1.INSTALL HOLE PLUG
Install the 7 hole plugs to the rear suspension member sub-assembly as shown in the illustration.
51284
2.INSTALL REAR SUSPENSION MEMBER HOLE COVER
Install the 4 rear suspension member hole covers to the rear suspension member sub-assembly.
51249A
3.INSTALL REAR SUSPENSION MEMBER DAMPER
Install the rear suspension member damper to the rear suspension member sub-assembly with the 2 bolts.
48790
4.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
5.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
51206A
6.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment and Wooden Block Placement Location |
Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.
Keep supporting the rear suspension member sub-assembly until the installation has been completed.
Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.
Install the rear suspension member sub-assembly with the 2 bolts and 2 nuts.
w/ Height Control Sensor:
Engage the clamp to install the height control sensor wire harness.
48790
7.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
Temporarily install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and nut.
Insert the bolt with the threaded end facing the rear of the vehicle.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48770A
8.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
9.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
10.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
11.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
12.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48258C
13.INSTALL REAR LOWER COIL SPRING INSULATOR LH
48258B
14.INSTALL REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48231B
15.INSTALL REAR COIL SPRING LH
48231A
16.INSTALL REAR COIL SPRING RH
Perform the same procedure as for the LH side.
48812
17.INSTALL REAR STABILIZER BAR
89408C
18.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)
47319F
19.CONNECT REAR FLEXIBLE HOSE LH
Connect the rear flexible hose LH to the flexible hose bracket with the bolt.
47318F
20.CONNECT REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
21.STABILIZE SUSPENSION
48840A
22.INSTALL REAR STABILIZER LINK ASSEMBLY LH
48830D
23.INSTALL REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
24.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
25.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48740F
26.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48730F
27.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
28.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH
Install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48770A
29.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
57628C
30.INSTALL REAR FLOOR SIDE MEMBER COVER LH
57627A
31.INSTALL REAR FLOOR SIDE MEMBER COVER RH
58166
32.INSTALL FRONT FLOOR COVER LH
58165B
33.INSTALL FRONT FLOOR COVER RH
Perform the same procedure as for the LH side.
17430
34.INSTALL TAIL EXHAUST PIPE ASSEMBLY
35.INSTALL REAR WHEEL
48740F
36.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.
Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION
48730F
37.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
38.INSPECT FOR EXHAUST GAS LEAK
39.INSPECT AND ADJUST REAR WHEEL ALIGNMENT
40.PERFORM INITIALIZATION (w/ Height Control Sensor)