The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the radiator assembly removal/installation are shown below.
51441
1.REMOVE NO. 1 ENGINE UNDER COVER
2.DRAIN ENGINE COOLANT (for Engine)
3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
81175
4.REMOVE HEADLIGHT ASSEMBLY LH
for Halogen Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>REMOVAL
for LED Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
81135
5.REMOVE HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
G9040
6.REMOVE INVERTER WATER PUMP ASSEMBLY
52021B
7.REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY
Remove the 4 bolts and front bumper upper reinforcement sub-assembly from the vehicle.
53117C
8.REMOVE NO. 1 RADIATOR GRILLE RETAINER
16561C
9.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
10.REMOVE HOOD LOCK NUT CAP
53510
11.REMOVE HOOD LOCK ASSEMBLY
w/ Engine Hood Courtesy Switch:
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL
w/o Engine Hood Courtesy Switch:
Click hereVehicle Exterior>DOOR / HATCH>HOOD LOCK CONTROL CABLE ASSEMBLY>REMOVAL
17752
12.REMOVE NO. 2 AIR CLEANER INLET
53205
13.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Disengage the clamp to disconnect the hood control cable sub-assembly from the upper radiator support sub-assembly.
Disengage the 3 clamps to disconnect the wire harness from the horn and hood lock support assembly.
Disengage the 12 clamps to disconnect the wire harness from the upper radiator support sub-assembly and fan shroud assembly.
Disconnect the cooling fan motor RH connector and cooling fan motor LH connector.
Remove the 5 bolts and upper radiator support sub-assembly together with hood lock support sub-assembly from the vehicle.
16594
14.REMOVE NO. 2 RADIATOR AIR GUIDE
Disengage the 5 claws to remove the No. 2 radiator air guide from the radiator assembly.
16261
15.DISCONNECT NO. 1 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 1 water by-pass hose from the radiator assembly.
16264
16.DISCONNECT NO. 2 WATER BY-PASS HOSE
Disengage the 4 clamps from the fan shroud.
Slide the clip and disconnect the No. 2 water by-pass hose from the radiator assembly.
G922H
17.DISCONNECT INLET HYBRID RADIATOR HOSE
Disengage the clamp to disconnect the inlet hybrid radiator hose from the fan shroud assembly.
Slide the clip and disconnect the inlet hybrid radiator hose.
G922AA
18.DISCONNECT INLET NO. 1 INVERTER COOLING HOSE
Slide the clip and disconnect the inlet No. 1 inverter cooling hose.
16571C
19.DISCONNECT NO. 1 RADIATOR HOSE
Slide the clip and disconnect the No. 1 radiator hose.
16572D
20.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose.
G922C
21.DISCONNECT OUTLET NO. 1 INVERTER COOLING HOSE
Slide the clip and disconnect the outlet No. 1 inverter cooling hose.
G92A0A
22.REMOVE INVERTER RESERVE TANK ASSEMBLY
Disengage the clamp to disconnect the inlet hybrid water pump hose from the fan shroud assembly.
Disengage the 2 claws to remove the inverter reserve tank assembly from the fan shroud assembly.
52611
23.REMOVE FRONT BUMPER ENERGY ABSORBER
52131A
24.REMOVE FRONT BUMPER REINFORCEMENT
16595B
25.REMOVE NO. 1 RADIATOR AIR GUIDE LH
16593B
26.REMOVE NO. 1 RADIATOR AIR GUIDE RH
53398A
27.REMOVE RADIATOR LOWER SEAL LH (w/ Grille Shutter)
53398A
28.REMOVE RADIATOR LOWER SEAL RH (w/ Grille Shutter)
53019B
29.REMOVE RADIATOR SHUTTER SUB-ASSEMBLY (w/ Grille Shutter)
88703
30.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88707
31.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
88460
32.REMOVE COOLER CONDENSER ASSEMBLY
16400
33.REMOVE RADIATOR ASSEMBLY
Remove the radiator assembly with the fan shroud assembly from the vehicle body.
Disengage the 2 claws.
Disengage the 2 guides to remove the fan shroud assembly from the radiator assembly.
Do not damage the radiator assembly when removing the fan shroud assembly.
16523A
34.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16533C
35.REMOVE RADIATOR SUPPORT GROMMET
Remove the 2 radiator support grommets from the radiator assembly.
36.REMOVE RADIATOR DRAIN COCK PLUG
Remove the 2 radiator drain cock plug.
Remove the 2 O-ring from the radiator drain cock plug.