Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.09
RM19Y0E _53 Suspension _059025 TIRE PRESSURE MONITORING _0288381 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2126/26  Transmitter ID not Received in Main Mode  


DESCRIPTION

After all transmitter IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates.

When the tire pressure warning ECU and receiver successfully receives radio waves from all the transmitters whose IDs are stored in the ECU, DTC C2126/26 is cleared and the tire pressure warning light goes off.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2126/26 Transmitter ID not Received in Main Mode After transmitter ID registration is completed, ECU does not receive radio waves from transmitters whose IDs are stored in ECU.
·

Transmitter ID registration failure

·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver



HINT:

The purpose of this DTC is to help prevent delivering a vehicle that has incorrectly registered transmitter IDs. After all IDs are registered, DTC C2126/26 is detected and the tire pressure warning light blinks for 1 minute and then illuminates. If the tire pressure warning light does not go off after a little while, the transmitter IDs may be incorrectly registered.


WIRING DIAGRAM

C364608E01
0.563,0.896 1.948,1.76 1.385,0.865 10 false Tire Pressure Warning Valve and Transmitter 0.563,1.969 1.927,2.74 1.365,0.771 10 false Tire Pressure Warning Valve and Transmitter 3.052,0.365 4.438,1.229 1.385,0.865 10 false Tire Pressure Warning Valve and Transmitter 3.073,1.427 4.458,2.292 1.385,0.865 10 false Tire Pressure Warning Valve and Transmitter 3.073,2.49 4.458,3.354 1.385,0.865 10 false Tire Pressure Warning Valve and Transmitter 0.167,4.313 2.354,4.75 2.188,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 0.188,4.135 0.573,4.448 0.385,0.313 10 false A13 0.844,4.958 1.927,5.302 1.083,0.344 10 false from IG Circuit 3.625,5.125 4.063,5.417 0.438,0.292 10 false IG1 3.198,4.469 5.385,4.906 2.188,0.438 10 false Combination Meter Assembly 3.198,4.302 3.635,4.594 0.438,0.292 10 false E34 5.531,3.49 6.219,3.792 0.688,0.302 10 false SPEED 4.385,3.49 5.01,3.823 0.625,0.333 10 false SPDO 4.521,3.979 5,4.281 0.479,0.302 10 false IND 5.542,3.979 6.167,4.313 0.625,0.333 10 false IND 4.875,3.375 5.25,3.677 0.375,0.302 10 false 10 4.885,3.865 5.365,4.167 0.479,0.302 10 false 34 5.542,4.969 5.979,5.26 0.438,0.292 10 false IG1 3.542,6.896 4.083,7.333 0.542,0.438 10 false DLC3 3.167,6.885 3.708,7.323 0.542,0.438 10 false E12 3.781,5.823 4.323,6.26 0.542,0.438 10 false ECUT 3.188,6.469 3.729,6.906 0.542,0.438 10 false E 3.24,3.333 3.719,3.635 0.479,0.302 10 false 9 1.563,3.5 2,3.75 0.438,0.25 10 false CANH 3.438,3.969 4.01,4.292 0.573,0.323 10 false CANL 3.438,3.49 4.01,3.823 0.573,0.333 10 false CANH 1.563,3.979 2.135,4.302 0.573,0.323 10 false CANL 3.229,3.802 3.708,4.104 0.479,0.302 10 false 8 2.042,3.802 2.521,4.104 0.479,0.302 10 false 10 2.052,3.333 2.531,3.635 0.479,0.302 10 false 22 5.313,3.865 5.792,4.167 0.479,0.302 10 false 5 5.313,3.375 5.583,3.698 0.271,0.323 10 false 2 5.302,4.844 5.781,5.146 0.479,0.302 10 false 1 5.542,5.813 5.979,6.104 0.438,0.292 10 false Tc 5.531,6.479 6.073,6.854 0.542,0.375 10 false SIL 5.531,7.917 6.073,8.229 0.542,0.313 10 false CLSW 2.99,7.781 3.469,8.083 0.479,0.302 10 false 1 3.177,7.802 3.656,8.104 0.479,0.302 10 false CL- 3.906,7.792 4.385,8.094 0.479,0.302 10 false CL+ 4.292,7.781 4.771,8.083 0.479,0.302 10 false 4 5.396,9.021 5.875,9.323 0.479,0.302 10 false K6 3.906,6.469 4.448,6.844 0.542,0.375 10 false SIO 5.24,6.323 5.719,6.625 0.479,0.302 10 false 10 4.26,6.333 4.74,6.635 0.479,0.302 10 false 7 5.313,5.698 5.792,6 0.479,0.302 10 false 3 2.979,6.323 3.458,6.625 0.479,0.302 10 false 4 4.25,5.708 4.729,6.01 0.479,0.302 10 false 13 5.302,7.781 5.781,8.083 0.479,0.302 10 false 7 5.552,8.302 6.094,8.677 0.542,0.375 10 false GND 5.542,8.677 6.083,9.052 0.542,0.375 10 false GND3 5.25,8.188 5.729,8.49 0.479,0.302 10 false 12 5.323,8.583 5.802,8.885 0.479,0.302 10 false 9 3.021,8.302 3.563,8.74 0.542,0.438 10 false E96 3.031,8.458 4.417,9.01 1.385,0.552 10 false Tire Pressure Warning Reset Switch 5.396,9.188 6.781,9.74 1.385,0.552 10 false Tire Pressure Warning ECU and Receiver 0.76,9.042 1.938,9.354 1.177,0.313 10 false : Radio Waves 0.771,9.417 2.719,9.802 1.948,0.385 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.IDENTIFY TRANSMITTER NOT RECEIVED
a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Display the "ID Tire Inflation Pressure" value for each wheel using the GTS.


h.

Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the GTS does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value was the cause of the output DTC.

HINT:
·

Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.

·

Record which "ID Tire Inflation Pressure" value corresponds to each tire.



Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID5 Tire Inflation Pressure ID5 tire Inflation Pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/ cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1

HINT:
·

*1: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID5 on the Data List.




i.

Check the Data List.

NOTICE:
·

It may take a few minutes until the values are displayed.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.

·

Record the transmitter IDs and positions of transmitters that are normal.




j.

After confirming that the "ID Tire Inflation Pressure" value for one tire has changed, repeat this procedure one by one. Identify the transmitter not received.


Result:
Result Proceed to
One or more transmitter is abnormal A
All transmitters are normal B



A

2.CHECK TRANSMITTER ID

B

END

2.CHECK TRANSMITTER ID
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID1 Code Registered ID1 Code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID1 displayed -
Registered ID2 Code Registered ID2 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID2 displayed -
Registered ID3 Code Registered ID3 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID3 displayed -
Registered ID4 Code Registered ID4 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID4 displayed -
Registered ID5 Code Registered ID5 code min.: 0
max.: FFFFFFF*1
ID No. registered for transmitter ID5 displayed -

HINT:
·

*1: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID5 on the Data List.




g.

Check the ID number on the identified transmitter by removing it from the tire and wheel.


C349073C01
6.125,1.313 6.458,0.979 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *1 6.51,0.885 6.823,1.042 0.313,0.156 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -


h.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B



A

3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

4.REGISTRATION OF TRANSMITTER ID
3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
a.

Replace the tire pressure warning valve and transmitter.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING VALVE>REASSEMBLY


Result:
Proceed to
NEXT



NEXT

4.REGISTRATION OF TRANSMITTER ID
4.REGISTRATION OF TRANSMITTER ID

Result:
Proceed to
NEXT



NEXT

5.PERFORM INITIALIZATION
5.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

6.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
6.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
a.

Turn the ignition switch off.


b.

Connect GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


f.

Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1
ID2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) /380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed,data has not been received.*1
ID5 Tire Inflation Pressure ID5 tire Inflation Pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/ cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*1

HINT:
·

*1: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID5 on the Data List.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.




Result:
Result Proceed to
Tire pressure values are not displayed. A
All tire pressure readings are equal to specified values. B



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

END