Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2018.05–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C8549  High Voltage Power Resource Internal Electronic Failure  


DESCRIPTION

The hybrid vehicle control ECU monitors the system internal operation, it will store a DTC and perform fail-safe control if it detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C8549 High Voltage Power Resource Internal Electronic Failure Battery overcurrent or overload current occurs due to a malfunction in the high-voltage circuit between the hybrid system, battery and inverter.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

HV battery junction block assembly

·

Battery voltage sensor

·

Wire harness or connector


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1C8549
·

Hybrid Battery Current

·

Hybrid Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



WIRING DIAGRAM

A311271E31
2.156,0.865 2.542,1.146 0.385,0.281 10 false 1 2.156,1.479 2.51,1.667 0.354,0.188 10 false 4 2.156,2.104 2.51,2.292 0.354,0.188 10 false 3 4.875,2.135 5.229,2.323 0.354,0.188 10 false 12 5.198,1.5 5.552,1.688 0.354,0.188 10 false IB0 4.875,0.854 5.229,1.042 0.354,0.188 10 false 6 5.167,0.854 5.521,1.042 0.354,0.188 10 false VIB 1.802,0.969 2.156,1.156 0.354,0.188 10 false VIB 4.927,1.5 5.281,1.688 0.354,0.188 10 false 5 1.813,1.594 2.167,1.781 0.354,0.188 10 false IB0 1.802,2.24 2.156,2.427 0.354,0.188 10 false GIB 5.167,2.135 5.521,2.323 0.354,0.188 10 false GIB 0.365,2.75 0.719,2.938 0.354,0.188 10 false z13 0.375,2.917 2.688,3.49 2.313,0.573 10 false HV Battery Junction Block Assembly (Battery Current Sensor) 5.01,2.76 5.365,2.948 0.354,0.188 10 false z12 5.01,2.927 6.75,3.229 1.74,0.302 10 false Battery Voltage Sensor

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position" and "Hybrid Battery Current".

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P1C8549 only is output. A
DTCs other than P1C8549 is also output. B



e.

Turn the power switch off.



A

2.READ VALUE USING GTS (HYBRID BATTERY CURRENT)

B

2.READ VALUE USING GTS (HYBRID BATTERY CURRENT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Current.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Current
50003 397 228

d.

Read the Data List.

Result:
Result Proceed to
The value of Hybrid Battery Current is between -4 A and 4 A A
Other than above B



e.

Turn the power switch off.



A

B

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery cover panel RH.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A376407N08
1.792,0.948 2.167,1.188 0.375,0.24 1.854,0.969 2.135,1.167 0.281,0.198 10 true z13

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the No. 1 hybrid battery exhaust duct.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



e.

Disconnect the battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



f.
A368052C10
2.198,2.094 2.625,2.354 0.427,0.26 2.063,3.552 2.49,3.813 0.427,0.26 1.198,1.781 1.583,2.281 true 1.771,4.031 2.365,4.208 true 0.844,2.458 1.49,2.396 true 0.865,2.094 1.5,2.271 true 0.844,4.208 1.469,4.052 true 0.854,3.583 1.448,3.76 true 0.229,0.073 0.677,0.552 0.448,0.479 10 false *a 0.344,3.01 0.917,3.542 0.573,0.531 10 false *b 2.313,2.125 2.76,2.604 0.448,0.479 10 false z12 2.167,3.594 2.615,4.073 0.448,0.479 10 false z13 0.969,1.688 1.542,2.219 0.573,0.531 10 false IB0 2.406,4.135 2.917,4.458 0.51,0.323 10 false IB0 0.615,2.385 1.188,2.917 0.573,0.531 10 false GIB 0.635,1.99 1.208,2.521 0.573,0.531 10 false VIB 0.583,4.146 1.156,4.531 0.573,0.385 10 false GIB 0.594,3.469 1.167,4 0.573,0.531 10 false VIB
*a Rear view of wire harness connector
(to Battery Voltage Sensor)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z12-5 (IB0) - z13-4 (IB0) Power switch off Below 1 Ω
z12-12 (GIB) - z13-3 (GIB) Power switch off Below 1 Ω
z12-6 (VIB) - z13-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z12-5 (IB0) or z13-4 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z12-12 (GIB) or z13-3 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z12-6 (VIB) or z13-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

As the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery.



g.

Reconnect the battery voltage sensor connector.


h.

Install the No. 1 hybrid battery exhaust duct.


i.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


j.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

4.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))

NG

4.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A368051C72
1.677,0.208 2.115,0.438 0.438,0.229 1.135,1.667 1.677,0.979 true 1.688,0.875 1.26,0.427 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.781,0.229 2.177,0.542 0.396,0.313 10 false z12 0.938,1.708 1.271,1.969 0.333,0.26 10 false GIB 0.958,0.344 1.292,0.604 0.333,0.26 10 false VIB
*a Component with harness connected
(Battery Voltage Sensor)


Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z12-6 (VIB) - z12-12 (GIB) Power switch on (IG)

NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the toyota electrical tester to 40 V when performing this test.




f.
A368051C73
1.635,0.177 2.073,0.406 0.438,0.229 1.135,1.667 1.677,0.979 true 1.76,0.865 1.177,0.281 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.76,0.198 2.156,0.51 0.396,0.313 10 false z12 0.99,1.688 1.323,1.948 0.333,0.26 10 false GIB 0.823,0.177 1.156,0.438 0.333,0.26 10 false IB0
*a Component with harness connected
(Battery Voltage Sensor)


Using a toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z12-5(IB0) - z12-12(GIB) Power switch on (IG)

NOTICE:

Be sure to set the toyota electrical tester to 4 V when performing this test.



g.

Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:

IB0 voltage - VIB Voltage / 2 = less than 0.081 V
IB0 voltage - VIB Voltage / 2 = -0.081 V or higher


Result:
Result Proceed to
Within the specified range above A
Other than above B


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 hybrid battery exhaust duct.


HINT:

When the power switch is on (IG) the actual current will be approximately 0 A. The following graph shows the relation of the actual output voltage of the battery current sensor terminal IB0 and actual current used for DTC judgment.

A382906E14
1.708,0.281 2.625,0.729 0.917,0.448 10 false Voltage 4.844,2.188 5.865,2.698 1.021,0.51 10 false Current 1.583,1.219 2.5,1.667 0.917,0.448 10 false VIB/2 3.177,2.656 4.094,3.104 0.917,0.448 10 false -4 A 3.896,2.656 4.813,3.115 0.917,0.458 10 false +4 A 3.563,2.656 4.479,3.104 0.917,0.448 10 false 0 A 0.625,2.813 3.615,3.052 2.99,0.24 10 false Battery Current Sensor Normal Range 0.615,3.073 3.604,3.313 2.99,0.24 10 false Toyota electrical tester margin of error 0.625,3.344 3.635,3.646 3.01,0.302 10 false Battery current sensor operation malfunction



A

5.REPLACE BATTERY VOLTAGE SENSOR

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

5.REPLACE BATTERY VOLTAGE SENSOR

NEXT

6.SIMULATION TEST
6.SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

d.

Drive the vehicle on urban roads for approximately 10 minutes.


e.

Turn the power switch off and wait for 2 minutes or more.


f.

Turn the power switch on (IG) and wait for 10 seconds or more.


Result:
Proceed to
NEXT



NEXT

7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

d.

Read output DTCs.


e.

Turn the power switch off.


Result:
Result Proceed to
DTCs are not output A
P1C8549 is output B



A

COMPLETED

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY