The hybrid vehicle control ECU monitors the system internal operation, it will store a DTC and perform fail-safe control if it detects the following malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P1C8549 | High Voltage Power Resource Internal Electronic Failure | Battery overcurrent or overload current occurs due to a malfunction in the high-voltage circuit between the hybrid system, battery and inverter.
(1 trip detection logic) |
·
Hybrid vehicle control ECU ·
HV battery junction block assembly ·
Battery voltage sensor ·
Wire harness or connector |
Does not come on | Master Warning: Comes on |
| DTC No. | Data List |
|---|---|
| P1C8549 | ·
Hybrid Battery Current ·
Hybrid Battery Voltage ·
VL-Voltage before Boosting ·
VH-Voltage after Boosting |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position" and "Hybrid Battery Current".
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1C8549 only is output. | A |
| DTCs other than P1C8549 is also output. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Current.
| Tester Display |
|---|
| Hybrid Battery Current |
Read the Data List.
| Result | Proceed to |
|---|---|
| The value of Hybrid Battery Current is between -4 A and 4 A | A |
| Other than above | B |
Turn the power switch off.
A
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
B
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery cover panel RH.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HV BATTERY>REMOVAL
Disconnect the z13 battery current sensor connector from the HV battery junction block assembly.
Before disconnecting the connector, check that it is not loose or disconnected.
Remove the No. 1 HV battery protector.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HV BATTERY>REMOVAL
Disconnect the z12 battery voltage sensor connector.
Before disconnecting the connector, check that it is not loose or disconnected.
| *a | Rear view of wire harness connector
(to Battery Voltage Sensor) |
| *b | Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor)) |
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z12-5 (IB0) - z13-4 (IB0) | Power switch off | Below 1 Ω |
| z12-12 (GIB) - z13-3 (GIB) | Power switch off | Below 1 Ω |
| z12-6 (VIB) - z13-1 (VIB) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z12-5 (IB0) or z13-4 (IB0) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z12-12 (GIB) or z13-3 (GIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| z12-6 (VIB) or z13-1 (VIB) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
As the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery.
Reconnect the z12 battery voltage sensor connector.
Install the No. 1 HV battery protector.
Reconnect the z13 battery current sensor connector.
Install the No. 1 HV battery cover panel RH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the No. 1 HV battery protector.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HV BATTERY>REMOVAL
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
| *a | Component with harness connected
(Battery Voltage Sensor) |
Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition |
|---|---|
| z12-6 (VIB) - z12-12 (GIB) | Power switch on (IG) |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Be sure to set the toyota electrical tester to 40 V when performing this test.
| *a | Component with harness connected
(Battery Voltage Sensor) |
Using a toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition |
|---|---|
| z12-5 (IB0) - z12-12 (GIB) | Power switch on (IG) |
Be sure to set the toyota electrical tester to 4 V when performing this test.
Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:
| IB0 voltage - VIB Voltage / 2 = less than 0.081 V |
| IB0 voltage - VIB Voltage / 2 = -0.081 V or higher |
| Result | Proceed to |
|---|---|
| Within the specified range above | A |
| Other than above | B |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the No. 1 HV battery protector.
When the power switch is on (IG) the actual current will be approximately 0 A. The following graph shows the relation of the actual output voltage of the battery current sensor terminal IB0 and actual current used for DTC judgment.
A
B
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>BATTERY VOLTAGE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data.
Drive the vehicle on urban roads for approximately 10 minutes.
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and wait for 30 seconds or more.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read output DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P1C8549 is output | B |
Turn the power switch off.
A
B