Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A234900E20
1.604,2.969 0.969,2.49 false 1.823,2.969 2.094,2.667 false 2.927,1.792 3.521,0.76 false 3.052,1.792 3.615,1.427 false 3.188,2.188 3.677,1.781 false 2.844,2.396 3.573,2.198 3.573,2.198 2.99,2.396 false 3.063,2.469 3.49,2.74 false 0.156,3.292 0.99,3.635 0.833,0.344 10 Exhaust Gas 0.427,2.396 0.969,2.729 0.542,0.333 10 Element 2.125,2.573 2.521,2.875 0.396,0.302 10 Cover 1.125,3.406 1.271,3.604 0.146,0.198 10 A 2.01,3.406 2.156,3.604 0.146,0.198 10 A 3.563,0.656 4.719,1.302 1.156,0.646 10 Solid Electrolyte (Zirconia Element) 3.656,1.333 4.479,1.635 0.823,0.302 10 Alumina 3.708,1.698 4.698,1.979 0.99,0.281 10 Heater 3.604,2.125 5.021,2.469 1.417,0.344 10 Platinum Electrode 3.531,2.667 4.542,3.01 1.01,0.344 10 Atmospheric Air 2.469,3.167 3.635,3.531 1.167,0.365 10 A-A Cross Section 5.677,3.125 6.573,3.469 0.896,0.344 10 Air Fuel Ratio 5.104,0.667 7.135,1.26 2.031,0.594 10 ECM Monitored Air Fuel Ratio Sensor Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) Either of the following conditions (A) or (B) is met:
(A)

Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

1.

Air fuel ratio sensor voltage is higher than 3.8 V.

2.

No. 2 oxygen sensor voltage is 0.21 V or higher.



(B)

While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).


·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on DTC stored
P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) Either of the following conditions (A) or (B) is met:
(A)

Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

1.

Air fuel ratio sensor voltage is less than 2.8 V.

2.

No. 2 oxygen sensor voltage is less than 0.71 V.



(B)

While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic).


·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on DTC stored

HINT:
·

When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS or Techstream: Powertrain / EFI / Data List / All Data / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the GTS or Techstream.

·

The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the GTS or Techstream.

·

If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.



CONFIRMATION DRIVING PATTERN

A283818E04
2.458,1.51 3.052,0.698 3.052,0.698 2.833,0.698 true 5.448,1.667 5.75,0.583 true 5.021,1.521 4.5,1.521 false 6.333,2.25 5.375,2.25 false 4.052,3.531 3.823,3.354 true 4.938,1.688 4.5,0.583 true 5.542,3.167 5.708,3.167 5.708,3.167 5.5,2.74 true 4.708,2.958 4.875,2.958 4.875,2.958 4.99,2.729 true 0.073,0.24 3.25,0.5 3.177,0.26 10 Engine Coolant Temperature: 75°C or higher 0.156,0.865 1.104,1.094 0.948,0.229 10 Vehicle Speed 1.156,0.604 2.792,1.021 1.635,0.417 10 Between 60 and 100 km/h 0.719,2.281 1.167,2.583 0.448,0.302 10 Idling 1.25,2.865 2.083,3.083 0.833,0.219 10 Warming up 2.49,2.875 3.219,3.396 0.729,0.521 10 10 minutes or more 3.427,1.458 4.479,1.854 1.052,0.396 10 60 km/h or more 3.396,0.448 4.542,0.865 1.146,0.417 10 Accelerator Pedal Depressed 4.667,0.708 5.667,0.917 1,0.208 10 At least 3 times 5.823,0.438 7.052,0.958 1.229,0.521 10 Accelerator Pedal Released (Fuel-cut) 6.417,2.146 6.979,2.51 0.563,0.365 10 10 km/h 6.25,2.552 6.667,2.802 0.417,0.25 10 Time 4.375,3.073 5.604,3.344 1.229,0.271 10 4 seconds or more 4.094,3.469 5.417,3.667 1.323,0.198 10 Refer to figure below 3.448,2.865 4.729,3.229 1.281,0.365 10 10 seconds or more 1.552,2.167 1.813,2.385 0.26,0.219 10 [A] 2.708,1.302 2.969,1.521 0.26,0.219 10 [B] 3.844,2.167 4.083,2.417 0.24,0.25 10 [C] 4.99,1.302 5.25,1.521 0.26,0.219 10 [D] 5.5,1.594 5.76,1.813 0.26,0.219 10 [E] 6.083,3.115 6.344,3.333 0.26,0.219 10 [F]

A268801E08
3.646,2.604 3.958,0.865 false 3.365,2.625 2.156,0.688 2.156,0.688 2.281,0.688 false 0.083,0.063 2.604,0.333 2.521,0.271 10 Driving Pattern Detail for [C] through [E]: 0.177,0.635 1.792,0.917 1.615,0.281 10 Reference Engine Speed 2.823,0.156 7,0.375 4.177,0.219 10 Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 0.865,2.177 1.635,2.375 0.771,0.198 10 1200 rpm 1.094,2.438 1.51,2.635 0.417,0.198 10 Idling 2.198,2.969 2.625,3.208 0.427,0.24 10 Idling 3.167,3.104 3.865,3.521 0.698,0.417 10 4 seconds or more 4.396,3.115 5.063,3.542 0.667,0.427 10 4 seconds or more 5.604,3.125 6.271,3.583 0.667,0.458 10 4 seconds or more 2.188,2.479 2.406,2.677 0.219,0.198 10 [C] 2.833,1.146 3.073,1.344 0.24,0.198 10 [D] 3.469,1.531 3.667,1.729 0.198,0.198 10 [E] 2.354,0.615 3.531,0.844 1.177,0.229 10 Delay (3 seconds) 4.01,0.76 5.365,1.073 1.354,0.313 10 Detection Period t1 4.802,2.417 4.958,2.615 0.156,0.198 10 t2 6.021,2.427 6.177,2.646 0.156,0.219 10 t3 6.438,2.792 6.823,2.99 0.385,0.198 10 Time

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS or Techstream on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS or Techstream on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

On the GTS or Techstream, enter the following menus to check the fuel-cut status: Powertrain / EFI / Data List / All Data / Idle Fuel Cut.

9.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

With the shift lever in 2nd gear [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

Fuel-cut is performed when the following conditions are met:

·

Accelerator pedal is fully released.

·

Engine speed is 1200 rpm or higher (fuel injection restart engine speed).



12.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

13.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

14.

Enter the following menus: Powertrain / EFI / Trouble Codes [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360376E05
0.75,0.604 1.063,0.802 0.313,0.198 10 false 1F 0.75,0.417 0.948,0.604 0.198,0.188 10 false 17 2.802,0.604 3.115,0.802 0.313,0.198 10 false 1J 2.833,0.438 2.99,0.635 0.156,0.198 10 false 3 2.792,1.146 3.104,1.344 0.313,0.198 10 false 1F 2.844,0.958 3,1.156 0.156,0.198 10 false 5 1.823,1.469 3.052,1.667 1.229,0.198 10 false EFI-MAIN 1.167,1.76 2.656,2.146 1.49,0.385 10 false No. 1 Integration Relay 0.417,2.563 0.875,2.76 0.458,0.198 10 false EFI 0.438,3.198 1.052,3.458 0.615,0.26 10 false FL MAIN 0.594,3.917 1.156,4.219 0.563,0.302 10 false Battery 3.667,0.5 4.083,0.719 0.417,0.219 10 false +B 3.427,0.5 3.583,0.698 0.156,0.198 10 false 2 4.583,0.5 4.802,0.75 0.219,0.25 10 false HT 4.844,0.5 5,0.698 0.156,0.198 10 false 1 3.635,1.167 3.917,1.333 0.281,0.167 10 false AF- 3.427,1.167 3.583,1.365 0.156,0.198 10 false 4 4.5,1.167 4.813,1.344 0.313,0.177 10 false AF+ 4.844,1.167 5,1.365 0.156,0.198 10 false 3 3.5,1.75 3.813,2 0.313,0.25 10 false C37 3.802,1.75 5.177,2.115 1.375,0.365 10 false Air Fuel Ratio Sensor 3.177,4.188 3.979,4.448 0.802,0.26 10 false *:Shielded 6.375,3.615 6.833,3.813 0.458,0.198 10 false ECM 5.802,3.042 6.26,3.24 0.458,0.198 10 false A24 5.854,2.865 6.167,3.063 0.313,0.198 10 false 28 6.135,3.052 6.594,3.25 0.458,0.198 10 false MRO 6.125,2.635 6.583,2.833 0.458,0.198 10 false AF- 5.802,2.625 6.26,2.823 0.458,0.198 10 false C50 5.854,2.458 6.167,2.656 0.313,0.198 10 false 52 6.135,1.26 6.448,1.458 0.313,0.198 10 false AF+ 5.802,1.25 6.26,1.448 0.458,0.198 10 false C50 5.854,1.073 6.167,1.271 0.313,0.198 10 false 31 6.125,0.594 6.531,0.813 0.406,0.219 10 false AFM 5.792,0.594 6.25,0.792 0.458,0.198 10 false C50 5.896,0.417 6.052,0.615 0.156,0.198 10 false 9 5.354,2.875 5.51,3.073 0.156,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195 OR P2196)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2195 or P2196 is output A
DTC P2195 or P2196 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

NO

4.READ VALUE USING GTS OR TECHSTREAM (AFS CURRENT B1S1)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P2195 or P2196 is output B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING GTS OR TECHSTREAM (AFS CURRENT B1S1)
4.READ VALUE USING GTS OR TECHSTREAM (AFS CURRENT B1S1)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Enter the following menus: Powertrain / EFI / Data List / All Data / AFS Current B1S1.


f.

Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.

HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS or Techstream.




Result:
Test Value Proceed to
Within normal range
(0.7 mA or higher, and lower than 2.2 mA)
A
Outside normal range
(lower than 0.7 mA, or 2.2 mA or higher)
B



A

5.READ VALUE USING GTS OR TECHSTREAM (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

13.REPLACE AIR FUEL RATIO SENSOR
5.READ VALUE USING GTS OR TECHSTREAM (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Start the engine.


c.

Turn the GTS or Techstream on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / EFI / Active Test / Injection volume / All Data / AFS Voltage B1S1 and O2S B1S2.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and No. 2 oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS or Techstream.

HINT:
·

The Injection volume operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS or Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction
Lean/Rich Lean/Rich Normal


Lean: During the Injection volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the No. 2 oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During the Injection volume Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During the Injection volume Active Test, the output voltage of the air fuel ratio sensor and the No. 2 oxygen sensor alternates correctly.

HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DATA LIST / ACTIVE TEST




A

6.CHECK INTAKE SYSTEM

B

13.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2NR-VE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.



Result:
Proceed to
OK
NG



OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL INJECTOR ASSEMBLY

NG

12.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

10.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC P2195 or P2196 is output A
DTC is not output B



A

REPLACE ECM

B

END

12.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE

13.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P2195 or P2196 is output B



A

END

B