The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during HV battery removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
If the HV battery has been struck or dropped, replace it.
When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:
- Push the connector until a click sound is heard.
- Visually check and confirm that the connector is securely connected by pulling on it.
Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.
If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.
When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.
Do not touch any high voltage wire harnesses, connectors or parts with bare hands.
Hold the areas shown in the illustration and lift the HV battery.
Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.
| *a | Opening |
Do not put your hands into the openings of the HV battery.
When removing/installing/moving the HV battery assembly, make sure not to tilt it more than 80°.
Do not climb on top of or stand on the HV battery.
Do not allow any foreign matter or water to enter the HV battery.
If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
1. PRECAUTION
G3834
2.REMOVE SERVICE PLUG GRIP
82121
3.DISCONNECT ENGINE WIRE
4.REMOVE CONNECTOR COVER ASSEMBLY
5.CHECK TERMINAL VOLTAGE
6.INSTALL CONNECTOR COVER ASSEMBLY
Be sure to wear insulated gloves.
| *a | Bolt (A) |
| *b | Bolt (B) |
Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).
Do not touch the connector cover assembly waterproof seal.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Install the bolt (B).
82121
7.CONNECT ENGINE WIRE
73350C
8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
10.REMOVE REAR SEAT CUSHION LOCK HOOK
67918A
11.REMOVE REAR DOOR SCUFF PLATE LH
76974F
12.REMOVE REAR UNDER SIDE COVER LH
67917A
13.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
76973F
14.REMOVE REAR UNDER SIDE COVER RH
Use the same procedure as for the LH side.
76971G
15.REMOVE REAR UNDER COVER
Disengage the 2 clips.
Disengage the 2 guides to remove the rear under cover from the rear seat cushion leg sub-assembly.
71033
16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
Remove the 6 bolts and rear seat cushion leg sub-assembly.
G9230
17.REMOVE BATTERY COOLING BLOWER ASSEMBLY
G92N4A
18.REMOVE NO. 1 HV BATTERY COVER PANEL RH
Be sure to wear insulated gloves.
| *1 | Service Plug Grip |
| *2 | Battery Cover Lock Striker |
| *a | Projection |
| *b | Turn |
| *c | Button |
Using the service plug grip, remove the battery cover lock striker.
Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.
Remove the 3 bolts, 2 nuts and No. 1 HV battery cover panel RH from the HV battery.
821H1
19.DISCONNECT HV FLOOR UNDER WIRE
Be sure to wear insulated gloves.
| *a | Shield Ground |
Disconnect the 2 HV battery junction block assembly connectors.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Disconnect the shield ground from the HV battery.
82161
20.DISCONNECT FLOOR WIRE
Be sure to wear insulated gloves.
Disengage the clamp.
Disconnect the electric vehicle battery plug assembly connector.
Disconnect the HV battery junction block assembly connector.
G92PC
21.REMOVE NO. 1 HV BATTERY PROTECTOR
Be sure to wear insulated gloves.
Remove the clip.
Disengage the claw to remove the No. 1 HV battery protector from the HV battery.
82161
22.DISCONNECT FLOOR WIRE
Be sure to wear insulated gloves.
Disengage the clamp.
Disconnect the battery voltage sensor connector.
23.REMOVE HV BATTERY
Be sure to wear insulated gloves.
Remove the 5 bolts and HV battery from the vehicle.
Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.
To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.
Use cardboard or another similar material to protect the HV battery and vehicle body from damage.
Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.
When removing the HV battery from the vehicle, do not allow it to contact the vehicle.
When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.
Insulate the disconnected terminals or connectors with insulating tape.
If the HV battery has been struck or dropped, replace it.
G920L
24.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY
Be sure to wear insulated gloves and protective goggles.
Remove the 7 bolts, 6 nuts and upper No. 1 hybrid battery cover sub-assembly from the HV battery.
G92Q1
25.REMOVE NO. 1 HV BATTERY SHIELD PANEL
89892A
26.REMOVE BATTERY VOLTAGE SENSOR
G92Z2
27.REMOVE HYBRID BATTERY TERMINAL BLOCK
G92J5
28.REMOVE NO. 1 HYBRID BATTERY PACKING
Be sure to wear insulated gloves and protective goggles.
Disengage the 2 claws and remove the No. 1 hybrid battery packing from the HV battery.
29.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY
G920Q
30.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY
G92D1
31.REMOVE NO. 1 HYBRID BATTERY INTAKE DUCT