALVE BODY ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SL2) - SHIFT SOLENOID VALVE SL2)
C314053C12
1.177,0.313 1.563,0.313 1.563,0.313 1.854,1.073 true 1.188,1.854 1.469,1.854 1.469,1.854 1.833,1.406 true 0.031,0.042 0.344,0.24 0.313,0.198 10 false *a 0.99,1.792 1.74,2.052 0.75,0.26 10 false H8 0.948,0.24 1.385,0.469 0.438,0.229 10 false H2
*a Component without harness connected
(Transmission Wire)


a.

Disconnect the C45 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (H8) - 5 (H2) 20°C (68°F) 5.1 to 5.5 Ω
12 (H8) - Body ground Always 10 kΩ or higher
5 (H2) - Body ground Always 10 kΩ or higher



c.

Reconnect the C45 transmission wire connector.

Result:
proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

7.INSPECT SHIFT SOLENOID VALVE SL2
6.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C45 transmission wire connector.


b.

Disconnect the C50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C45-12 (H8) - C50-26 (C2+) Always Below 1 Ω
C45-5 (H2) - C50-27 (C2-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C45-12 (H8) or C50-26 (C2+) - Body ground and other terminals Always 10 kΩ or higher
C45-5 (H2) or C50-27 (C2-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the C50 ECM connector.


e.

Reconnect the C45 transmission wire connector.


Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT SHIFT SOLENOID VALVE SL2
D105552C03
1.188,0.688 1.521,0.927 true 2.021,0.698 1.729,0.927 true 1.229,2.844 1.563,3.083 true 2.052,2.844 1.76,3.073 true 0.125,0.104 0.458,0.438 0.333,0.333 10 *a 1.042,0.552 1.375,0.885 0.333,0.333 10 1 2.094,0.594 2.427,0.927 0.333,0.333 10 2 1.292,3.719 1.625,4.052 0.333,0.333 10 (-) 2.021,3.708 2.354,4.042 0.333,0.333 10 (+) 1.104,2.677 1.438,3.01 0.333,0.333 10 1 2.094,2.688 2.427,3.021 0.333,0.333 10 2 2.677,3.469 3.271,3.865 0.594,0.396 10 21W
*a Component without harness connected
(Shift Solenoid Valve SL2)


a.

Remove the shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.1 to 5.5 Ω



c.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

NOTICE:
·

Never directly apply battery voltage to the solenoid valve connector (Do not allow a current of 1 A or more to flow). Perform the operation check via the specified bulb (resistance).

·

If a current of 1 A or more flows, the characteristic of the solenoid valve changes.



OK:

The solenoid valve makes an operating sound.


Result:
proceed to
OK
NG




OK

NG

REPLACE SHIFT SOLENOID VALVE SL2 (TRANSMISSION VALVE BODY ASSEMBLY)

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SL3) - SHIFT SOLENOID VALVE SL3)
C314053C13
1.302,1.927 1.625,1.927 1.625,1.927 2.01,1.406 true 1.583,0.26 1.865,0.26 1.865,0.26 2.01,1.083 true 0.031,0.042 0.344,0.24 0.313,0.198 10 false *a 1.073,1.865 1.49,2.083 0.417,0.219 10 false H9 1.365,0.198 1.958,0.479 0.594,0.281 10 false H3
*a Component without harness connected
(Transmission Wire)


a.

Disconnect the C45 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (H9) - 4 (H3) 20°C (68°F) 5.1 to 5.5 Ω
11 (H9) - Body ground Always 10 kΩ or higher
4 (H3) - Body ground Always 10 kΩ or higher



c.

Reconnect the C45 transmission wire connector.

Result:
proceed to
OK
NG




OK

9.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

10.INSPECT SHIFT SOLENOID VALVE SL3
9.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C45 transmission wire connector.


b.

Disconnect the C50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C45-11 (H9) - C50-28 (C3+) Always Below 1 Ω
C45-4 (H3) - C50-29 (C3-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C45-11 (H9) or C50-28 (C3+) - Body ground and other terminals Always 10 kΩ or higher
C45-4 (H3) or C50-29 (C3-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the C50 ECM connector.


e.

Reconnect the C45 transmission wire connector.


Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT SHIFT SOLENOID VALVE SL3
C313379C03
0.708,0.531 0.885,0.531 0.885,0.531 1.5,0.896 true 0.708,2.667 0.885,2.667 0.885,2.667 1.5,3.031 true 2.625,0.521 2.458,0.521 2.458,0.521 1.833,0.896 true 2.615,2.667 2.448,2.667 2.448,2.667 1.823,3.042 true 0.094,0.135 0.406,0.292 0.313,0.156 10 false *a 0.583,2.594 0.938,2.865 0.354,0.271 10 false 2 0.583,0.479 0.938,0.75 0.354,0.271 10 false 2 2.75,0.448 3.104,0.719 0.354,0.271 10 false 1 2.698,2.604 3.052,2.875 0.354,0.271 10 false 1 1.177,4.24 1.531,4.51 0.354,0.271 10 false (+) 2.094,4.24 2.448,4.51 0.354,0.271 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL3)


a.

Remove the shift solenoid valve SL3.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.1 to 5.5 Ω



c.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

NOTICE:
·

Never directly apply battery voltage to the solenoid valve connector (Do not allow a current of 1 A or more to flow). Perform the operation check via the specified bulb (resistance).

·

If a current of 1 A or more flows, the characteristic of the solenoid valve changes.



OK:

The solenoid valve makes an operating sound.


Result:
proceed to
OK
NG




OK

NG

REPLACE SHIFT SOLENOID VALVE SL3 (TRANSMISSION VALVE BODY ASSEMBLY)