Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292496 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  INSTALLATION  


PROCEDURE

Hide 821H1 1.INSTALL HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.
A391984C01
0.083,0.177 0.354,0.396 0.271,0.219 12 true *A 0.844,1.188 1.042,1.385 0.198,0.198 10 true A 2.948,1.313 3.146,1.51 0.198,0.198 10 true B 0.104,2.573 0.375,2.792 0.271,0.219 12 true *B 2.875,3.792 3.073,3.99 0.198,0.198 10 true B 1.021,3.646 1.219,3.844 0.198,0.198 10 true A
*A for LHD
*B for RHD


Engage the clamp (B).


b.

Install a new clamp (A).


c.
A391983

Insert the HV floor under wire into the floor panel hole and engage the grommet.


d.

Install 3 new clamps in the order shown in the illustration.

A391982N01
1.083,1.75 1.24,1.948 0.156,0.198 10 true 1 3.344,1.74 3.5,1.938 0.156,0.198 10 true 2 5.958,1.75 6.115,1.948 0.156,0.198 10 true 3


e.
A391981

Install the HV floor under wire with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 51201 2.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 58165B 3.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.

Click hereEngine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>INSTALLATION


Hide 57627A 4.INSTALL REAR FLOOR SIDE MEMBER COVER RH

Hide 821H1 5.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 6.INSTALL NO. 1 HV BATTERY COVER PANEL RH

Hide 71033 7.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 76974F 9.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 10.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 11.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67917A 12.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 72693 13.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 14.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 82121 16.CONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Engage the 2 clamps and connect the engine wire.


b.

Install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.
A391971

Connect the 2 inverter with converter assembly connectors and move each lock lever as shown in the illustration.

NOTICE:
·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.

·

Do not touch the waterproof seal or terminals of the connector.