Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL PUMP › 2018.05–2020.08
RM32K0E _51 Engine / Hybrid System _060063 2ZR-FXE FUEL _0294218 FUEL PUMP A

2ZR-FXE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.
A398087C03
0.333,1.167 0.396,0.99 false 1.167,2.833 1.708,2.531 true 0.198,1.188 0.51,1.344 0.313,0.156 10 false *a 0.958,2.792 1.156,2.979 0.198,0.188 10 true *b
*a Protrusion
*b Notch


Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Be careful not to bend the arm of the fuel sender gauge assembly.

·

Make sure the horizontal angle of the fuel suction plate sub-assembly is less than 90°.

·

To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.


A398088C03
1.833,1.167 2.167,1.167 false 1.917,1.917 2.167,1.917 false 1.792,2.219 2.135,2.219 true 5.75,2.5 5.917,2.333 true 5.75,1.583 6.083,1.417 false 5.823,2.031 6.333,1.667 true 5.583,2.5 5.896,2.656 0.313,0.156 10 false *1 2.208,1.833 2.521,1.99 0.313,0.156 10 false *2 2.219,1.073 2.49,1.271 0.271,0.198 10 false *3 0.396,0.25 0.708,0.406 0.313,0.156 10 false *a 2.188,2.125 2.531,2.427 0.344,0.302 10 false *1 6.365,1.531 6.583,1.698 0.219,0.167 10 false *2 6.125,1.281 6.396,1.479 0.271,0.198 10 false *3
*1 Fuel Sender Gauge Assembly *2 Fuel Sub-tank Sub-assembly
*3 Fuel Suction Plate Sub-assembly - -
*a 90° - -




c.
A374369C05
1.188,1.406 0.813,0.438 0.813,0.438 2.146,0.75 true 0.292,2.719 0.917,2.719 true 0.635,0.354 0.948,0.51 0.313,0.156 10 false *a 0.115,2.646 0.427,2.802 0.313,0.156 10 false *a
*a Protrusion
V100135

Notch


Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A374358C09
0.76,0.75 1.188,0.75 true 0.781,0.365 1.292,0.365 true 2.344,0.906 2.615,0.563 2.615,0.563 2.729,0.563 true 2.563,1.177 2.771,1.573 2.771,1.573 2.865,1.573 true 2.229,2.063 2.229,1.365 true 0.948,2.938 1.771,2.938 true 1.833,2.875 2.146,3.031 0.313,0.156 10 false *a 2.927,1.521 3.24,1.677 0.313,0.156 10 false *b 2.146,2.083 2.458,2.24 0.313,0.156 10 false *c 0.604,0.302 0.917,0.458 0.313,0.156 10 false *d 0.583,0.677 0.896,0.833 0.313,0.156 10 false *c 2.792,0.5 3.104,0.656 0.313,0.156 10 false *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A374370C08
1.479,0.271 1.635,0.271 1.635,0.271 1.906,0.823 false 0.521,3.438 0.677,3.438 0.677,3.438 0.885,4.052 true 1.146,3.906 1.448,3.552 1.448,3.552 1.583,3.552 true 2.063,2.24 2.063,1.656 true 1.042,0.677 1.198,0.677 1.198,0.677 1.313,0.875 false 1.125,1.26 1.385,1.26 true 1.094,0.99 1.438,0.99 true 2.146,1.344 2.26,1.167 2.26,1.167 2.396,1.167 true 1.833,1.146 2.167,0.958 2.167,0.958 2.281,0.958 true 1.615,3.479 1.792,3.635 0.177,0.156 10 true *a 0.313,3.365 0.5,3.531 0.188,0.167 10 true *b 1.313,0.188 1.625,0.344 0.313,0.156 10 false *c 0.875,0.604 1.188,0.76 0.313,0.156 10 false *d 1.99,2.271 2.302,2.427 0.313,0.156 10 false *e 0.948,1.188 1.26,1.344 0.313,0.156 10 false *e 0.938,0.927 1.25,1.083 0.313,0.156 10 false *f 2.448,1.104 2.76,1.26 0.313,0.156 10 false *f 2.323,0.885 2.719,1.094 0.396,0.208 10 false *g
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Claw)
*f SST (Bolt)
*g Extension Bar
V100135

Tighten
V100136

Front Side of Vehicle


Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010)


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A374371C05
3.635,1.51 4.948,2.688 1.313,1.177 5.302,1.5 6.615,2.677 1.313,1.177 1.531,0.313 1.646,0.313 1.646,0.313 1.813,1 true 1.573,2.26 1.573,1.979 true 4.625,1.052 4.719,1.052 4.719,1.052 4.813,0.781 false 5.323,0.771 5.771,0.771 5.771,0.771 5.771,0.885 false 5.531,0.604 5.781,0.604 false 5.313,0.885 5.844,0.885 false 4.469,1.885 4.656,1.885 false 4.594,2.438 4.469,2.438 4.469,2.438 4.26,2 true 5.885,1.927 6.104,1.635 6.104,1.635 6.198,1.635 true 6.104,1.958 6.302,1.958 false 4.448,0.99 4.76,1.146 0.313,0.156 10 false *1 5.833,0.542 6.146,0.698 0.313,0.156 10 false *2 1.344,0.26 1.656,0.417 0.313,0.156 10 false *3 5.885,0.813 6.198,0.969 0.313,0.156 10 false *a 3.698,1.552 4.01,1.708 0.313,0.156 10 false *b 5.375,1.531 5.688,1.688 0.313,0.156 10 false *c 4.646,2.375 4.958,2.531 0.313,0.156 10 false *d 1.479,2.292 1.792,2.448 0.313,0.156 10 false *2 4.719,1.813 5.031,1.969 0.313,0.156 10 false *2 6.354,1.896 6.667,2.052 0.313,0.156 10 false *2 6.24,1.573 6.552,1.729 0.313,0.156 10 false *d
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a O-ring *b Correct
*c Incorrect *d Collar
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 77754B 4.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.

Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.


Hide 77026A 5.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.


Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the fuel pump connector.


d.

Install the rear floor service hole cover with new butyl tape.


Hide 82818G 7.INSTALL NO. 8 WIRING HARNESS PROTECTOR

a.

Install a new No. 8 wiring harness protector to the rear floor service hole cover.


Hide 71305A 8.INSTALL CENTER REAR SEATBACK HINGE SUB-ASSEMBLY

a.

Install the center rear seatback hinge sub-assembly to the vehicle body with the 2 bolts.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 73380A 9.INSTALL REAR SEAT INNER BELT ASSEMBLY

Hide 73480 10.INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 13.INSTALL REAR SEAT ASSEMBLY

Hide 14.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION