Home › Engine / Hybrid System › 2ZR-FXE (COOLING) › COOLING FAN SYSTEM
RM32K0E _51 Engine / Hybrid System _060780 2ZR-FXE COOLING _0298024 COOLING FAN SYSTEM J

2ZR-FXE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, air conditioning switch (on/off), air conditioning refrigerant pressure, engine speed and vehicle speed signals.

The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan
50004 372 26

e.

Perform the Active Test according to the display on the GTS.

OK:
Active Tester Operation Fan Operation
HIGH Cooling fans high speed operate
LOW Cooling fans low speed operate
OFF Cooling fans stop



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (FANL - FANH POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (FANL - FANH POWER SOURCE)
a.

Disconnect the A38 ECM connector.


b.

Turn the power switch on (IG).


c.
A345274C12
0.271,0.781 0.74,1.094 0.469,0.313 2.708,0.365 2.198,1.125 true 2.073,1.135 0.844,1.438 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 0.375,0.865 0.688,1.063 0.313,0.198 10 false A38 0.604,1.469 1.073,1.74 0.469,0.271 10 false FANL 2.656,0.167 3.125,0.438 0.469,0.271 10 false FANH
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-8 (FANH) - Body ground Power switch on (IG) 11 to 14 V
A38-7 (FANL) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)

NG

12.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)
3.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)
a.

Remove the FAN NO. 1 relay and FAN NO. 3 relay from the No. 2 relay block.


b.
A375061C02
0.188,0.198 0.5,0.396 0.313,0.198 10 false *1 1.063,2.521 1.375,2.719 0.313,0.198 10 false *2 2.208,0.25 2.521,0.448 0.313,0.198 10 false *3
*1 No. 2 Relay Block
*2 FAN NO. 1 Relay
*3 FAN NO. 3 Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V
3 (FAN NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)

4.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)
a.

Inspect the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay.

Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>RELAY>ON-VEHICLE INSPECTION


Result:
Result Proceed to
OK A
NG (FAN NO. 1 relay) B
NG (FAN NO. 2 relay) C
NG (FAN NO. 3 relay) D



A

5.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

B

REPLACE FAN NO. 1 RELAY

C

REPLACE FAN NO. 2 RELAY

D

REPLACE FAN NO. 3 RELAY

5.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
a.

Remove the FAN NO. 2 relay from the No. 2 relay block.


b.
A375062C02
0.104,0.104 0.417,0.302 0.313,0.198 10 false *1 0.531,0.24 0.844,0.438 0.313,0.198 10 false *2
*1 No. 2 Relay Block
*2 FAN NO. 2 Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
5 (FAN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT COOLING FAN MOTOR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

6.INSPECT COOLING FAN MOTOR RH

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR RH - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR RH - BODY GROUND)
a.

Disconnect the A4 cooling fan motor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A4-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 2 RELAY - COOLING FAN MOTOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR RH - BODY GROUND)

8.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 2 RELAY - COOLING FAN MOTOR RH)
a.

Disconnect the A4 cooling fan motor RH connector.


b.

Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block.


c.
A375063C05
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.51,0.229 0.823,0.427 0.313,0.198 10 false *3 1.083,2.5 1.396,2.698 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block
*2 FAN NO. 1 Relay
*3 FAN NO. 2 Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A4-2 - 5 (FAN NO. 1 relay) Always Below 1 Ω
A4-2 - 4 (FAN NO. 2 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A4-2 or 5 (FAN NO. 1 relay) - Body ground Always 10 kΩ or higher
A4-2 or 4 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT COOLING FAN MOTOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY AND FAN NO. 2 RELAY - COOLING FAN MOTOR RH)

9.INSPECT COOLING FAN MOTOR LH

Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY AND FAN NO. 3 RELAY - COOLING FAN MOTOR LH)

NG

10.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY AND FAN NO. 3 RELAY - COOLING FAN MOTOR LH)
a.

Disconnect the A5 cooling fan motor LH connector.


b.

Remove the FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block.


c.
A375064C02
0.115,0.094 0.427,0.292 0.313,0.198 10 false *1 0.531,0.229 0.844,0.427 0.313,0.198 10 false *2 2.229,0.229 2.542,0.427 0.313,0.198 10 false *3
*1 No. 2 Engine Room Relay Block
*2 FAN NO. 2 Relay
*3 FAN NO. 3 Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A5-1 - 3 (FAN NO. 2 relay) Always Below 1 Ω
A5-2 - 5 (FAN NO. 3 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A5-1 or 3 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher
A5-2 or 5 (FAN NO. 3 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY AND FAN NO. 3 RELAY - COOLING FAN MOTOR LH)

11.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - FAN NO. 2 RELAY)
a.

Remove the FAN NO. 1 relay and FAN NO. 2 relay from the No. 2 engine room relay block.


b.
A375063C06
0.104,0.135 0.417,0.333 0.313,0.198 10 false *1 1.073,2.5 1.385,2.698 0.313,0.198 10 false *2 0.531,0.24 0.844,0.438 0.313,0.198 10 false *3
*1 No. 2 Engine Room Relay Block
*2 FAN NO. 1 Relay
*3 FAN NO. 2 Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) - 2 (FAN NO. 2 relay) Always Below 1 Ω
2 (FAN NO. 1 relay) - 1 (FAN NO. 2 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) or 2 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher
2 (FAN NO. 1 relay) or 1 (FAN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE NO. 2 RELAY BLOCK

12.INSPECT COOLING FAN RELAY (FAN NO. 1, FAN NO. 2 AND FAN NO. 3)
a.

Inspect the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay.

Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>RELAY>ON-VEHICLE INSPECTION


Result:
Result Proceed to
OK A
NG (FAN NO. 1 relay) B
NG (FAN NO. 2 relay) C
NG (FAN NO. 3 relay) D



A

13.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY, FAN NO. 2 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)

B

REPLACE FAN NO. 1 RELAY

C

REPLACE FAN NO. 2 RELAY

D

REPLACE FAN NO. 3 RELAY

13.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY, FAN NO. 2 RELAY AND FAN NO. 3 RELAY POWER SOURCE CIRCUIT)
a.

Remove the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 engine room relay block.


b.
A375057C02
0.125,0.125 0.438,0.323 0.313,0.198 10 false *1 0.552,0.24 0.865,0.438 0.313,0.198 10 false *3 2.24,0.25 2.552,0.448 0.313,0.198 10 false *4 1.094,2.521 1.406,2.719 0.313,0.198 10 false *2
*1 No. 2 Engine Room Relay Block
*2 FAN NO. 1 Relay
*3 FAN NO. 2 Relay
*4 FAN NO. 3 Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) - Body ground Always 11 to 14 V
2 (FAN NO. 2 relay) - Body ground Always 11 to 14 V
1 (FAN NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY, FAN NO. 2 RELAY AND FAN NO. 3 RELAY - ECM)

NG

14.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY, FAN NO. 2 RELAY AND FAN NO. 3 RELAY - NO. 1 INTEGRATION RELAY)
14.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY, FAN NO. 2 RELAY AND FAN NO. 3 RELAY - NO. 1 INTEGRATION RELAY)
a.

Remove the FAN NO. 1 relay, FAN NO. 2 relay and FAN NO. 3 relay from the No. 2 relay block.


b.

Remove the No. 1 integration relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the 1B No. 1 integration relay connector.


d.
A375057C02
0.125,0.125 0.438,0.323 0.313,0.198 10 false *1 0.552,0.24 0.865,0.438 0.313,0.198 10 false *3 2.24,0.25 2.552,0.448 0.313,0.198 10 false *4 1.094,2.521 1.406,2.719 0.313,0.198 10 false *2
*1 No. 2 Relay Block
*2 FAN NO. 1 Relay
*3 FAN NO. 2 Relay
*4 FAN NO. 3 Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) - 1B-4 Always Below 1 Ω
2 (FAN NO. 2 relay) - 1B-4 Always Below 1 Ω
1 (FAN NO. 3 relay) - 1B-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1 (FAN NO. 1 relay) or 1B-4 - Body ground Always 10 kΩ or higher
2 (FAN NO. 2 relay) or 1B-4 - Body ground Always 10 kΩ or higher
1 (FAN NO. 3 relay) or 1B-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY, FAN NO. 2 RELAY AND FAN NO. 3 RELAY - NO. 1 INTEGRATION RELAY)

15.INSPECT NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY)
a.

Inspect the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE NO. 1 INTEGRATION RELAY (EFI-MAIN RELAY)

16.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY POWER SOURCE CIRCUIT)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block.


b.

Disconnect the 1B No. 1 integration relay connector.


c.
A397851C01
1.542,0.323 1.875,0.573 0.333,0.25 0.104,0.083 0.417,0.281 0.313,0.198 12 false *a 1.615,0.375 1.927,0.573 0.313,0.198 10 false 1B
*a Front view of wire harness connector
(to No. 1 Integration Relay)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY POWER SOURCE CIRCUIT)

17.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block.


b.

Disconnect the 1B No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

18.CHECK HARNESS AND CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the 1B No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A38-46 (MREL) - 1B-6 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A38-46 (MREL) or 1B-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - NO. 1 INTEGRATION RELAY)