Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.09
RM19Y0E _58 Vehicle Interior _003008 METER / GAUGE / DISPLAY _0015206 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. For details about testing and the margin of error, see the reference chart


The combination meter assembly controls the speedometer in accordance with vehicle speed signals fromthe skid control ECU (brake actuator assembly) through the CAN communication system.

HINT:

If the vehicle speed sensor circuit has a malfunction, the skid control ECU (brake actuator assembly)stores DTCs. Troubleshoot the anti-lock brake system or vehicle stability control system.



WIRING DIAGRAM

E324172E03
0.427,1.448 2.615,1.708 2.188,0.26 10 false : CAN Communication Line 0.531,1.135 3.427,1.5 2.896,0.365 10 false Skid Control ECU (Bake Actuator Assembly) 4.51,1.135 6.698,1.521 2.188,0.385 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FOR DTC (METER / GAUGE SYSTEM)
a.

Check if meter / gauge system DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

OK:

DTCs are not output.



Result:
Result Proceed to
OK (w/o VSC) A
OK (w/ VSC) B
NG C



A

2.CHECK DTC (ANTI-LOCK BRAKE SYSTEM)

B

4.CHECK DTC (VEHICLE STABILITY CONTROL SYSTEM)

C

2.CHECK DTC (ANTI-LOCK BRAKE SYSTEM)
a.

Check if anti-lock brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (Speed meter)

NG

3.PERFORM ACTIVE TEST USING GTS (Speed meter)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS or Techstream.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed meter Speedometer 0, 40, 80, 120, 160, 200 km/h The meter needle goes off the scale when 200 km/h is selected.

OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check if vehicle stability control system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (Speed meter)

NG

5.PERFORM ACTIVE TEST USING GTS (Speed meter)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS or Techstream.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed meter Speedometer 0, 40, 80, 120, 160, 200 km/h The meter needle goes off the scale when 200 km/h is selected.

OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE COMBINATION METER ASSEMBLY