Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › BATTERY VOLTAGE SENSOR › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404416 BATTERY VOLTAGE SENSOR A

M20A-FXS HYBRID / BATTERY CONTROL  BATTERY VOLTAGE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during battery voltage sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision System
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



NOTICE:
·

The type of battery voltage sensor to be used varies depending on the vehicle model.

·
A401803C01
2.052,0.823 2.958,0.823 true 2.979,0.719 3.292,0.875 0.313,0.156 10 false *a
*a Bluish green Label


The type of battery voltage sensor can be confirmed by the color of the label.

·

If the wrong type of battery voltage sensor is installed, the power switch cannot be turned on (READY).

·

After installing the battery voltage sensor, perform the following to check that the power switch can be turned on (READY).

-

Turn the power switch on (READY).

-

Turn the power switch off and wait for 30 seconds or more.

-

Turn the power switch on (READY) again.




PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 73350C 8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 11.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 12.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 13.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 14.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 71033 16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G9230 17.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N4A 18.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 19.DISCONNECT HV FLOOR UNDER WIRE

Hide G92PC 21.REMOVE NO. 1 HV BATTERY PROTECTOR

Hide G920L 23.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A443780

Remove the 5 bolts.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

If the HV battery has been struck or dropped, replace it.




b.
A443781

Move the HV battery toward the front of the vehicle.


c.
A443782

Remove the 7 bolts, 6 nuts and upper No. 1 hybrid battery cover sub-assembly from the HV battery.


Hide G92Q1 24.REMOVE NO. 1 HV BATTERY SHIELD PANEL

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A443783

Disengage the clamp.


b.

Disconnect the battery voltage sensor connector.


c.
A443784

Remove the bolt and 2 nuts.


d.
A443785C01
0.74,1.979 0.99,1.979 0.99,1.979 1.271,1.688 true 1.646,0.354 1.896,0.354 1.896,0.354 2.385,1.031 true 0.542,1.865 0.729,2.052 0.188,0.188 10 true *1 1.458,0.25 1.646,0.427 0.188,0.177 10 true *2
*1 No. 1 HV Battery Shield Panel
*2 Rear Hybrid Battery Shield Sub-assembly
V100135

Pull Back


Pull back the rear hybrid battery shield sub-assembly and remove the No. 1 HV battery shield panel from the HV battery.

HINT:

Pull back the rear hybrid battery shield sub-assembly until it is separated from the stud bolt of the No. 1 HV battery shield panel.



Hide 89892A 25.REMOVE BATTERY VOLTAGE SENSOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A443786

Disconnect the battery voltage sensor connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.
A443787

Remove the bolt and battery voltage sensor from the HV battery.

NOTICE:

If the battery voltage sensor has been struck or dropped, replace it.