Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0ABF00  Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance  


DESCRIPTION

A battery current sensor is installed to the positive (+) terminal side of the HV battery and detects current flowing from the HV battery. The battery current sensor outputs voltage, which changes between 0 and 5 V according to the detected amperage, to the IB terminal of the battery voltage sensor. The battery voltage sensor sends signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU determines the charging and discharging amount of the HV battery based on the received signals and calculates the SOC of the HV battery through the accumulated amperage.

A304993E21
0.052,0.073 0.625,0.521 0.573,0.448 10 false Charging Current 0.719,0.083 1.479,0.552 0.76,0.469 10 false Discharging Current 0.875,1.01 2.563,1.25 1.688,0.24 10 false Battery Current Sensor 2.094,2.677 3.688,2.948 1.594,0.271 10 false Battery Voltage Sensor 2.406,1.26 2.865,1.458 0.458,0.198 10 false VIB 2.417,1.563 2.729,1.76 0.313,0.198 10 false IB 2.406,1.865 2.865,2.063 0.458,0.198 10 false GIB 3.177,0.104 6,0.323 2.823,0.219 10 false Battery Current Sensor Output Voltage 3.969,0.469 4.427,0.667 0.458,0.198 10 false (V) 3.958,0.865 4.417,1.063 0.458,0.198 10 false 4.5 3.969,1.594 4.427,1.792 0.458,0.198 10 false 2.5 3.969,2.323 4.427,2.521 0.458,0.198 10 false 0.5 4.25,2.625 4.865,2.823 0.615,0.198 10 false -200 5.594,2.625 5.75,2.823 0.156,0.198 10 false 0 6.729,2.625 7.063,2.823 0.333,0.198 10 false 200 4.229,3.083 4.865,3.271 0.635,0.188 10 false Charge 6.49,3.083 7.146,3.302 0.656,0.219 10 false Discharge 4.948,3.198 6.25,3.427 1.302,0.229 10 false HV Battery Current 6.188,3.188 6.531,3.417 0.344,0.229 10 false (A)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance Abnormal battery current sensor characteristics:
(based on hybrid system consumption and HV battery output).
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery voltage sensor


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0ABF00 -

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Current", "Motor Torque" and "Generator Torque".

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
One of the following applies:
·

Only P0ABF00 is output.

·

One or more DTCs other than P0AFC00 and P0AFC96 are also output.


A
P0AFC00 or P0AFC96 is also output. B


e.

Turn the power switch off.


f.

Disconnect the GTS from the DLC3.



A

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

3.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

3.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

4.CLEAR DTC
4.CLEAR DTC

NEXT

5.PERFORM ROAD TEST
5.PERFORM ROAD TEST
a.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Current", "Motor Torque" and "Generated Torque".

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT (HYBRID CONTROL)
6.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0ABF00 is not output. A
P0ABF00 is output again. B



e.

Turn the power switch off.



A

COMPLETED

B