Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0420  Catalyst System Efficiency Below Threshold  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the No. 2 oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the No. 2 oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the No. 2 oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stores the DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor

·

No. 2 oxygen sensor

·

Exhaust manifold converter sub-assembly (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)


Comes on DTC stored

CATALYST LOCATION

A364757C01
2,0.667 1.833,0.667 1.833,0.667 1.25,1.25 true 2,1.167 1.75,1.167 1.75,1.167 1.25,1.583 true 2.25,1.333 2.083,1.333 2.083,1.333 1.917,1.917 true 0.417,2.083 0.667,2.083 0.667,2.083 0.667,1.167 true 2.833,2.5 2.5,2.5 2.5,2.5 2.5,2 true 3.917,2.167 3.5,2.167 3.5,2.167 3.25,1.75 true 5.833,1.5 5.333,1.5 5.333,1.5 4.75,1.083 true 2,0.583 2.25,0.833 0.25,0.25 10 false *1 2.25,1.271 2.448,1.5 0.198,0.229 10 false *2 0.24,2 0.5,2.229 0.26,0.229 10 false *3 2.021,1.083 2.25,1.281 0.229,0.198 10 false *4 2.938,2.417 3.167,2.615 0.229,0.198 10 false *5 3.938,2.083 4.167,2.281 0.229,0.198 10 false *6 5.833,1.417 6.042,1.615 0.208,0.198 10 false *7
*1 Air Fuel Ratio Sensor *2 No. 2 Oxygen Sensor
*3 Exhaust Manifold *4 TWC: Front Catalyst
*5 Front Exhaust Pipe Assembly *6 TWC: Rear Catalyst
*7 Exhaust Tail Pipe Assembly - -


NOTICE:

Replace the exhaust manifold converter sub-assembly (*3) and the front exhaust pipe assembly (*4) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor*1 and No. 2 oxygen sensor*2)


CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283969E73
1.927,0.313 1.719,0.313 1.719,0.313 1.323,0.875 false 0.74,1.083 1.469,1.24 0.729,0.156 10 false 60 km/h 0.833,2.156 1.208,2.313 0.375,0.156 10 false Idling 0.146,2.406 1.51,2.563 1.365,0.156 10 false Ignition Switch off 1.479,2.646 2.094,3.01 0.615,0.365 10 false Warming up 2.333,2.646 3.135,3.042 0.802,0.396 10 false 10 minutes or more 4.135,2.646 4.896,3 0.76,0.354 10 false 10 minutes or more 1.969,0.25 3.521,0.427 1.552,0.177 10 false Between 95 to 105 km/h 1.667,2.042 1.896,2.219 0.229,0.177 10 false [A] 2.604,0.958 2.927,1.135 0.323,0.177 10 false [B]* 3.146,3.104 3.375,3.281 0.229,0.177 10 false [C] 6.76,3.104 6.99,3.281 0.229,0.177 10 false [H] 3.469,2.031 3.677,2.208 0.208,0.177 10 false [D] 6.198,0.563 6.552,0.74 0.354,0.177 10 false [G]* 4.354,0.938 4.719,1.115 0.365,0.177 10 false [E]* 5.01,3.115 5.208,3.292 0.198,0.177 10 false [F] 3.396,2.646 4.052,3.083 0.656,0.438 10 false Warming up 5.896,2.688 6.615,3.063 0.719,0.375 10 false 10 minutes or more 0.24,3.302 5.917,3.531 5.677,0.229 10 false *: Drive the vehicle while keeping the engine load as constant as possible

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS or Techstream on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS or Techstream on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


9.

Turn the ignition switch off and wait for at least 30 seconds [C].

10.

Turn the ignition switch to ON and turn the GTS or Techstream on.

11.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

12.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


13.

Enter the following menus: Powertrain / EFI / Trouble Codes [F].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

Drive the vehicle at a speed between 95 and 105 km/h (59 and 65 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


16.

Enter the following menus: Powertrain / EFI / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and No. 2 oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A283816E01
5.281,3.365 4.865,3.365 4.865,3.365 4.865,3.125 false 5.167,3.365 5.167,3.115 false 0.583,0.667 1.5,0.896 0.917,0.229 10 Engine Speed 0.854,1.021 1.5,1.25 0.646,0.229 10 3000 rpm 0.854,1.573 1.5,1.802 0.646,0.229 10 2000 rpm 1.115,2.521 1.5,2.74 0.385,0.219 10 Idling 0.365,2.75 1.531,2.948 1.167,0.198 10 Ignition Switch off 2.104,3.167 2.938,3.396 0.833,0.229 10 Warming up 3.417,3.167 4.615,3.396 1.198,0.229 10 At least 3 minutes 5.333,3.281 6.01,3.49 0.677,0.208 10 2 seconds 4.833,3.406 5.313,3.635 0.479,0.229 10 Check 6.646,2.76 7.01,2.99 0.365,0.229 10 Time 1.646,2.656 1.885,2.885 0.24,0.229 10 (a) 2.125,2.427 2.375,2.646 0.25,0.219 10 (b) 3.677,0.885 3.906,1.115 0.229,0.229 10 (c) 4.792,0.885 5.021,1.125 0.229,0.24 10 (d) 5.104,1.458 5.354,1.708 0.25,0.25 10 (d)

(a) Connect the GTS or Techstream to the DLC3.

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm for 2 seconds, and then 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and No. 2 oxygen sensors using the GTS or Techstream.


HINT:
·

If the voltage output of either the air fuel ratio or No. 2 oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume Active Test using the GTS or Techstream.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the No. 2 oxygen sensor (located behind the Three-way Catalytic Converter [TWC]) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A195037E15
0.083,0.042 3.917,0.25 3.833,0.208 10 false Voltage output when active air fuel ratio control not performed: 2.5,0.458 3.542,0.667 1.042,0.208 10 false Normal Catalyst 4.802,0.448 6.156,0.646 1.354,0.198 10 false Deteriorated Catalyst 0.094,1.927 1.271,2.646 1.177,0.719 10 false Waveform of No. 2 Oxygen Sensor behind Three-way Catalytic Converter 0.083,0.542 1.385,1.219 1.302,0.677 10 false Waveform of Air Fuel Ratio Sensor in front of Three-way Catalytic Converter 1.469,0.771 1.844,0.958 0.375,0.188 10 false 3.4 V 1.469,1.125 1.865,1.333 0.396,0.208 10 false 3.1 V 1.479,2.073 1.865,2.281 0.385,0.208 10 false 1.0 V 1.573,2.74 1.865,2.969 0.292,0.229 10 false 0 V 2.635,3.094 3.396,3.302 0.76,0.208 10 false 10 seconds 5.125,3.094 5.896,3.313 0.771,0.219 10 false 10 seconds


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC P0420 is output A
DTC P0420 and other DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (CONTROL THE INJECTION VOLUME)

B

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (CONTROL THE INJECTION VOLUME)
a.

Connect the GTS or Techstream to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS or Techstream on.


d.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / EFI / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2.


f.

Perform the Active Test operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and No. 2 oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS or Techstream.

HINT:
·

The Control the Injection Volume operation lowers the fuel injector volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS or Techstream Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(No. 2 oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status AFS Voltage B1S1 Status O2S B1S2 Actual air fuel ratio, air fuel ratio sensor and No. 2 oxygen sensor condition Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean No. 2 oxygen sensor malfunction -
·

No. 2 oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich No. 2 oxygen sensor malfunction -
·

No. 2 oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system




Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the No. 2 oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the air fuel ratio sensor and No. 2 oxygen sensor alternate correctly.

HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DATA LIST / ACTIVE TEST




A

3.CHECK FOR EXHAUST GAS LEAK

B

8.REPLACE AIR FUEL RATIO SENSOR

C

9.CHECK FOR EXHAUST GAS LEAK

D

11.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NG

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>2NR-VE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>2NR-VE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS


Result:
Proceed to
NEXT



NEXT

END

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace exhaust gas leak point.


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC P0420 is output A
DTC is not output
(No pending DTCs output)
B



A

7.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

B

END

7.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst).

Click hereEngine / Hybrid System>2NR-VE INTAKE / EXHAUST>EXHAUST MANIFOLD>COMPONENTS


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>2NR-VE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

10.REPLACE NO. 2 OXYGEN SENSOR

NG

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
10.REPLACE NO. 2 OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
11.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

12.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

5.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
12.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>P0171


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)