Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 5 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)

·

Central gateway ECU (network gateway ECU)

·

Combination meter assembly

·

Air conditioning amplifier assembly

·

Headlight ECU sub-assembly LH

(for LED Headlight)

·

No. 3 CAN junction connector



WIRING DIAGRAM

C366150E09
1.323,0.729 1.938,0.927 0.615,0.198 10 false CANH 1.323,1.26 1.938,1.458 0.615,0.198 10 false CANL 1.844,0.615 2.156,0.813 0.313,0.198 10 false 24 1.844,1.156 2.156,1.354 0.313,0.198 10 false 23 0.708,1.635 1.875,1.854 1.167,0.219 10 false A95*2, A100*3 0.708,1.802 2.885,1.99 2.177,0.188 10 false Headlight ECU Sub-assembly LH*1 2.896,0.615 3.052,0.813 0.156,0.198 10 false 3 2.823,1.156 3.135,1.354 0.313,0.198 10 false 14 4.177,0.615 4.333,0.813 0.156,0.198 10 false 6 4.177,1.156 4.49,1.354 0.313,0.198 10 false 17 4.958,0.615 5.271,0.813 0.313,0.198 10 false 15 4.958,1.156 5.271,1.354 0.313,0.198 10 false 16 5.302,0.615 5.917,0.813 0.615,0.198 10 false CA5H 5.302,1.156 5.917,1.354 0.615,0.198 10 false CA5L 5.906,0.99 6.458,1.198 0.552,0.208 10 false 120 Ω 5.167,1.635 5.625,1.833 0.458,0.198 10 false F74 5.156,1.792 7.104,2.156 1.948,0.365 10 false Central Gateway ECU (Network Gateway ECU) 1.844,2.76 2,2.958 0.156,0.198 10 false 1 1.844,3.292 2,3.49 0.156,0.198 10 false 2 1.323,2.875 1.938,3.073 0.615,0.198 10 false CANH 1.323,3.406 1.938,3.604 0.615,0.198 10 false CANL 0.708,3.781 1.021,3.979 0.313,0.198 10 false F1 0.698,3.948 2.5,4.323 1.802,0.375 10 false Certification ECU (Smart Key ECU Assembly) 2.896,2.76 3.052,2.958 0.156,0.198 10 false 5 4.177,2.76 4.333,2.958 0.156,0.198 10 false 4 2.823,3.292 3.135,3.49 0.313,0.198 10 false 16 4.177,3.292 4.49,3.49 0.313,0.198 10 false 15 4.958,2.76 5.271,2.958 0.313,0.198 10 false 11 4.958,3.292 5.271,3.49 0.313,0.198 10 false 12 5.24,2.865 5.854,3.063 0.615,0.198 10 false CANH 5.24,3.396 5.854,3.594 0.615,0.198 10 false CANL 5.167,3.781 5.625,3.979 0.458,0.198 10 false F73 5.167,3.958 6.729,4.333 1.563,0.375 10 false Air Conditioning Amplifier Assembly 0.656,5.281 1.208,5.49 0.552,0.208 10 false 120 Ω 1.281,4.896 1.896,5.094 0.615,0.198 10 false CANH 1.281,5.427 1.896,5.625 0.615,0.198 10 false CANL 1.844,4.896 2.156,5.094 0.313,0.198 10 false 32 1.844,5.427 2.156,5.625 0.313,0.198 10 false 31 0.521,5.927 0.833,6.125 0.313,0.198 10 false F4 0.51,6.094 2.333,6.333 1.823,0.24 10 false Combination Meter Assembly 0.271,6.635 1.781,6.823 1.51,0.188 10 false *1: for LED Headlight 2.896,4.896 3.052,5.094 0.156,0.198 10 false 1 4.177,4.896 4.333,5.094 0.156,0.198 10 false 2 2.823,5.427 3.135,5.625 0.313,0.198 10 false 12 4.177,5.427 4.49,5.625 0.313,0.198 10 false 13 3.031,5.927 3.646,6.125 0.615,0.198 10 false F114 3.031,6.094 4.302,6.438 1.271,0.344 10 false No. 3 CAN Junction Connector 4.958,5.427 5.271,5.625 0.313,0.198 10 false 13 4.958,4.896 5.271,5.094 0.313,0.198 10 false 14 5.24,5.01 5.854,5.208 0.615,0.198 10 false CANH 5.24,5.542 5.854,5.74 0.615,0.198 10 false CANL 5.177,5.927 5.635,6.125 0.458,0.198 10 false F15 5.167,6.094 6.802,6.479 1.635,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 0.271,6.979 1.781,7.167 1.51,0.188 10 false *2: for TMMT Made 0.271,7.333 1.781,7.521 1.51,0.188 10 false *3: for TMC Made

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425191C43
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 6.323,1.198 5.688,1.646 true 1.125,2.615 1.51,2.063 true 1.135,1.292 1.521,1.865 true 1.094,1.604 1.396,1.854 true 1.177,1 1.635,1.854 true 1.26,0.729 1.75,1.854 true 2.76,1.146 1.885,1.854 true 2.802,1.448 2,1.854 true 1.083,2.302 1.385,2.063 true 1.219,2.948 1.646,2.063 true 1.313,3.24 1.76,2.063 true 2.656,2.635 1.885,2.063 true 2.833,2.354 2.021,2.063 true 0.531,1.49 1.448,1.688 0.917,0.198 10 false CANH*b 6.375,1.073 6.771,1.344 0.396,0.271 10 false CG 5.625,1.031 6.292,1.302 0.667,0.271 10 false F144 1.833,1.115 2.5,1.385 0.667,0.271 10 false F114 0.542,2.219 1.458,2.417 0.917,0.198 10 false CANL*b 0.146,0.125 1.063,0.323 0.917,0.198 10 false *a 4.708,0.146 5.625,0.344 0.917,0.198 10 false *1 0.583,2.531 1.5,2.729 0.917,0.198 10 false CANL*c 0.667,2.875 1.583,3.073 0.917,0.198 10 false CANL*d 0.76,3.188 1.677,3.385 0.917,0.198 10 false CANL*e 0.573,1.167 1.49,1.365 0.917,0.198 10 false CANH*c 0.615,0.875 1.531,1.073 0.917,0.198 10 false CANH*d 0.719,0.552 1.635,0.75 0.917,0.198 10 false CANH*e 2.833,1.042 3.75,1.24 0.917,0.198 10 false CANH*f 2.906,1.333 3.823,1.531 0.917,0.198 10 false CANH*g 2.896,2.271 3.813,2.469 0.917,0.198 10 false CANH*g 2.74,2.573 3.656,2.771 0.917,0.198 10 false CANH*f
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Combination Meter Assembly
*c to Main Body ECU (Multiplex Network Body ECU) *d to Headlight ECU Sub-assembly LH
(for LED Headlight)
*e to Air Conditioning Amplifier Assembly *f to Certification ECU (Smart Key ECU Assembly)
*g to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F114-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Combination meter assembly
F114-12 (CANL) - F144-4 (CG)
F114-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
F114-13 (CANL) - F144-4 (CG)
F114-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Headlight ECU sub-assembly LH*1
F114-14 (CANL) - F144-4 (CG)
F114-4 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
F114-15 (CANL) - F144-4 (CG)
F114-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)
F114-16 (CANL) - F144-4 (CG)
F114-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F114-17 (CANL) - F144-4 (CG)


*1: for LED Headlight



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C425191C44
5.5,1 6,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 6.406,1.24 5.698,1.635 true 1.573,2.49 2,2.063 true 1.49,1.365 2,1.865 true 0.896,1.26 1.813,1.458 0.917,0.198 10 false CANH*b 1,2.427 1.917,2.625 0.917,0.198 10 false CANL*b 1.833,1.115 2.479,1.313 0.646,0.198 10 false F114 5.583,1.031 6.229,1.229 0.646,0.198 10 false F144 6.448,1.135 7.094,1.333 0.646,0.198 10 false CG 0.135,0.125 1.052,0.323 0.917,0.198 10 false *a 4.583,0.146 5.5,0.344 0.917,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F114-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F114-17 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C425196C11
5.083,0.5 5.583,0.75 0.5,0.25 1.667,0.417 2.167,0.667 0.5,0.25 5.833,0.771 5.25,1.167 true 2.052,1.427 1.5,0.667 true 2.667,0.667 2.135,1.438 true 1.104,0.51 1.719,0.708 0.615,0.198 10 false CA5L 2.708,0.51 3.323,0.708 0.615,0.198 10 false CA5H 1.781,0.458 2.396,0.656 0.615,0.198 10 false F74 5.167,0.542 5.781,0.74 0.615,0.198 10 false F144 4.042,0.083 4.656,0.281 0.615,0.198 10 false *1 0.125,0.083 0.74,0.281 0.615,0.198 10 false *a 5.885,0.656 6.5,0.854 0.615,0.198 10 false CG
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-15 (CA5H) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-16 (CA5L) - F144-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR