Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL INJECTOR › from 2020.08
RM32K0E _51 Engine / Hybrid System _060063 2ZR-FXE FUEL _0294216 FUEL INJECTOR A

2ZR-FXE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

SFI system:

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A374342C02
0.573,0.479 0.938,0.479 false 2.229,1.427 2.458,1.063 2.458,1.063 2.583,1.063 false 0.396,0.417 0.708,0.573 0.313,0.156 10 false *1 2.646,1 2.958,1.156 0.313,0.156 10 false *2
*1 O-ring
*2 Injector Vibration Insulator


Apply a light coat of gasoline or spindle oil to new injector vibration insulators and new O-rings, and then install one to each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil where the fuel delivery pipe sub-assembly contacts each O-ring.


c.
A374343C01
1.26,0.052 1.573,0.208 0.313,0.156 10 false *a
*a Turn
V100135

Push


While turning the fuel injector assembly left and right, install it to the fuel delivery pipe sub-assembly.

NOTICE:
·

Do not damage the fuel injector assembly or O-ring.

·

Make sure that the O-ring is not twisted or moved out of place when installing the fuel injector assembly.

·

After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.



HINT:

Use the same procedure to install the other fuel injector assemblies.



Hide 23807V 2.INSTALL NO. 1 DELIVERY PIPE SPACER

a.
A374558C02
1.521,1.229 1.833,1.385 0.313,0.156 10 false *a 1.521,1.958 1.833,2.115 0.313,0.156 10 false *b
*a Fuel Delivery Pipe Sub-assembly Side
*b Cylinder Head Sub-assembly Side


Install the 2 No. 1 delivery pipe spacers to the cylinder head sub-assembly.

NOTICE:

Install the No. 1 delivery pipe spacers in the correct direction.



Hide 23807 3.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.

·

Check that the fuel injector assemblies turn smoothly after installing the fuel delivery pipe sub-assembly.




b.

Install the clamp of the fuel delivery pipe sub-assembly to the cylinder head sub-assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23901 4.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the fuel pipe clamp to the fuel tube connector and close the cover of the fuel pipe clamp.


Hide 82121 5.CONNECT ENGINE WIRE

a.

Engage the clamp to connect the engine wire.


b.

Install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the 4 fuel injector assembly connectors.


Hide 12262 6.CONNECT NO. 2 VENTILATION HOSE

a.

Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 25601L 7.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 9. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

SFI system:

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION