Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2020.08–2021.09
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A371654C03
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

for M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

for 2ZR-FXE with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

for 2ZR-FXE with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR (w/o Blind Spot Monitor System)


a.

Check the No. 1 CAN junction connector. (for LHD)

i.

Connection diagram

C328881C37
3.292,0.365 3.75,0.615 0.458,0.25 1.635,1.177 2.083,1.417 true 1.688,0.771 2.396,1.406 true 1.594,1.875 2.094,1.646 true 1.854,2.219 2.427,1.646 true 4.74,1.406 5.448,0.708 true 4.75,1.646 5.51,2.24 true 5.094,1.406 5.656,1.042 true 5.073,1.646 5.719,1.896 true 1.813,0.448 2.74,1.406 true 2.177,2.49 2.75,1.646 true 0.229,0.198 0.531,0.448 0.302,0.25 10 false *a 3.354,0.406 3.75,0.677 0.396,0.271 10 false F111 1.083,1.073 1.708,1.344 0.625,0.271 10 false CANH*b 1.125,0.667 1.75,0.938 0.625,0.271 10 false CANH*c 1.052,1.792 1.677,2.063 0.625,0.271 10 false CANL*b 1.313,2.125 1.938,2.396 0.625,0.271 10 false CANL*c 5.573,2.177 6.198,2.448 0.625,0.271 10 false CANL*e 5.51,0.604 6.135,0.875 0.625,0.271 10 false CANH*e 5.698,0.906 6.323,1.177 0.625,0.271 10 false CANH*e 5.771,1.823 6.396,2.094 0.625,0.271 10 false CANL*e 1.25,0.333 2.167,0.531 0.917,0.198 10 false CANH*d 1.656,2.396 2.573,2.594 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Central Gateway ECU (Network Gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F111-1 (CANH) SB Clearance Warning ECU Assembly*1
(for Bus 1)
F111-11 (CANL) GR
F111-2 (CANH) R Forward recognition camera*2
(for Bus 1)
F111-12 (CANL) GR
F111-3 (CANH) G Millimeter wave radar sensor assembly*2
(for Bus 1)
F111-13 (CANL) GR
F111-9 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 1)
F111-19 (CANL) GR
F111-10 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
F111-20 (CANL) GR

*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense




b.

Check the No. 1 CAN junction connector. (for RHD)

i.

Connection diagram

C392556C37
3.292,0.365 3.75,0.615 0.458,0.25 1.948,0.938 2.729,1.417 true 2.208,0.604 3.042,1.427 true 1.906,1.906 2.708,1.656 true 2.188,2.229 3.021,1.656 true 3.99,1.438 4.979,0.604 true 4.01,1.646 5,2.219 true 4.333,1.417 5.333,0.979 true 4.344,1.667 5.354,1.917 true 2.677,0.396 3.344,1.427 true 2.844,2.385 3.354,1.635 true 0.229,0.198 0.531,0.448 0.302,0.25 10 false *a 3.354,0.406 3.75,0.677 0.396,0.271 10 false F164 1.375,0.865 2,1.135 0.625,0.271 10 false CANH*b 1.646,0.521 2.271,0.792 0.625,0.271 10 false CANH*c 1.375,1.813 2,2.083 0.625,0.271 10 false CANL*b 1.656,2.156 2.281,2.427 0.625,0.271 10 false CANL*c 5.052,0.521 5.677,0.792 0.625,0.271 10 false CANH*e 5.427,1.854 6.052,2.125 0.625,0.271 10 false CANL*e 2.125,0.26 3.042,0.458 0.917,0.198 10 false CANH*d 2.302,2.354 3.219,2.552 0.917,0.198 10 false CANL*d 5.052,2.219 5.677,2.49 0.625,0.271 10 false CANL*e 5.417,0.896 6.042,1.167 0.625,0.271 10 false CANH*e
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Parking Assist ECU
(w/ Panoramic View Monitor System)
*f to Central Gateway ECU (Network Gateway ECU)



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F164-1 (CANH) SB Clearance Warning ECU Assembly*1
(for Bus 1)
F164-7 (CANL) GR
F164-2 (CANH) R Forward recognition camera*2
(for Bus 1)
F164-8 (CANL) GR
F164-3 (CANH) G Millimeter wave radar sensor assembly*2
(for Bus 1)
F164-9 (CANL) GR
F164-4 (CANH) L Parking assist ECU*3
(for Bus 1)
F164-10 (CANL) GR
F164-5 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 1)
F164-11 (CANL) GR
F164-6 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
F164-12 (CANL) GR

*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense

*3: w/ Panoramic View Monitor System





NO. 1 CAN JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


a.

Check the No. 1 CAN junction connector. (for LHD)

i.

Connection diagram

C328881C38
3.292,0.365 3.75,0.615 0.458,0.25 1.635,1.177 2.083,1.417 true 1.688,0.771 2.396,1.406 true 1.594,1.875 2.094,1.646 true 1.854,2.219 2.427,1.646 true 4.74,1.406 5.448,0.708 true 4.75,1.646 5.51,2.24 true 5.094,1.406 5.656,1.042 true 5.073,1.646 5.719,1.896 true 1.813,0.448 2.74,1.406 true 2.177,2.49 2.75,1.646 true 0.229,0.198 0.531,0.448 0.302,0.25 10 false *a 3.354,0.406 3.75,0.677 0.396,0.271 10 false F111 1.083,1.073 1.708,1.344 0.625,0.271 10 false CANH*b 1.125,0.667 1.75,0.938 0.625,0.271 10 false CANH*c 1.052,1.792 1.677,2.063 0.625,0.271 10 false CANL*b 1.313,2.125 1.938,2.396 0.625,0.271 10 false CANL*c 5.573,2.177 6.198,2.448 0.625,0.271 10 false CANL*e 5.51,0.604 6.135,0.875 0.625,0.271 10 false CANH*e 5.698,0.906 6.323,1.177 0.625,0.271 10 false CANH*f 5.771,1.823 6.396,2.094 0.625,0.271 10 false CANL*f 1.25,0.333 2.167,0.531 0.917,0.198 10 false CANH*d 1.656,2.396 2.573,2.594 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to No. 6 CAN Junction Connector *f to Central Gateway ECU (Network Gateway ECU)



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F111-1 (CANH) SB Clearance Warning ECU Assembly*1
(for Bus 1)
F111-11 (CANL) GR
F111-2 (CANH) R Forward recognition camera*2
(for Bus 1)
F111-12 (CANL) GR
F111-3 (CANH) G Millimeter wave radar sensor assembly*2
(for Bus 1)
F111-13 (CANL) GR
F111-9 (CANH) B No. 6 CAN junction connector
(for Bus 1)
F111-19 (CANL) GR
F111-10 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
F111-20 (CANL) GR

*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense




b.

Check the No. 1 CAN junction connector. (for RHD)

i.

Connection diagram

C392556C35
3.292,0.365 3.75,0.615 0.458,0.25 2.208,0.604 3.042,1.427 true 2.49,0.281 3.375,1.427 true 2.188,2.229 3.021,1.656 true 2.5,2.531 3.344,1.667 true 3.99,1.438 4.979,0.604 true 4.01,1.646 5,2.219 true 1.979,0.948 2.656,1.458 true 2,1.781 2.677,1.604 true 4.375,1.625 5.021,1.854 true 4.375,1.458 4.979,1.188 true 0.229,0.198 0.531,0.448 0.302,0.25 10 false *a 3.354,0.406 3.75,0.677 0.396,0.271 10 false F164 1.615,0.521 2.24,0.792 0.625,0.271 10 false CANH*c 1.927,0.188 2.552,0.458 0.625,0.271 10 false CANH*d 1.646,2.156 2.271,2.427 0.625,0.271 10 false CANL*c 1.948,2.469 2.552,2.677 0.604,0.208 10 false CANL*d 5.063,0.521 5.688,0.792 0.625,0.271 10 false CANH*e 5.083,2.188 5.708,2.458 0.625,0.271 10 false CANL*e 5.115,1.771 5.74,2.042 0.625,0.271 10 false CANL*f 5.073,1.115 5.698,1.385 0.625,0.271 10 false CANH*f 1.396,0.833 2.021,1.104 0.625,0.271 10 false CANH*b 1.427,1.688 2.052,1.958 0.625,0.271 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Parking Assist ECU
(w/ Panoramic View Monitor System)
*f to No. 6 CAN Junction Connector
*g to Central Gateway ECU (Network Gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F164-1 (CANH) SB Clearance Warning ECU Assembly*1
(for Bus 1)
F164-7 (CANL) GR
F164-2 (CANH) R Forward recognition camera*2
(for Bus 1)
F164-8 (CANL) GR
F164-3 (CANH) G Millimeter wave radar sensor assembly*2
(for Bus 1)
F164-9 (CANL) GR
F164-4 (CANH) L Parking assist ECU*3
(for Bus 1)
F164-10 (CANL) GR
F164-5 (CANH) B No. 6 CAN junction connector
(for Bus 1)
F164-11 (CANL) GR
F164-6 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
F164-12 (CANL) GR

*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense

*3: w/ Panoramic View Monitor System





NO. 2 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C425784C01
3.333,1.083 3.833,1.333 0.5,0.25 2.667,1.25 3.292,1.844 true 3.479,1.844 2.75,0.917 true 3.333,2.073 2.833,2.667 true 3.469,2.073 3,3 true 3.615,1.875 4.479,1.052 true 3.583,2.052 4.448,2.948 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.104,1.156 3.021,1.354 0.917,0.198 10 false CANH*b 2.188,0.823 3.104,1.021 0.917,0.198 10 false CANH*c 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.292,2.615 3.208,2.813 0.917,0.198 10 false CANL*b 2.49,3 3.406,3.198 0.917,0.198 10 false CANL*c 4.563,0.958 5.479,1.156 0.917,0.198 10 false CANH*d 4.51,2.844 5.427,3.042 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM
*c to Brake Booster with Master Cylinder Assembly *d No. 6 CAN junction connector



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F113-4 (CANH) GR ECM
(for Bus 2)
F113-15 (CANL) P
F113-5 (CANH) LG Brake booster with master cylinder assembly
(for Bus 2)
F113-16 (CANL) P
F113-6 (CANH) R No. 6 CAN junction connector
F113-17 (CANL) P




NO. 2 CAN JUNCTION CONNECTOR (for RHD without LITHIUM-ION BATTERY)


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C366168C93
3.333,1.083 3.833,1.333 0.5,0.25 2.667,1.583 3.042,1.844 true 2.667,1.333 3.167,1.844 true 3.292,1.823 2.667,1.083 true 3.052,2.073 2.75,2.333 true 3.188,2.073 2.833,2.583 true 3.313,2.073 3,2.833 true 3.604,2.073 4.26,3.021 true 3.583,1.854 4.458,1.104 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.094,1.479 3.01,1.677 0.917,0.198 10 false CANH*b 2.104,1.219 3.021,1.417 0.917,0.198 10 false CANH*c 2.094,0.969 3.01,1.167 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.198,2.229 3.115,2.427 0.917,0.198 10 false CANL*b 2.302,2.49 3.219,2.688 0.917,0.198 10 false CANL*c 2.458,2.75 3.375,2.948 0.917,0.198 10 false CANL*d 4.531,1.021 5.448,1.219 0.917,0.198 10 false CANH*e 4.333,2.969 5.25,3.167 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to Inverter with Converter Assembly *d to ECM
*e No. 4 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F113-2 (CANH) L Hybrid vehicle control ECU
(for Bus 2)
F113-13 (CANL) P
F113-3 (CANH) G Inverter with converter assembly
(for Bus 2)
F113-14 (CANL) P
F113-4 (CANH) GR ECM
(for Bus 2)
F113-15 (CANL) P
F113-6 (CANH) R No. 4 CAN junction connector
(for Bus 2)
F113-17 (CANL) P




NO. 2 CAN JUNCTION CONNECTOR (for RHD with LITHIUM-ION BATTERY)


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C366168C94
3.333,1.083 3.833,1.333 0.5,0.25 2.667,1.583 3.042,1.844 true 2.667,1.333 3.167,1.844 true 3.292,1.823 2.667,1.083 true 3.052,2.073 2.75,2.333 true 3.188,2.073 2.833,2.583 true 3.313,2.073 3,2.833 true 3.604,2.073 4.26,3.021 true 3.583,1.854 4.458,1.104 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.094,1.479 3.01,1.677 0.917,0.198 10 false CANH*b 2.104,1.219 3.021,1.417 0.917,0.198 10 false CANH*c 2.094,0.969 3.01,1.167 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.198,2.229 3.115,2.427 0.917,0.198 10 false CANL*b 2.302,2.49 3.219,2.688 0.917,0.198 10 false CANL*c 2.458,2.75 3.375,2.948 0.917,0.198 10 false CANL*d 4.531,1 5.448,1.198 0.917,0.198 10 false CANH*e 4.333,2.948 5.25,3.146 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to Inverter with Converter Assembly *d to ECM
*e No. 6 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F113-2 (CANH) L Hybrid vehicle control ECU
(for Bus 2)
F113-13 (CANL) P
F113-3 (CANH) G Inverter with converter assembly
(for Bus 2)
F113-14 (CANL) P
F113-4 (CANH) GR ECM
(for Bus 2)
F113-15 (CANL) P
F113-6 (CANH) R No. 6 CAN junction connector
(for Bus 2)
F113-17 (CANL) P




NO. 3 CAN JUNCTION CONNECTOR


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C366168C95
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 2.417,0.417 3.323,1.833 true 4.667,0.417 3.49,1.844 true 3.604,1.844 4.719,0.729 true 3.208,2.063 2.333,3.167 true 3.49,2.063 4.25,3.583 true 2.417,1.667 2.917,1.844 true 2.333,1.25 3.083,1.844 true 2.333,2.75 3.083,2.063 true 2.333,0.833 3.208,1.833 true 3.333,2.073 2.417,3.583 true 3.615,2.052 4.563,3.198 true 4.229,1.844 4.667,1.76 true 3.969,1.844 4.646,1.24 true 4.104,1.844 4.667,1.5 true 4.229,2.052 4.667,2.25 true 4.115,2.052 4.667,2.531 true 3.958,2.063 4.698,2.781 true 3.823,2.063 4.677,3.021 true 3.813,1.833 4.719,0.979 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 1.844,0.229 2.427,0.427 0.583,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F114 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.771,3.135 2.333,3.323 0.563,0.188 10 false CANL*d 1.875,3.51 2.427,3.708 0.552,0.198 10 false CANL*e 4.75,0.323 5.333,0.51 0.583,0.188 10 false CANH*f 4.771,0.615 5.354,0.802 0.583,0.188 10 false CANH*g 4.656,3.208 5.208,3.406 0.552,0.198 10 false CANL*g 4.313,3.573 4.865,3.771 0.552,0.198 10 false CANL*f 4.75,1.125 5.333,1.313 0.583,0.188 10 false CANH*i 4.75,1.406 5.333,1.594 0.583,0.188 10 false CANH*g 4.76,1.667 5.344,1.854 0.583,0.188 10 false CANH*g 4.76,2.177 5.313,2.375 0.552,0.198 10 false CANL*g 4.729,2.458 5.281,2.656 0.552,0.198 10 false CANL*g 4.771,2.708 5.323,2.906 0.552,0.198 10 false CANL*i 4.74,2.948 5.292,3.146 0.552,0.198 10 false CANL*h 4.771,0.885 5.354,1.073 0.583,0.188 10 false CANH*h
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Combination Meter Assembly
*c to Main Body ECU (Multiplex Network Body ECU) *d to Headlight ECU Sub-assembly LH
(w/ Headlight ECU)
*e to Air Conditioning Amplifier Assembly *f to Certification ECU (Smart Key ECU Assembly)
*g to Central Gateway ECU (Network Gateway ECU) *h to DCM
*i to Radio and Display Receiver Assembly
(for Radio and Display Type)
- -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F114-1 (CANH) V Combination meter assembly
(for Bus 5)
F114-12 (CANL) SB
F114-2 (CANH) G Main body ECU (multiplex network body ECU)
(for Bus 5)
F114-13 (CANL) SB
F114-3 (CANH) L Headlight ECU sub-assembly LH*1
(for Bus 5)
F114-14 (CANL) SB
F114-4 (CANH) P Air conditioning amplifier assembly
(for Bus 5)
F114-15 (CANL) SB
F114-5 (CANH) R Certification ECU (smart key ECU assembly)
(for Bus 5)
F114-16 (CANL) SB
F114-6 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
F114-17 (CANL) SB
F114-8 (CANH) GR DCM*3
F114-19 (CANL) LG
F114-9 (CANH) B to Radio and display receiver assembly*2
(for Bus 3)
F114-20 (CANL) LG
F114-10 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 3)
F114-21 (CANL) LG
F114-11 (CANH) V Central gateway ECU (network gateway ECU)
(for Bus 3)
F114-22 (CANL) LG

*1: for LED Headlight

*2: for Radio and Display Type

*3: for LHD





NO. 4 CAN JUNCTION CONNECTOR (for RHD with LITHIUM-ION BATTERY)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C426452C01
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 4.625,0.656 3.49,1.844 true 3.604,1.844 4.656,0.927 true 3.208,2.063 2.333,3.167 true 3.479,2.052 4.667,3.479 true 2.417,1.667 2.917,1.844 true 2.333,1.25 3.083,1.844 true 2.333,2.75 3.083,2.063 true 2.333,0.833 3.208,1.833 true 3.615,2.052 4.656,3.094 true 3.729,1.833 4.646,1.208 true 3.854,1.844 4.635,1.479 true 3.979,1.844 4.635,1.729 true 3.729,2.052 4.667,2.802 true 3.854,2.063 4.635,2.469 true 3.969,2.063 4.646,2.208 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F115 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.771,3.135 2.333,3.323 0.563,0.188 10 false CANL*d 4.719,0.521 5.302,0.708 0.583,0.188 10 false CANH*e 4.74,0.813 5.323,1 0.583,0.188 10 false CANH*f 4.74,3.073 5.292,3.271 0.552,0.198 10 false CANL*f 4.75,3.469 5.302,3.667 0.552,0.198 10 false CANL*e 4.74,1.094 5.323,1.281 0.583,0.188 10 false CANH*g 4.719,1.375 5.302,1.563 0.583,0.188 10 false CANH*h 4.719,1.646 5.302,1.833 0.583,0.188 10 false CANH*c 4.719,2.135 5.271,2.333 0.552,0.198 10 false CANL*c 4.719,2.438 5.271,2.635 0.552,0.198 10 false CANL*h 4.74,2.76 5.292,2.958 0.552,0.198 10 false CANL*g
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Brake Booster with Master Cylinder Assembly *d to Power Steering ECU Assembly
*e to Steering Sensor *f to No. 5 CAN Junction Connector
*g to No. 2 CAN junction connector *h Central gateway ECU (network gateway ECU)



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F115-1 (CANH) B Airbag sensor assembly
(for Bus 4)
F115-12 (CANL) W
F115-2 (CANH) G Brake booster with master cylinder assembly
(for Bus 4)
F115-13 (CANL) W
F115-3 (CANH) P Power steering ECU assembly
(for Bus 4)
F115-14 (CANL) W
F115-5 (CANH) BE Steering sensor
(for Bus 4)
F115-16 (CANL) W
F115-6 (CANH) GR No. 5 CAN junction connector
(for Bus 4)
F115-17 (CANL) W
F115-7 (CANH) R No. 2 CAN junction connector
(for Bus 2)
F115-18 (CANL) P
F115-8 (CANH) W Central gateway ECU (network gateway ECU)
(for Bus 2)
F115-19 (CANL) P
F115-9 (CANH) LG Brake booster with master cylinder assembly
(for Bus 2)
F115-20 (CANL) P




NO. 4 CAN JUNCTION CONNECTOR (for RHD without LITHIUM-ION BATTERY)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C366168C96
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 4.625,0.656 3.49,1.844 true 3.604,1.844 4.656,0.927 true 3.208,2.063 2.333,3.167 true 3.479,2.052 4.667,3.479 true 2.417,1.667 2.917,1.844 true 2.333,1.25 3.083,1.844 true 2.333,2.75 3.083,2.063 true 2.333,0.833 3.208,1.833 true 3.615,2.052 4.656,3.094 true 3.729,1.833 4.646,1.208 true 3.854,1.844 4.635,1.479 true 3.979,1.844 4.635,1.729 true 3.729,2.052 4.667,2.802 true 3.854,2.063 4.635,2.469 true 3.969,2.063 4.646,2.208 true 3.313,2.073 2.542,3.438 true 2.448,0.521 3.333,1.823 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F115 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.771,3.135 2.333,3.323 0.563,0.188 10 false CANL*d 4.719,0.521 5.302,0.708 0.583,0.188 10 false CANH*f 4.74,0.813 5.323,1 0.583,0.188 10 false CANH*g 4.74,3.073 5.292,3.271 0.552,0.198 10 false CANL*g 4.75,3.469 5.302,3.667 0.552,0.198 10 false CANL*f 4.74,1.094 5.323,1.281 0.583,0.188 10 false CANH*h 4.719,1.375 5.302,1.563 0.583,0.188 10 false CANH*i 4.719,1.646 5.302,1.833 0.583,0.188 10 false CANH*c 4.719,2.135 5.271,2.333 0.552,0.198 10 false CANL*c 4.729,2.438 5.281,2.635 0.552,0.198 10 false CANL*i 4.74,2.76 5.292,2.958 0.552,0.198 10 false CANL*h 1.896,0.385 2.479,0.573 0.583,0.188 10 false CANH*e 2.021,3.406 2.583,3.594 0.563,0.188 10 false CANL*e
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Brake Booster with Master Cylinder Assembly *d to Power Steering ECU Assembly
*e to Brake Actuator Assembly *f to Steering Sensor
*g to No. 5 CAN Junction Connector *h to No. 2 CAN junction connector
*i Central gateway ECU (network gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F115-1 (CANH) B Airbag sensor assembly
(for Bus 4)
F115-12 (CANL) W
F115-2 (CANH) G Brake booster with master cylinder assembly
(for Bus 4)
F115-13 (CANL) W
F115-3 (CANH) P Power steering ECU assembly
(for Bus 4)
F115-14 (CANL) W
F115-4 (CANH) V Brake Actuator Assembly
F115-15 (CANL) W
F115-5 (CANH) BE Steering sensor
(for Bus 4)
F115-16 (CANL) W
F115-6 (CANH) GR No. 5 CAN junction connector
(for Bus 4)
F115-17 (CANL) W
F115-7 (CANH) R No. 2 CAN junction connector
(for Bus 2)
F115-18 (CANL) P
F115-8 (CANH) W Central gateway ECU (network gateway ECU)
(for Bus 2)
F115-19 (CANL) P
F115-9 (CANH) LG Brake booster with master cylinder assembly
(for Bus 2)
F115-20 (CANL) P




NO. 4 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C328881C17
3.313,0.385 3.813,0.635 0.5,0.25 2.135,2.094 2.74,1.646 true 2.438,2.156 3.073,1.646 true 2.823,2.354 3.406,1.646 true 1.781,0.844 2.75,1.396 true 2.125,0.594 3.073,1.417 true 2.594,0.323 3.417,1.417 true 4.094,1.396 5.073,0.458 true 3.76,1.417 4.583,0.25 true 4.083,1.646 4.917,2.333 true 3.75,1.646 4.333,2.417 true 0.74,0.854 2.375,1.396 true 0.854,1.271 2.052,1.406 true 1.333,2.094 2.396,1.604 true 1.042,1.802 2.052,1.615 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 1.583,2.031 2.167,2.26 0.583,0.229 10 false CANL*d 1.563,0.458 2.281,0.719 0.719,0.26 10 false CANH*e 2.073,0.198 2.76,0.49 0.688,0.292 10 false CANH*f 4.625,0.146 5.292,0.448 0.667,0.302 10 false CANH*g 5.135,0.344 5.719,0.656 0.583,0.313 10 false CANH*h 2.542,2.406 3.229,2.698 0.688,0.292 10 false CANL*f 2.115,2.219 2.667,2.469 0.552,0.25 10 false CANL*e 1.219,0.76 1.948,0.99 0.729,0.229 10 false CANH*d 4.188,2.438 4.833,2.677 0.646,0.24 10 false CANL*g 4.813,2.365 5.396,2.615 0.583,0.25 10 false CANL*h 3.406,0.417 4.094,0.708 0.688,0.292 10 false F116 0.177,0.74 0.948,0.938 0.771,0.198 10 false CANH*c 0.292,1.125 1.063,1.323 0.771,0.198 10 false CANH*b 0.479,1.688 1.25,1.885 0.771,0.198 10 false CANL*b 0.76,2.031 1.531,2.229 0.771,0.198 10 false CANL*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Brake Actuator Assembly *d to Brake Booster with Master Cylinder Assembly
*e to ECM *f to Steering Sensor
*g to Power Steering ECU Assembly *h to No. 5 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F116-1 (CANH) B Airbag sensor assembly
(for Bus 4)
F116-11 (CANL) W
F116-2 (CANH) V Brake actuator assembly
(for Bus 4)
F116-12 (CANL) W
F116-3 (CANH) G Brake booster with master cylinder assembly
(for Bus 4)
F116-13 (CANL) W
F116-4 (CANH) L ECM
(for Bus 4)
F116-14 (CANL) W
F116-5 (CANH) BE Steering sensor
(for Bus 4)
F116-15 (CANL) W
F116-6 (CANH) P Power steering ECU assembly
(for Bus 4)
F116-16 (CANL) W
F116-7 (CANH) GR No. 5 CAN junction connector
(for Bus 4)
F116-17 (CANL) W




NO. 5 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C328881C36
3.313,0.385 3.813,0.635 0.5,0.25 2.135,2.094 2.74,1.646 true 2.438,2.156 3.073,1.646 true 1.781,0.844 2.75,1.396 true 2.125,0.594 3.073,1.417 true 5.083,1.406 5.583,0.708 true 5.052,1.646 5.51,2.219 true 0.74,0.854 2.375,1.396 true 0.854,1.271 2.052,1.406 true 1.333,2.094 2.396,1.604 true 1.042,1.802 2.052,1.615 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 1.583,2.031 2.167,2.26 0.583,0.229 10 false CANL*d 1.563,0.458 2.281,0.719 0.719,0.26 10 false CANH*e 5.625,0.625 6.292,0.927 0.667,0.302 10 false CANH*f 2.115,2.219 2.667,2.469 0.552,0.25 10 false CANL*e 1.219,0.76 1.948,0.99 0.729,0.229 10 false CANH*d 5.563,2.146 6.208,2.385 0.646,0.24 10 false CANL*f 3.417,0.417 4.104,0.708 0.688,0.292 10 false F118 0.177,0.74 0.948,0.938 0.771,0.198 10 false CANH*c 0.292,1.125 1.063,1.323 0.771,0.198 10 false CANH*b 0.479,1.688 1.25,1.885 0.771,0.198 10 false CANL*b 0.76,2.031 1.531,2.229 0.771,0.198 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to ECM
*e to Hybrid Vehicle Control ECU *f to Brake Actuator Assembly*1


*1: for TMMT Made



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F118-1 (CANH) GR No. 4 CAN junction connector
(for Bus 4)
F118-11 (CANL) W
F118-2 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 4)
F118-12 (CANL) W
F118-3 (CANH) L ECM
(for Bus 4)
F118-13 (CANL) W
F118-4 (CANH) R Hybrid vehicle control ECU
(for Bus 4)
F118-14 (CANL) W
F118-10 (CANH) V Brake actuator assembly*1
(for Bus 4)
F118-20 (CANL) W

*1: for TMMT Made





NO. 5 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C366168C10
3.333,1.083 3.833,1.333 0.5,0.25 4.094,1.854 4.5,1.667 true 3.979,1.833 4.583,1.333 true 3.844,1.833 4.667,1 true 3.729,1.844 4.583,0.667 true 4.094,2.063 4.5,2.25 true 3.948,2.063 4.5,2.583 true 3.844,2.073 4.583,3 true 3.719,2.073 4.5,3.25 true 2.917,1.844 2.417,1.667 true 3.177,1.823 2.333,0.833 true 3.042,1.854 2.333,1.25 true 3.063,2.063 2.333,2.75 true 2.917,2.063 2.417,2.333 true 3.188,2.073 2.333,3.167 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F124 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.771,3.135 2.333,3.323 0.563,0.188 10 false CANL*d 4.656,0.542 5.24,0.729 0.583,0.188 10 false CANH*e 4.75,0.906 5.333,1.094 0.583,0.188 10 false CANH*c 4.667,1.271 5.25,1.458 0.583,0.188 10 false CANH*f 4.583,1.573 5.167,1.76 0.583,0.188 10 false CANH*g 4.594,2.156 5.156,2.344 0.563,0.188 10 false CANL*g 4.583,2.5 5.146,2.688 0.563,0.188 10 false CANL*f 4.667,2.958 5.229,3.146 0.563,0.188 10 false CANL*c 4.573,3.25 5.135,3.438 0.563,0.188 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Hybrid Vehicle Control ECU
*e to No. 6 CAN Junction Connector *f to Hybrid Vehicle Control ECU
*g to Inverter with Converter Assembly - -



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F124-1 (CANH) GR No. 4 CAN junction connector
(for Bus 4)
F124-12 (CANL) W
F124-2 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 4)
F124-13 (CANL) W
F124-3 (CANH) R Hybrid vehicle control ECU
(for Bus 4)
F124-14 (CANL) W
F124-7 (CANH) R No. 6 CAN junction connector
(for Bus 2)
F124-18 (CANL) P
F124-8 (CANH) W Central gateway ECU (network gateway ECU)
(for Bus 2)
F124-19 (CANL) P
F124-9 (CANH) L Hybrid vehicle control ECU
(for Bus 2)
F124-20 (CANL) P
F124-10 (CANH) G Inverter with converter assembly
(for Bus 2)
F124-21 (CANL) P




NO. 6 CAN JUNCTION CONNECTOR (for LHD with Blind Spot Monitor System)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C366168C97
3.333,1.083 3.833,1.333 0.5,0.25 4.667,1.125 3.969,1.854 true 4.073,1.865 4.667,1.417 true 4.229,1.844 4.573,1.74 true 3.927,2.094 4.5,2.802 true 4.615,2.51 4.083,2.063 true 4.229,2.073 4.583,2.188 true 2.313,1.229 3.24,1.844 true 2.271,1.531 3.063,1.844 true 2.302,1.813 2.927,1.875 true 2.323,2.271 2.917,2.063 true 2.313,2.615 3.052,2.063 true 2.313,2.927 3.208,2.104 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 4.74,1.302 5.656,1.5 0.917,0.198 10 false CANH*f 4.76,0.969 5.677,1.167 0.917,0.198 10 false CANH*e 4.656,1.656 5.573,1.854 0.917,0.198 10 false CANH*g 3.417,1.125 4.031,1.323 0.615,0.198 10 false M104 4.688,2.427 5.604,2.625 0.917,0.198 10 false CANL*f 4.594,2.719 5.51,2.917 0.917,0.198 10 false CANL*e 4.677,2.125 5.594,2.323 0.917,0.198 10 false CANL*g 1.74,1.146 2.656,1.344 0.917,0.198 10 false CANH*d 1.729,1.417 2.646,1.615 0.917,0.198 10 false CANH*c 1.75,1.719 2.667,1.917 0.917,0.198 10 false CANH*b 1.76,2.167 2.677,2.365 0.917,0.198 10 false CANL*b 1.781,2.521 2.698,2.719 0.917,0.198 10 false CANL*c 1.74,2.865 2.656,3.063 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Blind Spot Monitor Sensor LH *d to No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M104-9 (CANH) G Blind spot monitor sensor LH
(for Bus 1)
M104-20 (CANL) GR
M104-10 (CANH) R Central gateway ECU (network gateway ECU)
(for Bus 1)
M104-21 (CANL) GR
M104-11 (CANH) B No. 1 CAN junction connector
(for Bus 1)
M104-22 (CANL) GR




NO. 6 CAN JUNCTION CONNECTOR (for RHD with Blind Spot Monitor System)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C366168C98
3.333,1.083 3.833,1.333 0.5,0.25 4.542,1.5 4.073,1.865 true 4.542,1.167 3.917,1.844 true 4.229,1.844 4.573,1.74 true 4.083,2.042 4.469,2.479 true 3.927,2.063 4.417,2.771 true 4.229,2.073 4.583,2.188 true 4.531,0.969 3.854,1.854 true 4.24,2.927 3.823,2.052 true 2.125,1.063 3.198,1.854 true 2.115,1.365 3.052,1.844 true 2.073,1.656 2.927,1.885 true 2.104,2.302 2.917,2.073 true 2.104,2.615 3.083,2.073 true 2.115,2.938 3.208,2.073 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 4.646,1.354 5.563,1.552 0.917,0.198 10 false CANH*e 4.604,1.063 5.521,1.26 0.917,0.198 10 false CANH*f 4.656,1.656 5.573,1.854 0.917,0.198 10 false CANH*g 3.417,1.125 4.031,1.323 0.615,0.198 10 false M104 4.531,2.427 5.448,2.625 0.917,0.198 10 false CANL*e 4.49,2.698 5.406,2.896 0.917,0.198 10 false CANL*f 4.677,2.125 5.594,2.323 0.917,0.198 10 false CANL*g 4.292,2.938 5.208,3.135 0.917,0.198 10 false CANL*e 4.573,0.854 5.49,1.052 0.917,0.198 10 false CANH*e 1.552,0.979 2.469,1.177 0.917,0.198 10 false CANH*d 1.552,1.292 2.469,1.49 0.917,0.198 10 false CANH*c 1.51,1.552 2.427,1.75 0.917,0.198 10 false CANH*b 1.542,2.531 2.458,2.729 0.917,0.198 10 false CANL*c 1.542,2.208 2.458,2.406 0.917,0.198 10 false CANL*b 1.542,2.854 2.458,3.052 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Blind Spot Monitor Sensor LH *d to No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M104-8*1 (CANH)
M104-10*2 (CANH)
R Central gateway ECU (network gateway ECU)
(for Bus 1)
M104-19*1 (CANL)
M104-21*2 (CANL)
GR
M104-9 (CANH) G Blind spot monitor sensor LH
(for Bus 1)
M104-20 (CANL) GR
M104-11 (CANH) B No. 1 CAN junction connector
(for Bus 1)
M104-22 (CANL) GR

*1: for TMC Made

*2: for TMMT Made





DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C349818C78
1.625,1.313 2.042,1.583 0.417,0.271 4.469,2 4.281,1.698 true 3.458,1.125 3.198,0.76 true 4.25,0.708 3.906,1.115 true 3.823,1.698 3.646,2.063 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 4.302,0.604 4.938,0.833 0.635,0.229 10 false CANH 3.313,2.083 3.948,2.313 0.635,0.229 10 false CANL 2.958,0.646 3.594,0.875 0.635,0.229 10 false CG 4.5,2.042 5.135,2.271 0.635,0.229 10 false BAT 1.677,1.365 2.313,1.594 0.635,0.229 10 false F144
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F144-6 (CANH) - F144-14 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F144-6 (CANH) - F144-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F144-14 (CANL) - F144-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F144-6 (CANH) - F144-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F144-14 (CANL) - F144-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C349819C17
1.083,1.281 1.5,1.552 0.417,0.271 2.969,1.302 2.198,0.885 true 3.052,1.302 2.198,0.635 true 3.135,1.292 2.188,0.438 true 3.25,1.292 2.208,0.188 true 4.563,0.885 3.938,1.302 true 4.563,0.281 3.563,1.375 true 4.552,0.583 3.646,1.375 true 4.698,1.99 3.896,1.427 true 4.708,2.208 3.792,1.427 true 4.719,2.375 3.719,1.438 true 2.917,1.427 2.25,1.948 true 3.031,1.427 2.302,2.167 true 3.177,1.427 2.302,2.375 true 3.271,1.427 2.313,2.604 true 4.26,2.51 3.448,1.427 true 3.75,2.542 3.365,1.417 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.885,2.125 2.375,2.302 0.49,0.177 10 false CA1H 1.792,0.563 2.344,0.781 0.552,0.219 10 false CA1L 1.792,0.354 2.344,0.573 0.552,0.219 10 false CA2L 1.896,2.323 2.385,2.5 0.49,0.177 10 false CA2H 1.792,0.115 2.281,0.292 0.49,0.177 10 false CA3H 1.938,2.573 2.49,2.792 0.552,0.219 10 false CA3L 1.885,1.885 2.375,2.063 0.49,0.177 10 false CAXL 4.25,2.542 4.74,2.719 0.49,0.177 10 false CAYH 3.708,2.563 4.198,2.74 0.49,0.177 10 false CAYL 4.615,0.188 5.104,0.365 0.49,0.177 10 false CA4H 4.771,2.125 5.26,2.302 0.49,0.177 10 false CA5H 4.792,2.313 5.344,2.531 0.552,0.219 10 false CA5L 1.188,1.344 1.635,1.604 0.448,0.26 10 false F74 4.76,1.938 5.25,2.115 0.49,0.177 10 false CA6H 4.615,0.469 5.167,0.688 0.552,0.219 10 false CA4L 1.771,0.802 2.26,0.979 0.49,0.177 10 false CAXH 4.625,0.781 5.177,1 0.552,0.219 10 false CA6L
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C348860C05
1.417,1.333 1.917,1.583 0.5,0.25 2.344,1.26 1.896,1.104 true 2.99,1.271 1.906,0.833 true 3.083,1.552 1.823,2.073 true 3.219,1.542 1.792,2.323 true 3.344,1.542 1.781,2.552 true 5.188,1.115 4.813,1.271 true 5.198,0.896 4.656,1.26 true 5.219,0.667 4.469,1.26 true 5.198,0.448 4.271,1.26 true 5.177,0.198 4.146,1.281 true 5.208,1.719 4.75,1.542 true 5.24,1.917 4.573,1.552 true 5.219,2.125 4.188,1.552 true 5.135,2.302 4.052,1.552 true 5.115,2.51 3.917,1.542 true 4.552,2.406 3.781,1.542 true 3.656,1.552 4.052,2.354 true 3.49,1.542 2.521,2.438 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.542,1.375 2.042,1.542 0.5,0.167 10 false F74 5.26,1.031 5.76,1.198 0.5,0.167 10 false GND 5.281,1.625 5.781,1.792 0.5,0.167 10 false CAXL 5.292,1.854 5.792,2.021 0.5,0.167 10 false CA1H 5.271,2.073 5.771,2.24 0.5,0.167 10 false CA2H 5.198,2.271 5.698,2.438 0.5,0.167 10 false CA3L 5.188,2.427 5.688,2.594 0.5,0.167 10 false CAYL 4.552,2.448 5.052,2.615 0.5,0.167 10 false CAYH 4.021,2.385 4.521,2.552 0.5,0.167 10 false CA4H 2.208,2.448 2.708,2.615 0.5,0.167 10 false CA4L 1.521,1 2.021,1.167 0.5,0.167 10 false BATT 1.521,0.719 2.021,0.885 0.5,0.167 10 false CA6L 1.406,2 1.906,2.167 0.5,0.167 10 false CA6H 1.396,2.24 1.896,2.406 0.5,0.167 10 false CA5H 1.396,2.479 1.896,2.646 0.5,0.167 10 false CA5L 5.26,0.802 5.76,0.969 0.5,0.167 10 false CAXH 5.271,0.573 5.771,0.74 0.5,0.167 10 false CA1L 5.271,0.344 5.771,0.51 0.5,0.167 10 false CA2L 5.271,0.094 5.771,0.26 0.5,0.167 10 false CA3H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-14 (CA6H) - F74-5 (CA6L) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
F74-14 (CA6H) - F74-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-5 (CA6L) - F74-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-14 (CA6H) - F74-1 (BATT) R - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F74-5 (CA6L) - F74-1 (BATT) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) R - P HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) GR - GR LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-23 (CA1H) - F74-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-8 (CA1L) - F74-10 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-23 (CA1H) - F74-1 (BATT) R - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F74-8 (CA1L) - F74-1 (BATT) GR - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-18 (CA4H) - F74-17 (CA4L) W - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F74-18 (CA4H) - F74-10 (GND) W - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-17 (CA4L) - F74-10 (GND) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-18 (CA4H) - F74-1 (BATT) W - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F74-17 (CA4L) - F74-1 (BATT) P - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-6 (CA3H) - F74-19 (CAYH) G - V HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-21 (CA3L) - F74-20 (CAYL) LG - LG LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
F74-6 (CA3H) - F74-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-21 (CA3L) - F74-10 (GND) LG - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-6 (CA3H) - F74-1 (BATT) G - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F74-21 (CA3L) - F74-1 (BATT) LG - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-22 (CA2H) - F74-7 (CA2L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F74-22 (CA2H) - F74-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-7 (CA2L) - F74-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-22 (CA2H) - F74-1 (BATT) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F74-7 (CA2L) - F74-1 (BATT) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-15 (CA5H) - F74-16 (CA5L) B - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F74-15 (CA5H) - F74-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-16 (CA5L) - F74-10 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-15 (CA5H) - F74-1 (BATT) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F74-16 (CA5L) - F74-1 (BATT) SB - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEERING SENSOR


C349821C04
4.385,0.406 4.802,0.667 0.417,0.26 4.438,2.167 4.604,1.667 true 5,2.167 4.75,1.677 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.49,0.479 4.948,0.677 0.458,0.198 10 false F69 5,2.198 5.583,2.448 0.583,0.25 10 false CANL 4.083,2.198 4.667,2.448 0.583,0.25 10 false CANH
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F69 steering sensor connector.


c.
C366202C01
1.458,0.333 1.958,0.583 0.5,0.25 2.104,1.354 2.417,1.583 true 1.031,1.917 1.677,1.344 true 0.958,1.688 1.51,1.354 true 1.01,1.479 1.333,1.354 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.573,0.385 1.885,0.583 0.313,0.198 10 false F69 0.594,1.667 1.156,1.833 0.563,0.167 10 false CANL 0.656,1.427 1.219,1.594 0.563,0.167 10 false ESS 0.615,1.917 1.177,2.083 0.563,0.167 10 false CANH 2.438,1.615 3,1.781 0.563,0.167 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F69-3 (CANH) - F69-2 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F69-3 (CANH) - F69-1 (ESS) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F69-2 (CANL) - F69-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F69-3 (CANH) - F69-5 (BAT) BE - P HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F69-2 (CANL) - F69-5 (BAT) W - P LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU (for 2ZR-FXE)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F2 and F3 hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

C366201C01
1.646,0.417 2.146,0.667 0.5,0.25 4.792,0.417 5.292,0.667 0.5,0.25 2.708,1.188 3,0.917 true 4.083,0.833 4.781,1.208 true 5.708,1.594 6.083,1.417 true 5.552,1.594 6.167,1 true 5.698,1.885 6.083,2.083 true 5.552,1.885 6.052,2.385 true 0.188,0.083 0.5,0.281 0.313,0.198 10 false *a 1.813,0.479 2.125,0.677 0.313,0.198 10 false F2 4.958,0.469 5.271,0.667 0.313,0.198 10 false F3 3.083,0.833 3.396,1.031 0.313,0.198 10 false E1 3.677,0.771 4.156,0.938 0.479,0.167 10 false BATT 6.25,0.927 6.729,1.094 0.479,0.167 10 false CA1L 6.177,1.354 6.656,1.521 0.479,0.167 10 false CA1H 6.156,2.063 6.656,2.229 0.5,0.167 10 false CA3P 6.094,2.417 6.594,2.583 0.5,0.167 10 false CA3N
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F3-25 (CA1H) - F3-24 (CA1L) L - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F3-25 (CA1H) - F2-6 (E1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F3-24 (CA1L) - F2-6 (E1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F3-25 (CA1H) - F3-3 (BATT) L - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F3-24 (CA1L) - F3-3 (BATT) P - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F3-31 (CA3P) - F3-30 (CA3N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F3-31 (CA3P) - F2-6 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F3-30 (CA3N) - F2-6 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F3-31 (CA3P) - F3-3 (BATT) R - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F3-30 (CA3N) - F3-3 (BATT) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU (for M20A-FXS)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F160 and F161 hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

C350875C08
1.781,0.188 2.177,0.458 0.396,0.271 5.135,0.188 5.5,0.458 0.365,0.271 4.656,1.406 4.365,0.76 true 4.115,2.125 4.375,1.656 true 1.667,2.219 2.094,1.542 true 2.438,2.25 2.229,1.521 true 2.031,1.406 1.688,0.688 true 2.177,1.375 2.479,0.719 true 1.26,0.615 1.875,0.813 0.615,0.198 10 false CA3P 1.26,2.135 1.875,2.333 0.615,0.198 10 false CA3N 2.49,2.167 3.104,2.365 0.615,0.198 10 false CA1H 2.563,0.635 3.177,0.833 0.615,0.198 10 false CA1L 0.104,0.083 0.719,0.281 0.615,0.198 10 false *a 1.823,0.24 2.438,0.438 0.615,0.198 10 false F160 5.167,0.24 5.781,0.438 0.615,0.198 10 false F161 3.74,2.052 4.354,2.25 0.615,0.198 10 false BATT 4.135,0.667 4.75,0.865 0.615,0.198 10 false E1
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F160-21 (CA1H) - F160-8 (CA1L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F160-21 (CA1H) - F161-3 (E1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F160-8 (CA1L) - F161-3 (E1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F160-21 (CA1H) - F161-27 (BATT) L - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F160-8 (CA1L) - F161-27 (BATT) P - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F160-7 (CA3P) - F160-20 (CA3N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F160-7 (CA3P) - F161-3 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F160-20 (CA3N) - F161-3 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F160-7 (CA3P) - F161-27 (BATT) R - B*1
R - Y*2
HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F160-20 (CA3N) - F161-27 (BATT) W - B*1
W - Y*2
LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


*1: for RHD

*2: for LHD




INVERTER WITH CONVERTER ASSEMBLY (for 2ZR-FXE)


Refer to Terminals of ECU.


CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the C65 inverter with converter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

C350876C23
4.99,0.25 5.396,0.531 0.406,0.281 1.875,0.135 2.281,0.417 0.406,0.281 1.135,1.344 1.656,1.344 true 2.229,1.542 3.063,1.552 true 1.656,1.229 1.083,0.917 true 5.885,1.667 6.156,2 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.625,0.813 1.115,1.052 0.49,0.24 10 false CANH 0.677,1.281 1.167,1.521 0.49,0.24 10 false CANL 3.135,1.49 3.625,1.729 0.49,0.24 10 false GND1 6.156,2.021 6.646,2.26 0.49,0.24 10 false BAT 5.042,0.302 5.531,0.542 0.49,0.24 10 false F144 1.958,0.208 2.448,0.448 0.49,0.24 10 false C65 3.729,0.146 4.042,0.344 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C65-1 (CANH) - C65-7 (CANL) G - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
C65-1 (CANH) - C65-24 (GND1) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C65-7 (CANL) - C65-24 (GND1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C65-1 (CANH) - F144-16 (BAT) G - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
C65-7 (CANL) - F144-16 (BAT) P - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INVERTER WITH CONVERTER ASSEMBLY (for M20A-FXS)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>TERMINALS OF ECU

CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the C98 inverter with converter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

C350876C24
4.99,0.25 5.5,0.5 0.51,0.25 1.833,0.167 2.333,0.417 0.5,0.25 1.135,1.344 1.656,1.344 true 2.229,1.542 3.063,1.552 true 1.677,1.24 1.198,0.406 true 6.156,2.115 5.844,1.667 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.76,0.323 1.25,0.563 0.49,0.24 10 false CANH 0.677,1.281 1.167,1.521 0.49,0.24 10 false CANL 3.135,1.49 3.625,1.729 0.49,0.24 10 false GND1 6.24,2.042 6.729,2.281 0.49,0.24 10 false BAT 5.083,0.302 5.573,0.542 0.49,0.24 10 false F144 1.927,0.208 2.417,0.448 0.49,0.24 10 false C98 3.729,0.146 4.042,0.344 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C98-1 (CANH) - C98-7 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
C98-1 (CANH) - C98-24 (GND1) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C98-7 (CANL) - C98-24 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C98-1 (CANH) - F144-16 (BAT) G - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
C98-7 (CANL) - F144-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM (for 2ZR-FXE)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A38 and C63 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C349827C08
1.229,0.313 1.625,0.563 0.396,0.25 4.417,0.271 4.823,0.49 0.406,0.219 2.125,1.24 2.333,0.583 true 2.135,1.365 2.385,2.281 true 0.865,1.24 0.615,0.49 true 3.031,1.406 3.25,0.75 true 6.177,1.385 6.583,0.583 true 2.948,1.396 3.24,0.5 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.51,0.323 4.823,0.521 0.313,0.198 10 false C63 1.323,0.375 1.635,0.573 0.313,0.198 10 false A38 2.396,0.5 3.021,0.708 0.625,0.208 10 false CANH 2.354,2.313 2.979,2.521 0.625,0.208 10 false CANL 3.302,0.396 3.927,0.604 0.625,0.208 10 false CAN+ 3.323,0.667 3.948,0.875 0.625,0.208 10 false CAN- 0.24,0.354 0.865,0.563 0.625,0.208 10 false BATT 6.656,0.469 6.958,0.677 0.302,0.208 10 false E1
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-13 (CANH) - A38-26 (CANL) GR - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A38-13 (CANH) - C63-59 (E1) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A38-26 (CANL) - C63-59 (E1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A38-13 (CANH) - A38-1 (BATT) GR - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A38-26 (CANL) - A38-1 (BATT) P - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
C63-31 (CAN+) - C63-32 (CAN-) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
C63-31 (CAN+) - C63-59 (E1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C63-32 (CAN-) - C63-59 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
C63-31 (CAN+) - A38-1 (BATT) L - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
C63-32 (CAN-) - A38-1 (BATT) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM (for M20A-FXS)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A96 ECM connector.


c.
C392553C13
0.198,0.938 0.615,1.188 0.417,0.25 0.635,1.885 1.927,0.771 true 2.844,1.896 1.927,0.865 true 0.594,1.521 1.365,0.781 true 2.865,1.333 2.375,0.906 true 0.188,0.177 0.406,0.427 0.219,0.25 10 false *a 2.906,1.823 3.427,2.073 0.521,0.25 10 false CANL 0.292,0.979 0.719,1.188 0.427,0.208 10 false A96 0.219,1.813 0.74,2.063 0.521,0.25 10 false CANH 0.219,1.438 0.667,1.656 0.448,0.219 10 false BATT 2.938,1.26 3.313,1.49 0.375,0.229 10 false E1
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A96-8 (CANH) - A96-18 (CANL) P - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A96-8 (CANH) - A96-10 (E1) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A96-18 (CANL) - A96-10 (E1) GL - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A96-8 (CANH) - A96-1 (BATT) P - G HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A96-18 (CANL) - A96-1 (BATT) GL - G LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F4 combination meter assembly connector.


c.
C328874C20
1.417,0.25 1.917,0.5 0.5,0.25 0.656,1.75 0.417,1.354 true 2.167,1.75 1.948,1.344 true 2.917,1.75 3.021,1.333 true 1.667,1.75 1.75,1.344 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.583,0.281 1.896,0.479 0.313,0.198 10 false F4 0.688,1.75 1,1.948 0.313,0.198 10 false ET 1.375,1.781 1.875,1.948 0.5,0.167 10 false CANL 2.125,1.781 2.625,1.948 0.5,0.167 10 false CANH 2.865,1.792 3.031,1.958 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F4-32 (CANH) - F4-31 (CANL) V - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F4-32 (CANH) - F4-21 (ET) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F4-31 (CANL) - F4-21 (ET) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F4-32 (CANH) - F4-40 (B) V - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F4-31 (CANL) - F4-40 (B) SB - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A39 brake booster with master cylinder assembly connector.


c.
C349830C15
1.542,0.146 1.958,0.417 0.417,0.271 1.531,1.667 1.333,0.667 true 1.625,1.667 1.833,0.667 true 2.656,1.448 2.833,0.583 true 2.917,2.5 2.635,1.906 true 1.833,2.583 1.625,1.927 true 1.333,2.583 1.5,1.948 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.635,0.177 1.948,0.375 0.313,0.198 10 false A39 1.906,0.542 2.458,0.823 0.552,0.281 10 false CA2H 0.958,0.542 1.51,0.823 0.552,0.281 10 false CA2L 1,2.583 1.552,2.865 0.552,0.281 10 false CA1L 1.813,2.604 2.365,2.885 0.552,0.281 10 false CA1H 2.885,0.5 3.344,0.75 0.458,0.25 10 false GND1 2.906,2.542 3.208,2.813 0.302,0.271 10 false BS
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A39-30 (CA2H) - A39-29 (CA2L) LG - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A39-30 (CA2H) - A39-26 (GND1) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-29 (CA2L) - A39-26 (GND1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-30 (CA2H) - A39-52 (BS) LG - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A39-29 (CA2L) - A39-52 (BS) P - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A39-43 (CA1H) - A39-42 (CA1L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A39-43 (CA1H) - A39-26 (GND1) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-42 (CA1L) - A39-26 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-43 (CA1H) - A39-52 (BS) G - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A39-42 (CA1L) - A39-52 (BS) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C350877C14
4.948,0.146 5.333,0.406 0.385,0.26 1.75,0.115 2.135,0.375 0.385,0.26 5.094,1.104 4.917,0.75 true 2.26,1.365 2.833,0.75 true 2.146,1.365 2.75,0.417 true 6.083,1.917 5.875,1.667 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 4.677,0.594 4.99,0.792 0.313,0.198 10 false CG 6.073,1.958 6.385,2.156 0.313,0.198 10 false BAT 4.979,0.188 5.427,0.427 0.448,0.24 10 false F144 1.823,0.167 2.135,0.365 0.313,0.198 10 false F15 2.927,0.646 3.531,0.896 0.604,0.25 10 false CANH 2.813,0.302 3.417,0.552 0.604,0.25 10 false CANL 3.75,0.073 4.063,0.271 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F15-14 (CANH) - F15-13 (CANL) G - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F15-14 (CANH) - F144-4 (CG) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F15-13 (CANL) - F144-4 (CG) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F15-14 (CANH) - F144-16 (BAT) G - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F15-13 (CANL) - F144-16 (BAT) SB - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


c.
C366211C01
1.417,0.417 1.917,0.667 0.5,0.25 1.083,1.448 0.667,0.865 true 0.51,1.5 0.896,1.5 true 0.448,2.573 0.865,1.99 true 2.542,1.458 3.042,0.958 true 1.583,0.438 1.896,0.635 0.313,0.198 10 false F1 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.24,0.76 0.719,1.042 0.479,0.281 10 false CANL 0.063,1.406 0.542,1.688 0.479,0.281 10 false CANH 0.323,2.563 0.635,2.76 0.313,0.198 10 false E 3.104,0.865 3.417,1.063 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F1-1 (CANH) - F1-2 (CANL) R - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F1-1 (CANH) - F1-18 (E) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F1-2 (CANL) - F1-18 (E) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F1-1 (CANH) - F1-4 (+B) R - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F1-2 (CANL) - F1-4 (+B) SB - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F23 and F68 power steering ECU assembly connectors.


c.
C328899C08
0.417,1.25 0.917,1.5 0.5,0.25 0.417,3.167 0.917,3.417 0.5,0.25 1.167,2 1.333,1.5 true 2.333,2 2.083,1.5 true 1.5,4.083 1.75,3.448 true 2.333,4.083 2.01,3.438 true 0.542,3.198 1,3.396 0.458,0.198 10 false F23 0.531,1.292 0.99,1.49 0.458,0.198 10 false F68 0.979,2.031 1.438,2.229 0.458,0.198 10 false PIG 2.313,2.031 2.938,2.229 0.625,0.198 10 false PGND 2.313,4.125 2.938,4.323 0.625,0.198 10 false CANL 1.198,4.135 1.823,4.333 0.625,0.198 10 false CANH 0.208,0.135 0.667,0.333 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F23-7 (CANH) - F23-8 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F23-7 (CANH) - F68-2 (PGND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F23-8 (CANL) - F68-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F23-7 (CANH) - F68-1 (PIG) P - B-W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F23-8 (CANL) - F68-1 (PIG) W - B-W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F142 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350879C39
1.688,0.188 2.104,0.458 0.417,0.271 5.073,0.177 5.49,0.448 0.417,0.271 1.604,2.073 1.708,1.469 true 2.552,2.094 2.927,1.313 true 3.333,2.063 3.063,1.313 true 6.188,2.219 5.958,1.656 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.917,0.115 4.229,0.313 0.313,0.198 10 false *1 2.448,2.135 2.76,2.333 0.313,0.198 10 false R1 3.26,2.115 3.573,2.313 0.313,0.198 10 false R2 1.729,0.24 2.115,0.51 0.385,0.271 10 false F142 1.521,2.104 1.833,2.302 0.313,0.198 10 false E 6.083,2.26 6.604,2.469 0.521,0.208 10 false BAT 5.125,0.24 5.51,0.51 0.385,0.271 10 false F144
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F142-17 (R1) - F142-18 (R2) SB - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F142-17 (R1) - F142-28 (E) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F142-18 (R2) - F142-28 (E) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F142-17 (R1) - F144-16 (BAT) SB - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F142-18 (R2) - F144-16 (BAT) GR - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F150 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C392557C04
5,0.417 5.5,0.667 0.5,0.25 1.729,0.167 2.229,0.417 0.5,0.25 5.021,2.229 5.844,1.635 true 2.365,1.635 3.135,1.302 true 2.073,1.906 2.823,2.458 true 2.26,1.635 0.906,1.281 true 0.156,0.146 0.479,0.448 0.323,0.302 10 false *a 3.979,0.271 4.385,0.563 0.406,0.292 10 false *1 5.083,0.448 5.521,0.708 0.438,0.26 10 false F144 1.813,0.198 2.271,0.396 0.458,0.198 10 false F150 0.49,1.219 1.104,1.417 0.615,0.198 10 false CANH 3.219,1.219 3.833,1.417 0.615,0.198 10 false CANL 4.719,2.135 5.135,2.385 0.417,0.25 10 false BAT 2.927,2.385 3.24,2.583 0.313,0.198 10 false E1
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F150-26 (CANH) - F150-27 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
F150-26 (CANH) - F150-33 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F150-27 (CANL) - F150-33 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F150-26 (CANH) - F144-16 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F150-27 (CANL) - F144-16 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F73 air conditioning amplifier assembly connector.


c.
C349836C14
1.5,0.208 1.917,0.479 0.417,0.271 0.781,1.604 0.5,1.25 true 1.865,1.833 1.5,1 true 2.031,1.833 2.25,1 true 2.656,1.594 2.833,1.167 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.604,0.281 1.917,0.479 0.313,0.198 10 false F73 1.073,0.896 1.74,1.104 0.667,0.208 10 false CANH 2.333,0.885 3,1.094 0.667,0.208 10 false CANL 2.927,1.073 3.396,1.302 0.469,0.229 10 false GND 0.365,1.094 0.833,1.323 0.469,0.229 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F73-11 (CANH) - F73-12 (CANL) P - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F73-11 (CANH) - F73-4 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F73-12 (CANL) - F73-4 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F73-11 (CANH) - F73-1 (B) P - V HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F73-12 (CANL) - F73-1 (B) SB - V LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F131 and F129 radio and display receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C371295C79
0.5,0.833 1,1.083 0.5,0.25 3.833,0.833 4.333,1.083 0.5,0.25 1.125,1.469 1.469,0.844 true 2.948,0.823 3.292,1.51 true 5.458,0.979 5.198,1.458 true 5.573,0.969 5.781,1.469 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 0.594,0.885 1.052,1.063 0.458,0.177 10 false F129 3.927,0.885 4.396,1.104 0.469,0.219 10 false F131 3.156,1.521 3.469,1.719 0.313,0.198 10 false +B1 0.896,1.51 1.365,1.698 0.469,0.188 10 false GND1 5.01,1.49 5.479,1.677 0.469,0.188 10 false CANH 5.625,1.49 6.094,1.677 0.469,0.188 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F131-13 (CANH) - F131-14 (CANL) B - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F131-13 (CANH) - F129-1 (GND1) B - LA HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F131-14 (CANL) - F129-1 (GND1) LG - LA LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F131-13 (CANH) - F129-4 (+B1) B - LA-SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F131-14 (CANL) - F129-4 (+B1) LG - LA-SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY LH (for LED Headlight)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A95*1 or A100*2 headlight ECU sub-assembly LH connector.

*1: for TMMT Made

*2: for TMC Made



c.

Measure the resistance according to the value(s) in the table below.

C366205C69
1,0.417 1.5,0.667 0.5,0.25 5.25,0.583 5.75,0.833 0.5,0.25 1.917,0.417 2.417,0.667 0.5,0.25 0.594,2.146 0.844,1.635 true 2.406,2.188 2.635,1.677 true 3.125,2.146 2.813,1.688 true 6.354,1.969 6.167,1.74 true 0.104,0.052 0.417,0.25 0.313,0.198 10 false *a 1.115,0.469 1.51,0.635 0.396,0.167 10 false A95 5.333,0.615 5.792,0.813 0.458,0.198 10 false F144 0.365,2.177 0.76,2.344 0.396,0.167 10 false GND 2.135,2.208 2.698,2.375 0.563,0.167 10 false CANL 3.104,2.188 3.667,2.354 0.563,0.167 10 false CANH 6.375,2.021 6.938,2.188 0.563,0.167 10 false BAT 4,0.063 4.313,0.26 0.313,0.198 10 false *1 1.563,0.469 1.896,0.75 0.333,0.281 12 false *A 2.49,0.479 2.823,0.76 0.333,0.281 12 false *B 2.021,0.49 2.438,0.656 0.417,0.167 10 false A100
*A for TMMT Made *B for TMC Made
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)
- -


Standard Resistance:
for TMMT Made:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A95-24 (CANH) - A95-23 (CANL) L - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A95-24 (CANH) - A95-12 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A95-23 (CANL) - A95-12 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A95-24 (CANH) - F144-16 (BAT) L - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A95-23 (CANL) - F144-16 (BAT) SB- R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for TMC Made:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A100-24 (CANH) - A100-23 (CANL) L - SB HIGH-level CAN bus line - LOWlevel CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A100-24 (CANH) - A100-12 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A100-23 (CANL) - A100-12 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A100-24 (CANH) - F144-16 (BAT) L - R HIGH-level CAN bus line - Auxiliary battery positive(+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A100-23 (CANL) - F144-16 (BAT) SB- R LOW-level CAN bus line - Auxiliary battery positive(+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M62 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C350884C49
1.688,0.135 2.115,0.427 0.427,0.292 4.979,0.208 5.406,0.5 0.427,0.292 6.094,2.021 5.854,1.667 true 1.719,1.313 1.51,0.688 true 1.458,2.135 1.708,1.563 true 2.51,2.146 2.25,1.563 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.635,0.073 3.948,0.271 0.313,0.198 10 false *1 1.771,0.219 2.094,0.417 0.323,0.198 10 false M62 5.042,0.26 5.458,0.51 0.417,0.25 10 false F144 1.125,2.167 1.615,2.417 0.49,0.25 10 false CA1N 1.125,0.552 1.615,0.802 0.49,0.25 10 false CA1P 2.49,2.208 2.979,2.458 0.49,0.25 10 false BLGD 6.073,2.063 6.563,2.313 0.49,0.25 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M62-2 (CA1P) - M62-7 (CA1N) G - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
M62-2 (CA1P) - M62-10 (BLGD) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M62-7 (CA1N) - M62-10 (BLGD) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M62-2 (CA1P) - F144-16 (BAT) G - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M62-7 (CA1N) - F144-16 (BAT) GR - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C350886C53
1.823,0.146 2.146,0.396 0.323,0.25 4.979,0.198 5.385,0.469 0.406,0.271 2.25,1.333 2.781,0.948 true 1.927,2.063 2.042,1.688 true 2.417,2.031 2.24,1.698 true 6.094,1.948 5.875,1.677 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *1 1.896,0.198 2.208,0.396 0.313,0.198 10 false R5 2.844,0.844 3.313,1.063 0.469,0.219 10 false CA1P 2.396,2.073 2.865,2.292 0.469,0.219 10 false CA1N 1.677,2.083 2.146,2.302 0.469,0.219 10 false GND 5.031,0.25 5.469,0.521 0.438,0.271 10 false F144 6.083,2 6.552,2.219 0.469,0.219 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-5 (CA1P) - R5-11 (CA1N) R - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
R5-5 (CA1P) - R5-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-11 (CA1N) - R5-10 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-5 (CA1P) - F144-16 (BAT) R - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R5-11 (CA1N) - F144-16 (BAT) GR - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A2 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350887C55
4.99,0.208 5.354,0.479 0.365,0.271 1.74,0.115 2.104,0.385 0.365,0.271 0.99,1.344 1.688,1.344 true 6.063,1.958 5.875,1.667 true 2.458,0.656 2.125,1.26 true 1.646,0.646 1.854,1.26 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *1 1.25,0.542 1.729,0.75 0.479,0.208 10 false CA2L 2.51,0.552 2.99,0.76 0.479,0.208 10 false CA2H 0.531,1.281 1.01,1.49 0.479,0.208 10 false SGND 6.073,1.99 6.552,2.198 0.479,0.208 10 false BAT 5.01,0.271 5.521,0.5 0.51,0.229 10 false F144 1.844,0.177 2.167,0.375 0.323,0.198 10 false A2
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-3 (CA2H) - A2-2 (CA2L) G - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A2-3 (CA2H) - A2-1 (SGND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-2 (CA2L) - A2-1 (SGND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A2-3 (CA2H) - F144-16 (BAT) G - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A2-2 (CA2L) - F144-16 (BAT) GR - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY


Refer to Terminals of ECU.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M71 and M70 brake actuator assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C393503C03
1.833,0.333 2.25,0.583 0.417,0.25 5.083,0.333 5.5,0.583 0.417,0.25 0.396,2.25 1.396,1.406 true 3.344,2.24 2.698,1.448 true 2.469,2.219 1.854,1.51 true 1.25,2.24 1.729,1.542 true 4.094,2.208 4.688,1.427 true 4.635,2.24 4.958,1.552 true 5.417,2.219 5.104,1.521 true 6.323,2.229 5.958,1.427 true 0.156,0.115 0.375,0.354 0.219,0.24 10 false *a 2.354,0.375 2.615,0.563 0.26,0.188 10 false *B 1.917,0.375 2.229,0.573 0.313,0.198 10 false A84 5.177,0.375 5.49,0.573 0.313,0.198 10 false A85 5.604,0.375 5.865,0.563 0.26,0.188 10 false *A 0.198,2.281 0.813,2.479 0.615,0.198 10 false EGND 1.073,2.281 1.688,2.479 0.615,0.198 10 false CANL 2.302,2.281 2.917,2.479 0.615,0.198 10 false CANH 3.208,2.281 3.823,2.479 0.615,0.198 10 false BEPB 3.906,2.281 4.521,2.479 0.615,0.198 10 false EGND 4.479,2.281 5.094,2.479 0.615,0.198 10 false CANL 5.229,2.281 5.844,2.479 0.615,0.198 10 false CANH 6.125,2.281 6.74,2.479 0.615,0.198 10 false BEPB
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))
- -


Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A85-12 (CANH) - A85-11 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A85-12 (CANH) - A85-2 (EGND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A85-11 (CANL) - A85-2 (EGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A85-12 (CANH) - A85-9 (BEPB) V - G HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A85-11 (CANL) - A85-9 (BEPB) W - G LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Standard Resistance:
for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A84-12 (CANH) - A84-11 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A84-12 (CANH) - A84-2 (EGND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A84-11 (CANL) - A84-2 (EGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A84-12 (CANH) - A84-9 (BEPB) V - G HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A84-11 (CANL) - A84-9 (BEPB) W - G LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C285245C45
1.5,0.083 1.917,0.333 0.417,0.25 2.417,1.917 2.01,1.219 true 1.417,1.917 1.844,1.219 true 2.427,0.917 2.917,0.25 true 0.49,0.906 0.75,0.25 true 0.052,0.042 0.385,0.302 0.333,0.26 10 false *a 2.26,1.969 2.875,2.167 0.615,0.198 10 false CANN 1.219,1.969 1.833,2.167 0.615,0.198 10 false CANP 1.51,0.135 1.979,0.385 0.469,0.25 10 false F165 0.792,0.083 1.177,0.406 0.385,0.323 10 false +B 2.969,0.094 3.24,0.385 0.271,0.292 10 false E
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the F165 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F165-15 (CANP) - F165-16 (CANN) GR - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F165-15 (CANP) - F165-4 (E) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F165-16 (CANN) - F165-4 (E) LG - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F165-15 (CANP) - F165-1 (+B) GR - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F165-16 (CANN) - F165-1 (+B) LG - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BATTERY ECU ASSEMBLY (for LITHIUM-ION BATTERY)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the z15 battery ECU assembly connector.


c.
C349826C06
1.531,0.385 1.948,0.656 0.417,0.271 1.052,1.813 0.719,0.875 true 2.438,1.813 2.74,0.865 true 1.646,2.865 1.24,2.156 true 0.635,2.875 0.979,2.135 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.479,2.917 0.979,3.125 0.5,0.208 10 false CA2H 0.323,0.75 0.823,0.958 0.5,0.208 10 false CA2L 1.635,0.458 2.135,0.667 0.5,0.208 10 false z22 1.521,2.896 2.021,3.104 0.5,0.208 10 false GND1 2.771,0.729 3.094,0.958 0.323,0.229 10 false AM
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
z22-9 (CA2H) - z22-1 (CA2L) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
z22-9 (CA2H) - z22-10 (GND1) R - GR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
z22-1 (CA2L) - z22-10 (GND1) W - GR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
z22-9 (CA2H) - z22-8 (AM) R - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
z22-1 (CA2L) - z22-8 (AM) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the N63 parking assist ECU connector.


c.
C403821C14
1.458,0.844 1.958,1.094 0.5,0.25 3,1.729 2.26,2.667 true 3.01,1.917 2.917,2.677 true 0.365,1.729 0.177,2.635 true 0.552,1.74 0.667,2.688 true 1.552,0.885 2.167,1.083 0.615,0.198 10 false M116 2.042,2.698 2.656,2.896 0.615,0.198 10 false CANL 2.74,2.719 3.354,2.917 0.615,0.198 10 false CANH 0.094,0.094 0.708,0.292 0.615,0.198 10 false *a 0.104,2.677 0.719,2.875 0.615,0.198 10 false +B 0.5,2.74 1.115,2.938 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M116-40 (CANH) - M116-18 (CANL) L - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
M116-40 (CANH) - M116-2 (GND1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M116-18 (CANL) - M116-2 (GND1) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M116-40 (CANH) - M116-1 (+B) L - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M116-18 (CANL) - M116-1 (+B) GR - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




VEHICLE APPROACHING SPEAKER CONTROLLER


Refer to Terminals of ECU.

Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>ACOUSTIC VEHICLE ALERTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F172 vehicle approaching speaker controller connector.


c.

Measure the resistance according to the value(s) in the table below.

C398277C49
4.99,0.281 5.438,0.51 0.448,0.229 1.865,0.344 2.313,0.573 0.448,0.229 1.677,2 1.833,1.573 true 1.833,2.24 2,1.563 true 2.458,2.01 2.271,1.573 true 6,2.094 5.813,1.656 true 3.552,0.292 3.865,0.49 0.313,0.198 10 false *1 0.958,0.313 1.271,0.51 0.313,0.198 10 false *a 1.927,0.375 2.375,0.625 0.448,0.25 10 false F172 5.063,0.323 5.5,0.573 0.438,0.25 10 false F144 2.5,1.927 3.115,2.167 0.615,0.24 10 false GND 1.25,1.906 1.781,2.146 0.531,0.24 10 false CANH 1.427,2.167 1.958,2.406 0.531,0.24 10 false CANL 6.052,2 6.583,2.24 0.531,0.24 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F172-3 (CANH) - F172-4 (CANL) LG - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F172-3 (CANH) - F172-6 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F172-4 (CANL) - F172-6 (GND) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F172-3 (CANH) - F144-16 (BAT) LG - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F172-4 (CANL) - F144-16(BAT) P - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher