The millimeter wave radar sensor assembly receives vehicle specification information from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU via the CAN communication line. If the millimeter wave radar sensor assembly cannot confirm the vehicle specification information sent from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU, the millimeter wave radar sensor assembly stores DTC U032251.
The millimeter wave radar sensor assembly receives vehicle specification information from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU via the CAN communication line. If the vehicle specification information stored in the millimeter wave radar sensor assembly does not match the vehicle specification information sent from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU, the millimeter wave radar sensor assembly stores DTC U032257.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U032251 | Software Incompatibility with Body Control Module Not Programmed | The millimeter wave radar sensor assembly cannot confirm the vehicle specification information sent from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU. | ·
Hybrid Control System ·
Main Body ECU (Multiplex Network Body ECU) ·
Hybrid Vehicle Control ECU ·
Millimeter Wave Radar Sensor Assembly |
| U032257 | Software Incompatibility with Body Control Module Invalid/Incompatible Software Component | The vehicle specification information stored in the millimeter wave radar sensor assembly does not match the vehicle specification information sent from the main body ECU (multiplex network body ECU) and hybrid vehicle control ECU. | ·
Hybrid Control System ·
Main Body ECU (Multiplex Network Body ECU) ·
Hybrid Vehicle Control ECU ·
Millimeter Wave Radar Sensor Assembly |
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
Check for DTCs of main body ECU (multiplex network body ECU).
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Using the GTS, perform a health check.
ECUs other than the millimeter wave radar sensor assembly do not output specification information mismatch DTCs related to the main body ECU (multiplex network body ECU)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Check that the main body ECU (multiplex network body ECU) that is installed is a Toyota genuine part.
The main body ECU (multiplex network body ECU) that is installed is a Toyota genuine part
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Check for DTCs of hybrid control system.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
for 2ZR-FXE (for NICKEL METAL HYDRIDE BATTERY): Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>DIAGNOSTIC TROUBLE CODE CHART
for 2ZR-FXE (for LITHIUM-ION BATTERY): Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, perform a health check.
ECUs other than the millimeter wave radar sensor assembly do not output specification information mismatch DTCs related to the hybrid vehicle control ECU.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2ZR-FXE: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
for M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
Check that the hybrid vehicle control ECU that is installed is a Toyota genuine part.
The hybrid vehicle control ECU that is installed is a Toyota genuine part
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2ZR-FXE: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
for M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B