Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1210/93  Zero Point Calibration of Yaw Rate Sensor Undone (Check Mode)  C1327/99  Zero Point Calibration of Right / Left G Sensor Undone (Check Mode)  C1336/92  Zero Point Calibration of G Sensor Undone (Check Mode)  


DESCRIPTION

The yaw rate sensor and the G sensor are built-into the skid control ECU (brake actuator assembly).

DTCs C1210/93, C1327/99 and C1336/92 are cleared when the yaw rate sensor and G sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1210/93, C1327/99 and C1336/92 are output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1210/93 Zero Point Calibration of Yaw Rate Sensor Undone (Check Mode) Stored during Test Mode.
·

Steering sensor (switch base)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

CAN communication system


-
C1327/99 Zero Point Calibration of Right / Left G Sensor Undone (Check Mode) Stored during Test Mode.
·

Steering sensor (switch base)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

CAN communication system


-
C1336/92 Zero Point Calibration of G Sensor Undone (Check Mode) Stored during Test Mode.
·

Steering sensor (switch base)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

CAN communication system


-

CAUTION / NOTICE / HINT

NOTICE:

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CHECK BRAKE ACTUATOR ASSEMBLY INSTALLATION
a.

Check that the brake actuator assembly has been installed properly.

OK:

The brake actuator assembly installation is normal.


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS (YAW RATE SENSOR AND G SENSOR)

NG

INSTALL BRAKE ACTUATOR ASSEMBLY CORRECTLY

2.READ VALUE USING GTS (YAW RATE SENSOR AND G SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw rate sensor 1 Yaw rate sensor Min.: -128 deg/s
Max.: 127 deg/s
Vehicle stopped: 1 deg/s
Turning right: -128 to 3 deg/s
Turning left: 2 to 127 deg/s
-
Right/Left G (Controlled) Right/Left G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During turning: Changes inproportion with acceleration
Front/Rear G (Controlled) Front/Rear G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During acceleration/deceleration: Changes inproportion with acceleration


g.

Drive at low speeds and check the changes in output values of yaw rate sensor and the G sensor when making turns and applying hard braking.

OK:

The output values change in proportion to the vehicle inclination of front/rear and left/right.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STEERING ANGLE SENSOR)

NG

3.READ VALUE USING GTS (STEERING ANGLE SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering angle sensor Steering angle sensor Min.: -3276.8 deg
Max.: 3276.8 deg
Turning left: Positive value increases
Turning right: Negative value decreases
-

OK:

The output values change in response to the steering operation.



Result:
Proceed to
OK
NG



OK

4.INSPECT VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH)

NG

4.INSPECT VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH)
a.

Inspect the VSC OFF switch (vehicle stability control switch).

for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(for LHD)>INSPECTION

for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(for RHD)>INSPECTION

OK:

The VSC OFF switch (vehicle stability control switch) operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH))

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VSC OFF SWITCH (VEHICLE STABILITY CONTROL SWITCH))
a.

Disconnect the E34 combination meter assembly connector.


b.

Disconnect the E93*1 or E95*2 VSC OFF switch (vehicle stability control switch) connector.

*1: for RHD

*2: for LHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
E34-17 (TCS) - E93-3 (B) Always Below 1 Ω
E34-17 (TCS) or E93-3 (B) - Body ground Always 10 kΩ or higher
E93-4 (L) - Body ground Always Below 1 Ω


Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
E34-17 (TCS) - E93-3 (B) Always Below 1 Ω
E34-17 (TCS) or E93-3 (B) - Body ground Always 10 kΩ or higher
E93-4 (L) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR