Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY VOLTAGE SENSOR › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292491 BATTERY VOLTAGE SENSOR A

HYBRID / BATTERY CONTROL  BATTERY VOLTAGE SENSOR  INSTALLATION  


PROCEDURE

Hide 89892A 1.INSTALL BATTERY VOLTAGE SENSOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375905C02
1.385,1.26 2.01,2.188 2.01,2.188 2.271,2.188 true 0.906,2.781 1.615,2.781 true 2.323,2.104 2.635,2.302 0.313,0.198 10 false *a 1.677,2.698 1.99,2.896 0.313,0.198 10 false *b
*a Black Label
*b Pin


Install the battery voltage sensor to the HV battery with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·

Check color of the label.

·

If the battery voltage sensor has been struck or dropped, replace it.

·

Make sure to align the hole of the battery voltage sensor with the pin.




b.

Connect the battery voltage sensor connector.

NOTICE:

Make sure that the connector is connected securely.



Hide G92Q1 2.INSTALL NO. 1 HV BATTERY SHIELD PANEL

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Pull back the No. 2 hybrid battery shield sub-assembly to install the No. 1 HV battery shield panel to the HV battery.

HINT:

Pull back the No. 2 hybrid battery shield sub-assembly until there is sufficient clearance for the 2 stud bolts of the No. 1 HV battery shield panel.



b.

Install the bolt and 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Connect the battery voltage sensor connector.


d.

Engage the clamp.


Hide G920L 3.INSTALL UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Install the upper No. 1 hybrid battery cover sub-assembly to the HV battery with the 6 bolts and 5 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Move the HV battery to the installation position.


c.
A378149C02
1.688,0.083 1.948,0.281 0.26,0.198 10 true *b 2.198,0.333 2.458,0.531 0.26,0.198 10 true *a 3,0.667 3.26,0.865 0.26,0.198 10 true *a 2.948,1.938 3.208,2.135 0.26,0.198 10 true *a 0.073,0.438 0.333,0.635 0.26,0.198 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))


Install the 4 bolts (A) and bolt (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide G92F1 5.INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT

Hide 821H1 7.CONNECT HV FLOOR UNDER WIRE

Hide G92N4A 8.INSTALL NO. 1 HV BATTERY COVER PANEL RH

Hide G9230 9.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 71033 10.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 76974F 12.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 13.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 14.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67917A 15.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 72693 16.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 17.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY