Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)  P2238  Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2239  Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 1 Sensor 1)  P2252  Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2253  Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P2195.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>P2195

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1) An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2238 Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 1 Sensor 1)
·

Case 1

Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):

(a) Voltage at terminal A1A+ is 0.5 V or less.

(b) Voltage difference between terminals A1A+ and A1A- is 0.1 V or less.

·

Case 2

Air fuel ratio sensor admittance: Less than 0.002 1/Ω (2 trip detection logic).


·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2239 Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 1 Sensor 1) The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2252 Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 1 Sensor 1) The A1A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2253 Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 1 Sensor 1) The A1A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on.

6.

Start the engine and wait 5 minutes or more.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C37-1 (HT) - C50-9 (AFM) Always Below 1 Ω
C37-3 (AF+) - C50-31 (AF+) Always Below 1 Ω
C37-4 (AF-) - C50-52 (AF-) Always Below 1 Ω
C37-1 (HT) or C50-9 (AFM) - Body ground Always 10 kΩ or higher
C37-3 (AF+) or C50-31 (AF+) - Body ground Always 10 kΩ or higher
C37-4 (AF-) or C50-52 (AF-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P2237, P2238, P2239, P2252 or P2253 is output B



A

END

B