Home › General › MAINTENANCE › P711 HYBRID TRANSAXLE FLUID › from 2019.09
RM32K0E _V1 General _059911 MAINTENANCE _0404818 P711 HYBRID TRANSAXLE FLUID A

MAINTENANCE  P711 HYBRID TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 43409E 3.SEPARATE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
C463495

Remove the 3 bolts form the drive shaft heat insulator sub-assembly.

HINT:

Not remove the drive shaft heat insulator sub-assembly.



b.
C463497C01
1.042,1.583 1.406,1.583 true 0.823,1.5 1.042,1.698 0.219,0.198 10 true *1
*1 Filler Plug
V113147

Move in this Direction


Separate the drive shaft heat insulator sub-assembly from the cylinder block sub-assembly.

HINT:

Move the drive shaft heat insulator sub-assembly to the position where the filler plug of the hybrid vehicle transaxle assembly can be removed.



Hide 4.REPLACE HYBRID TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.
C377438

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly. [#2]


c.
C377439

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid. [#3]


d.

Using a 10 mm hexagon socket wrench, temporarily install the drain plug and gasket to the hybrid vehicle transaxle assembly. [#4]

HINT:

Reuse the old gasket as the drain plug will be removed again.



e.
C377440C01
2.385,1.094 2.5,0.823 2.5,0.823 2.635,0.823 false 2.698,0.74 2.938,0.948 0.24,0.208 10 false *a 3.146,1.708 3.375,1.917 0.229,0.208 10 false *b
*a Filler Nozzle
*b 0 to 10 mm (0 to 0.394 in.)


Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. [#5]

NOTICE:
·

Use Toyota Genuine ATF WS.

·

Be sure to fully insert the filler nozzle into the filler plug opening.

·

Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

An insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.




f.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly. [#6]

HINT:

Reuse the old gasket as the filler plug will be removed again.



g.

Lower the vehicle. [#7]


h.

Put the engine in Inspection Mode (Maintenance Mode). [#8]

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Idle the engine for 30 seconds with the power switch on (READY). [#9]


j.

Turn the power switch off. [#10]


k.

Repeat steps [#1] to [#10].


l.

Repeat steps [#1] to [#3].


m.

Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


n.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 43409E 7.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.
C463496C01
0.427,0.938 0.979,1.135 0.552,0.198 10 true 1 (*a), 3 2.531,0.885 2.646,1.063 0.115,0.177 10 true 2 0.969,0.469 1.083,0.656 0.115,0.188 10 true 4
*a Temporarily Tighten


Install the drive shaft heat insulator sub-assembly to the cylinder block sub-assembly with the 3 bolts in the order shown in the illustration.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 51410 9.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY