Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _060063 2ZR-FXE FUEL _0294218 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.
A395935C01
1,2.833 1.833,2.854 true 0.365,0.74 0.531,0.99 false 0.771,2.75 1.083,2.948 0.313,0.198 10 false *b 0.188,0.625 0.5,0.823 0.313,0.198 10 false *a
*a Protrusion
*b Notch


Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Be careful not to bend the arm of the fuel sender gauge assembly.

·

Make sure the horizontal angle of the plate sub-assembly is less than 90°.

·

To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.


A395936C01
1.938,2.052 2.354,2.052 true 5.948,2.313 6.333,2.083 true 1.771,1.667 2.313,1.427 true 5.708,2.552 5.51,2.208 true 2.01,0.729 2.396,0.521 false 5.635,1.271 6.021,1.063 false 2.427,1.979 2.74,2.177 0.313,0.198 10 false *1 2.396,1.344 2.708,1.542 0.313,0.198 10 false *2 6.417,2 6.729,2.198 0.313,0.198 10 false *1 5.76,2.542 6.073,2.74 0.313,0.198 10 false *2 2.458,0.438 2.771,0.635 0.313,0.198 10 false *3 6.104,0.969 6.417,1.167 0.313,0.198 10 false *3 0.438,0.5 0.75,0.698 0.313,0.198 10 false *a
*1 Fuel Sender Gauge Assembly *2 Fuel Sub-tank Sub-assembly
*3 Plate Sub-assembly - -
*a 90° - -




c.
A393837C01
0.938,1.115 2.75,0.25 true 2.406,1.063 2.75,0.25 true 0.479,2.583 0.813,2.583 true 2.781,0.083 2.979,0.281 0.198,0.198 10 true *a 0.281,2.479 0.479,2.677 0.198,0.198 10 true *a
*a Protrusion
V100135

Notch


Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A374375C01
0.99,0.281 1.521,0.281 true 2.604,0.604 2.781,0.604 true 1.958,1.125 2.5,1.125 true 1.958,2.042 1.958,1.604 true 0.854,3.094 1.625,3.094 true 1.667,3.01 1.833,3.188 0.167,0.177 10 true *a 2.823,0.531 3.021,0.688 0.198,0.156 10 true *b 1.885,2.042 2.083,2.208 0.198,0.167 10 true *c 0.833,0.198 1.01,0.354 0.177,0.156 10 true *d 2.542,1.052 2.719,1.208 0.177,0.156 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A393838C01
2.021,2.073 2.021,1.74 true 1.031,3.563 1.365,3.563 true 0.313,3.563 0.646,3.563 true 1,1.333 0.667,1 true 1.906,1.385 2.49,1.385 true 1.51,0.708 1.75,0.417 true 1,0.5 1.479,0.844 true 1.385,3.448 1.594,3.646 0.208,0.198 10 true *a 0.083,3.469 0.292,3.667 0.208,0.198 10 true *b 0.5,0.833 0.708,1.042 0.208,0.208 10 true *c 1.792,0.292 2,0.5 0.208,0.208 10 true *d 1.938,2.094 2.156,2.292 0.219,0.198 10 true *e 0.781,0.333 1,0.552 0.219,0.219 10 true *f 2.531,1.281 2.75,1.5 0.219,0.219 10 true *f
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Claw)
*f SST (Bolt)
V100135

Tighten
V100136

Front Side of Vehicle


Install SST (handle) to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer are aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the plate sub-assembly, then install the tube joint clip.

A393839C01
5.667,1.417 6.75,2.667 1.083,1.25 4.083,1.417 5.167,2.667 1.083,1.25 0.531,1 0.865,1 false 1.5,1.25 1.25,0.667 true 5.625,0.333 5.958,0.333 false 5.823,0.604 6.156,0.604 false 4.667,1 4.917,0.76 false 6.167,1.906 6.333,1.667 true 4.833,2.25 4.542,1.969 true 5.615,0.865 6.167,0.865 true 5.615,0.75 6,0.75 6,0.75 6,0.865 true 4.51,1.01 4.823,1.177 0.313,0.167 10 false *1 6.198,0.49 6.51,0.646 0.313,0.156 10 false *2 1.083,0.49 1.292,0.667 0.208,0.177 10 true *3 5.99,0.229 6.302,0.385 0.313,0.156 10 false *a 6.198,0.75 6.51,0.906 0.313,0.156 10 false *b 4.125,1.458 4.438,1.615 0.313,0.156 10 false *c 5.708,1.458 6.021,1.615 0.313,0.156 10 false *d 4.875,2.219 5.188,2.375 0.313,0.156 10 false *e 0.323,0.896 0.635,1.052 0.313,0.156 10 false *2 6.344,1.51 6.656,1.667 0.313,0.156 10 false *e
*1 Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
*e Collar - -
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 58325E 4.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the fuel pump connector.


d.

Install the rear floor service hole cover with new butyl tape.


Hide 82818G 5.INSTALL NO. 8 WIRING HARNESS PROTECTOR

a.

Install a new No. 8 wiring harness protector to the rear floor service hole cover.


Hide 71305A 6.INSTALL CENTER REAR SEATBACK HINGE SUB-ASSEMBLY

a.

Install the center rear seatback hinge sub-assembly to the vehicle body with the 2 bolts.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 73380A 7.INSTALL REAR SEAT INNER BELT ASSEMBLY

Hide 73480 8.INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 11.INSTALL REAR SEAT ASSEMBLY

Hide 12.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION