Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0171  Fuel System (Lean Faulty)  P0172  Fuel System (Rich Faulty)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0171 Fuel System (Lean Faulty) With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
·

Intake system

·

Fuel injector assembly blockage

·

Intake air flow meter assembly

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

PCV valve and hose

·

PCV hose connections

·

ECM

·

Wire harness or connector


Comes on DTC stored
P0172 Fuel System (Rich Faulty) With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
·

Fuel injector assembly leak or blockage

·

Intake air flow meter assembly

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM

·

Wire harness or connector


Comes on DTC stored

HINT:
·

When DTC P0171 is stored, the actual air fuel ratio is on the lean side. When DTC P0172 is stored, the actual air fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P0171 may be stored. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.



CONFIRMATION DRIVING PATTERN

A288929E05
2.802,2.073 3.25,0.167 3.25,0.167 3.5,0.167 false 0.625,0.042 1.531,0.229 0.906,0.188 10 Vehicle Speed 1.031,0.354 1.646,0.552 0.615,0.198 10 100 km/h 1.104,1.229 1.719,1.427 0.615,0.198 10 60 km/h 1.292,2.021 1.771,2.229 0.479,0.208 10 Idling 0.49,2.271 1.656,2.448 1.167,0.177 10 Ignition Switch ON 2.031,2.344 2.646,2.542 0.615,0.198 10 [A] 3.573,0.083 6.365,0.26 2.792,0.177 10 Engine coolant temperature is 75°C or higher 3.271,1.875 3.885,2.073 0.615,0.198 10 [C] 2.521,1.875 3.135,2.073 0.615,0.198 10 [B] 4.823,0.479 5.438,0.677 0.615,0.198 10 [D] 2.146,3.115 3.26,3.302 1.115,0.188 10 Warming up 3.073,3.042 3.688,3.385 0.615,0.344 10 2 minutes or more 4.375,3.042 5.604,3.219 1.229,0.177 10 5 minutes or more 5.604,3.365 5.833,3.552 0.229,0.188 10 [E]

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

7.

With the engine warmed up, idle the engine for 2 minutes or more [C].

8.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / EFI / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:

If a pending DTC is output, the system is malfunctioning.



CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0171 or P0172 is output A
DTC P0171 or P0172 and other DTCs are output B


HINT:

If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.



A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>2NR-VE EMISSION CONTROL>PCV VALVE>COMPONENTS

OK:

PCV valve and hose are connected correctly and are not damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2NR-VE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in intake system.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)
a.

Connect the GTS or Techstream to the DLC3.


b.

Start the engine.


c.

Turn the GTS or Techstream on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / EFI / Active Test / Injection volume / All Data / AFS Voltage B1S1 and O2S B1S2.


f.

Perform the Control the Injection Volume operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and the No. 2 oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS or Techstream.

HINT:
·

The Injection volume operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS or Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status AFS Voltage B1S1 Status O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector assembly blockage

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor


Rich Rich Actual air fuel ratio rich
·

Fuel injector assembly leak or blockage

·

Gas leak from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor


Lean Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B
Rich Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor


Lean: During Injection volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the No. 2 oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Injection volume, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Injection volume of the Active Test, the output voltage of the No. 2 oxygen sensor alternates correctly.

HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DATA LIST / ACTIVE TEST




A

5.READ VALUE USING GTS OR TECHSTREAM (ENGINE COOLANT TEMPERATURE)

B

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
5.READ VALUE USING GTS OR TECHSTREAM (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / All Data / Engine coolant temperature.


e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
GTS or Techstream Display Condition Specified Condition
Engine coolant temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS OR TECHSTREAM (AIR FLOW RATE)

NG

6.READ VALUE USING GTS OR TECHSTREAM (AIR FLOW RATE)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / All Data / Air flow rate, Engine coolant temperature and Engine revolution speed.


e.

Allow the engine to idle until Engine coolant temperature reaches 75°C (167°F) or higher.


f.

Read Air flow rate with the engine speed at 3000 rpm.

Standard:
GTS or Techstream Display Condition Specified Condition
Air flow rate Shift lever position: Neutral
A/C: Off
Engine Speed: 3000 rpm
Between 3.0 and 8.0 g/s



Result:
Proceed to
OK
NG



OK

7.CHECK FUEL PRESSURE

NG

16.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY CONNECTOR CONNECTION)
7.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

8.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

9.CHECK FOR SPARK (SPARK TEST)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).




Result:
Proceed to
NEXT



NEXT

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSPECTION

HINT:
·

Refer to the fuel injector assembly inspection procedure.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSPECTION

·

If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / All Data / Cylinder #1 Misfire Count (to Cylinder #4 Misfire Count).




Result:
Proceed to
OK
NG



OK

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - EFI-MAIN RELAY)

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C37-1(HT) - C50-9(AFM) Always Below 1 Ω
C37-3(AF+) - C50-31(AF+) Always Below 1 Ω
C37-4(AF-) - C50-52(AF-) Always Below 1 Ω
C37-1(HT) or C50-9(AFM) - Body ground Always 10 kΩ or higher
C37-3(AF+) or C50-31(AF+) - Body ground Always 10 kΩ or higher
C37-4(AF-) or C50-52(AF-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC P0171 or P0172 is output A
DTC is not output B



A

16.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY CONNECTOR CONNECTION)

B

END

16.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the intake air flow meter assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC P0171 or P0172 is output A
DTC is not output B



A

18.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)

B

END

18.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)

OK

19.REPLACE INTAKE AIR FLOW METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.REPLACE INTAKE AIR FLOW METER ASSEMBLY
a.

Replace the intake air flow meter assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the intake air flow meter assembly.



Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstreamon.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P0171 or P0172 is output B



A

END

B