Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › FRAME WIRE › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404421 FRAME WIRE A

M20A-FXS HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Perform steering sensor zero point calibration (Click here)
Initialize back door lock Power door lock control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 73350C 8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 11.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 12.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 13.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 14.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 71033 16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N4A 17.REMOVE NO. 1 HV BATTERY COVER PANEL RH

Hide 821H1 18.DISCONNECT HV FLOOR UNDER WIRE

Hide 57627A 19.REMOVE REAR FLOOR SIDE MEMBER COVER RH

Hide 58165B 20.REMOVE FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.

Click hereEngine / Hybrid System>M20A-FXS (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL


Hide 51201 21.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 821H1 22.REMOVE HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A444054

Remove the 2 nuts.


b.

Remove the 3 clamps.

A444055

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



c.
A444056

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


d.

for LHD:

i.
A444059

Remove the nut.


ii.

Disconnect the connector.


iii.

Disengage the 2 clamps.



e.

for RHD:

i.
A444058

Disconnect the connector.


ii.

Remove the 2 nuts.


iii.

Disengage the 3 clamps.



f.
A444057N01
2.74,1.073 2.896,1.271 0.156,0.198 10 true A 0.531,0.51 0.688,0.708 0.156,0.198 10 true B

Remove the clamp (A).


g.

Disengage the clamp (B) to remove the HV floor under wire.