G92D1
1.INSTALL NO. 1 HYBRID BATTERY INTAKE DUCT
G920Q
2.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY
3.INSTALL HV BATTERY JUNCTION BLOCK ASSEMBLY
G92Z2
4.INSTALL HYBRID BATTERY TERMINAL BLOCK
89892A
5.INSTALL BATTERY VOLTAGE SENSOR
G92Q1
6.INSTALL NO. 1 HV BATTERY SHIELD PANEL
G920L
7.INSTALL UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY
Be sure to wear insulated gloves and protective goggles.
| *a | Bolt |
| *b | Nut |
Install the upper No. 1 hybrid battery cover sub-assembly to the HV battery with the 6 bolts and 5 nuts.
8.INSTALL HV BATTERY
Wear insulated gloves.
| *a | Bolt (A)
(Bolt Length: 25 mm (0.984 in.)) |
| *b | Bolt (B)
(Bolt Length: 24 mm (0.945 in.)) |
Install the HV battery to the vehicle with the 4 bolts (A) and bolt (B).
Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.
To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.
Use cardboard or another similar material to protect the HV battery and vehicle body from damage.
Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.
When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.
While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.
As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.
If the HV battery has been struck or dropped, replace it.
82161
9.CONNECT FLOOR WIRE
Wear insulated gloves.
Connect the battery voltage sensor connector.
Engage the clamp.
G92F1
10.INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT
Engage the claw to install the No. 1 hybrid battery exhaust duct to the HV battery.
Install the clip.
82161
11.CONNECT FLOOR WIRE
Wear insulated gloves.
Connect the HV battery junction block assembly connector.
Connect the electric vehicle battery plug assembly connector.
Engage the clamp.
821H1
12.CONNECT HV FLOOR UNDER WIRE
Wear insulated gloves.
Connect the shield ground to the HV battery.
Connect the 2 HV battery junction block assembly connectors.
Make sure that the connectors are connected securely.
G92N4A
13.INSTALL NO. 1 HV BATTERY COVER PANEL RH
Wear insulated gloves.
| *1 | Battery Cover Lock Striker |
| *a | Button |
| *b | Push |
Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 2 nuts.
Install the battery cover lock striker, then push the button to lock it.
G9230
14.INSTALL BATTERY COOLING BLOWER ASSEMBLY
71033
15.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY
Install the rear seat cushion leg sub-assembly with the 6 bolts.
76971G
16.INSTALL REAR UNDER COVER
Engage the 2 guides to install the rear under cover to the rear seat cushion leg sub-assembly.
Engage the 2 clips.
76974F
17.INSTALL REAR UNDER SIDE COVER LH
67918A
18.INSTALL REAR DOOR SCUFF PLATE LH
76973F
19.INSTALL REAR UNDER SIDE COVER RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67917A
20.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
72693
21.INSTALL REAR SEAT CUSHION LOCK HOOK
22.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
G3834
23.INSTALL SERVICE PLUG GRIP
24. PERFORM BATTERY STATUS INFO UPDATE