Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › FRAME WIRE › from 2020.08
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404382 FRAME WIRE A

2ZR-FXE HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1 The vehicle height changes because of suspension or tire replacement.

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Suspension, tires, etc.*1
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

for NICKEL METAL HYDRIDE BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for LITHIUM-ION BATTERY:

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 82121 3.DISCONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A391963

Move each lock lever as shown in the illustration and disconnect the 2 inverter with converter assembly connectors.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connector.

·

Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.

·

Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.

·

Insulate the disconnected terminals with insulating tape.




b.
A391980

Remove the bolt.


c.

Disengage the 2 clamps and disconnect the engine wire.


Hide 8.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 9.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 10.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 11.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 12.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 13.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 821H1 17.DISCONNECT FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A443722C02
0.792,1.521 1.219,1.521 true 0.813,3.844 1.24,3.844 true 0.021,0.26 0.271,0.469 0.25,0.208 12 true *A 0.031,2.583 0.281,2.813 0.25,0.229 12 true *B 0.594,1.417 0.802,1.583 0.208,0.167 10 true *a 0.625,3.74 0.833,3.906 0.208,0.167 10 true *a
*A for NICKEL METAL HYDRIDE BATTERY
*B for LITHIUM-ION BATTERY
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.


b.

Disconnect the shield ground from the HV battery.


Hide 57627A 18.REMOVE REAR FLOOR SIDE MEMBER COVER RH

Hide 58165B 19.REMOVE FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.

Click hereEngine / Hybrid System>M20A-FXS (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL


Hide 51201 20.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 821H1 21.REMOVE FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected connectors with insulating tape.


a.
A391981

Remove the 2 nuts.


b.

Remove the 3 clamps.

A391982

NOTICE:

If the clamps are removed forcibly, the stud bolts may be damaged.



c.
A391983

Disengage the grommet and pull out the HV floor under wire from the floor panel hole.


d.
A391984C01
0.083,0.177 0.354,0.396 0.271,0.219 12 true *A 0.844,1.188 1.042,1.385 0.198,0.198 10 true A 2.948,1.313 3.146,1.51 0.198,0.198 10 true B 0.104,2.573 0.375,2.792 0.271,0.219 12 true *B 2.875,3.792 3.073,3.99 0.198,0.198 10 true B 1.021,3.646 1.219,3.844 0.198,0.198 10 true A
*A for LHD
*B for RHD


Remove the clamp (A).


e.

Disengage the clamp (B) to remove the HV floor under wire.