Refer to DTC P268111.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P268111
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P268172 | Engine Coolant Bypass Valve Actuator Stuck Open | The difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is 3°C (5°F) or less for 3 seconds or more (2 trip detection logic). | ·
Engine coolant level low ·
Air in cooling system (for Engine) ·
Engine coolant leak ·
Flow shutting valve (water valve) ·
Water inlet with thermostat sub-assembly (thermostat) ·
Engine coolant temperature sensor ·
No. 2 engine coolant temperature sensor ·
Engine water pump assembly |
Does not come on | DTC stored | SAE Code: P26AB |
| P268173 | Engine Coolant Bypass Valve Actuator Stuck Closed | Either of the following conditions is met for 3 seconds or more (2 trip detection logic):
·
The engine coolant temperature is less than 74°C (165°F) and the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is 6°C (11°F) or more. ·
The engine coolant temperature is 74°C (165°F) or more and the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is 15.5°C (28°F) or more. |
·
Engine coolant level low ·
Air in cooling system (for Engine) ·
Engine coolant leak ·
Flow shutting valve (water valve) ·
Water inlet with thermostat sub-assembly (thermostat) ·
Engine coolant temperature sensor ·
No. 2 engine coolant temperature sensor ·
Engine water pump assembly |
Does not come on | DTC stored | SAE Code: P26B1 |
If the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is less than 3°C (5°F) but the target operating state of the flow shutting valve (water valve) is closed, the ECM will determine that the flow shutting valve (water valve) is stuck open and store a DTC.
If the difference between the value of the engine coolant temperature sensor and No. 2 engine coolant temperature sensor is more than the threshold but the target operating state of the flow shutting valve (water valve) is open, the ECM will determine that the flow shutting valve (water valve) is stuck closed and store a DTC.
Make sure to perform this procedure when the ambient temperature is 5°C (41°F) or more, the engine coolant temperature between 5 and 40°C (41 and 104°F), and the difference between the engine coolant temperature and ambient temperature is within 10°C (18°F).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Enter the following menus: Powertrain / Engine / Data List / Coolant Water Route Switching Valve.
Start the engine and check that the value of the Data List item Coolant Water Route Switching Valve is "Close".
Warm up the engine until the value of the Data List item Coolant Water Route Switching Valve is "Open".
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P268172.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
When performing this procedure, start the engine when the coolant temperature is less than 40°C (104°F).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Start the engine.
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P268173.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
- for Lithium-ion Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
- for Lithium-ion Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY
When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.
Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P268172 or P268173 is output | A |
| DTC P268172 or P268173 and other DTCs are output | B |
If DTC P268173 and P26819C are output simultaneously, perform troubleshooting for DTC P268173 first.
If DTC P268172 and P26819C are output simultaneously, perform troubleshooting for DTC P26819C first.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P26819C
If any DTCs other than DTC P268172, P268173 or P26819C are output, perform troubleshooting for those DTCs first.
A
B
Check that the engine coolant level is between the FULL and LOW lines.
The engine coolant is not excessively low.
Make sure that there are no signs of the engine overheating.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair any engine coolant leaks.
Add engine coolant and perform air bleeding after repair.
Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P268172 or P268173 is output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Electric Water Pump.
| Tester Display |
|---|
| Activate the Electric Water Pump |
Perform the Active Test according to the display on the GTS and lightly squeeze a radiator hose by hand to check for a pulsing feeling.
Pulsing can be felt in a radiator hose.
If pulsing cannot be felt in a radiator hose, inspect the engine water pump assembly. If the impeller is damaged, replace the engine water pump assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Heater Coolant Temperature Sensor.
| Tester Display |
|---|
| Coolant Temperature |
| Heater Coolant Temperature Sensor |
Start the engine.
Read the value displayed on the GTS.
The values of Data List items Coolant Temperature and Heater Coolant Temperature Sensor change over time and do not get stuck on a certain value.
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Value of Data List item Coolant Temperature does not change) | B |
| NG (Value of Data List item Heater Coolant Temperature does not change) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up with the A/C switch and all other accessories off until the engine coolant temperature reaches 85°C (185°F).
Warm up the engine until the engine coolant temperature reaches the water inlet with thermostat sub-assembly opening temperature.
Enter the following menus: Powertrain / Engine / Active Test / Control the Engine Cooling Fan / Data List / Coolant Temperature.
| Active Test Display |
|---|
| Control the Engine Cooling Fan |
| Data List Display |
|---|
| Coolant Temperature |
Read the Data List while performing the Active Test with the engine idling.
The engine coolant temperature does not decrease to 70°C (158°F) or less.
While performing the Active Test, if the engine coolant temperature decreases to 70°C (158°F) or less, the water inlet with thermostat sub-assembly may be stuck open.
| Control the Engine Cooling Fan
(Active Test) |
Coolant Temperature
(Data List) |
Water Inlet with Thermostat Sub-assembly Operation | Proceed to |
|---|---|---|---|
| High | Higher than 70°C (158°F) | Normal | A |
| 70°C (158°F) or less | Stuck open | B |
A
B
Inspect the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
If the result of the engine coolant temperature sensor inspection differs greatly from the specified value, inspect the water inlet with thermostat sub-assembly.
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 2 engine coolant temperature sensor.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the flow shutting valve (water valve).
Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>FLOW SHUTTING VALVE>REMOVAL
When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.
Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
DTCs are not output.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Engine Water Pump Assembly |
| *2 | Impeller |
Visually inspect the impeller for damage.
The impeller is not damaged.
If the impeller is damaged, replace the engine water pump assembly.
Click hereEngine / Hybrid System>2ZR-FXE (COOLING)>WATER PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT