The hybrid vehicle control ECU monitors the system internal operation, it will store a DTC and perform fail-safe control if it detects the following malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P1C8549 | High Voltage Power Resource Internal Electronic Failure | Battery overcurrent or overload current occurs due to a malfunction in the high-voltage circuit between the hybrid system, battery and inverter.
(1 trip detection logic) |
·
Hybrid vehicle control ECU ·
HV battery junction block assembly ·
Battery voltage sensor ·
Wire harness or connector |
Does not come on | Master Warning Light:
Comes on |
| DTC No. | Data List |
|---|---|
| P1C8549 | ·
Hybrid Battery Current ·
Hybrid Battery Voltage ·
VL-Voltage before Boosting ·
VH-Voltage after Boosting |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position" and "Hybrid Battery Current".
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1C8549 only is output. | A |
| DTCs other than P1C8549 is also output. | B |
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Current.
| Tester Display |
|---|
| Hybrid Battery Current |
Read the Data List.
| Result | Proceed to |
|---|---|
| The value of Hybrid Battery Current is between -4 A and 4 A | A |
| Other than above | B |
Turn the power switch off.
A
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery cover panel RH.
Disconnect the battery current sensor connector from the HV battery junction block assembly.
Before disconnecting the connector, check that it is not loose or disconnected.
Remove the No. 1 hybrid battery exhaust duct.
Disconnect the battery voltage sensor connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Battery Voltage Sensor) |
| *b | Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor)) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z12-5 (IB0) - z13-4 (IB0) | Power switch off | Below 1 Ω |
| z12-12 (GIB) - z13-3 (GIB) | Power switch off | Below 1 Ω |
| z12-6 (VIB) - z13-1 (VIB) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z12-5 (IB0) or z13-4 (IB0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z12-12 (GIB) or z13-3 (GIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z12-6 (VIB) or z13-1 (VIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
As the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery.
Reconnect the battery voltage sensor connector.
Install the No. 1 hybrid battery exhaust duct.
Reconnect the battery current sensor connector to the HV battery junction block assembly.
Install the No. 1 HV battery cover panel RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 hybrid battery exhaust duct.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
| *a | Component with harness connected
(Battery Voltage Sensor) |
Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.
| Tester Connection | Tester Connection |
|---|---|
| z12-6 (VIB) - z12-12 (GIB) | Power switch on (IG) |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Be sure to set the toyota electrical tester to 40 V when performing this test.
| *a | Component with harness connected
(Battery Voltage Sensor) |
Using a toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.
| Tester Connection | Tester Connection |
|---|---|
| z12-5(IB0) - z12-12(GIB) | Power switch on (IG) |
Be sure to set the toyota electrical tester to 4 V when performing this test.
Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:
| IB0 voltage - VIB Voltage / 2 = less than 0.081 V |
| IB0 voltage - VIB Voltage / 2 = -0.081 V or higher |
| Result | Proceed to |
|---|---|
| Within the specified range above | A |
| Other than above | B |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the No. 1 hybrid battery exhaust duct.
When the power switch is on (IG) the actual current will be approximately 0 A. The following graph shows the relation of the actual output voltage of the battery current sensor terminal IB0 and actual current used for DTC judgment.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Clear the DTCs.
Drive the vehicle on urban roads for approximately 10 minutes.
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and wait for 10 seconds or more.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
Turn the power switch off.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P1C8549 is output | B |
A
B