Based on dynamic radar cruise control system operation, the forward recognition camera provides warnings to the driver by sounding the pre-collision city buzzer.
DTC C1A4A is stored when a malfunction is detected in the pre-collision city buzzer circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A4A | Skid Control Buzzer Circuit | While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the forward recognition camera detects a malfunction in the pre-collision city buzzer circuit for approximately 0.4 seconds or more. | ·
Pre-collision city buzzer ·
Millimeter wave radar sensor assembly ·
Forward recognition camera ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the forward recognition camera, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle, and as a result, a DTC may be stored.
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Check for DTCs of the pre-collision system.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
The dynamic radar cruise control system only stores DTC C1A4A when the vehicle speed reaches 5 km/h (3 mph), however the pre-collision system stores this DTC at any vehicle speed. If DTC C1A4A is stored by the pre-collision system, perform troubleshooting of the pre-collision system first.
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
B
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Turn the power switch on (IG).
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).
Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.
Perform the Active Test according to the display on the GTS.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Radar Cruise Stop Buzzer | Skid control buzzer (stop sound) | ON or OFF | Buzzer can be heard |
| Radar Cruise Approach Alarm Buzzer | Skid control buzzer (approach sound) | ON or OFF | Buzzer can be heard |
| Tester Display |
|---|
| Radar Cruise Stop Buzzer |
| Radar Cruise Approach Alarm Buzzer |
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Front view of wire harness connector
(to pre-collision city buzzer) |
Disconnect the F54 pre-collision city buzzer connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F54-2 (IG1) - Body ground | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V |
Connect the F54 pre-collision city buzzer connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F54 pre-collision city buzzer connector.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F54-1 (BZ) - R5-8 (BZ) | Always | Below 1 Ω |
| F54-1 (BZ) or R5-8 (BZ) - Body ground | Always | 10 kΩ or higher |
Connect the R5 forward recognition camera connector.
Connect the F54 pre-collision city buzzer connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the Active Test according to the display on the GTS.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Radar Cruise Stop Buzzer | Skid control buzzer (stop sound) | ON or OFF | Buzzer can be heard |
| Radar Cruise Approach Alarm Buzzer | Skid control buzzer (approach sound) | ON or OFF | Buzzer can be heard |
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
B
Turn the power switch on (IG).
Check if the pre-collision city buzzer is sounding.
| Result | Proceed to |
|---|---|
| The pre-collision city buzzer does not sound when the power switch on (IG) | A |
| The pre-collision city buzzer sounds continuously when the power switch on (IG) | B |
A
B
Remove the pre-collision city buzzer.
Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>REMOVAL
Inspect the pre-collision city buzzer.
Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>INSPECTION
| Result | Proceed to |
|---|---|
| Pre-collision city buzzer is abnormal | A |
| Pre-collision city buzzer is normal | B |
A
B
Replace the pre-collision city buzzer.
Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the Active Test according to the display on the GTS.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Radar Cruise Stop Buzzer | Skid control buzzer (stop sound) | ON or OFF | Buzzer can be heard |
| Radar Cruise Approach Alarm Buzzer | Skid control buzzer (approach sound) | ON or OFF | Buzzer can be heard |
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
B
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Perform Forward Recognition Axis Adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the Active Test according to the display on the GTS.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Radar Cruise Stop Buzzer | Skid control buzzer (stop sound) | ON or OFF | Buzzer can be heard |
| Radar Cruise Approach Alarm Buzzer | Skid control buzzer (approach sound) | ON or OFF | Buzzer can be heard |
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
B
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
Adjust the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT