The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL.
The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch contains momentary type contacts for each function. The contacts close only while the cruise control main switch is being operated in the direction of the relative function arrow, and open when the cruise control main switch is released. The voltage at the terminal of the hybrid vehicle control ECU assembly changes as each of the different contacts open or close. The hybrid vehicle control ECU assembly reads this voltage and controls the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions accordingly.
Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button).
The operation of constant speed control mode is the same as that for a conventional cruise control system.
for 2ZR-FXE
for M20A-FXS
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Cruise Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| -SET Switch | -SET switch signal | ON or OFF | ON: -SET switch on
OFF: -SET switch off |
- |
| +RES Switch | +RES switch signal | ON or OFF | ON: +RES switch on
OFF: +RES switch off |
- |
| Cruise Main Switch Operation Condition | Cruise control main switch (ON-OFF button) status | ON or OFF | ON: Cruise control main switch (ON-OFF button) pushed
OFF: Cruise control main switch (ON-OFF button) not pushed |
- |
| Tester Display |
|---|
| -SET Switch |
| +RES Switch |
| Cruise Main Switch Operation Condition |
The Data List items shown in the table change according to the operation of the cruise control main switch.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the cruise control main switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL
Inspect the cruise control main switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
| *b | Front view of wire harness connector
(to Cruise Control Main Switch) |
Remove the cruise control switch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| Cruise control main switch side connector terminal 3 - z4-3 | Below 1 Ω |
| Cruise control main switch side connector terminal 1 - z4-4 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F29 spiral cable sub-assembly connector.
Disconnect the F2 hybrid vehicle control ECU connector. (for 2ZR-FXE)
Disconnect the F161 hybrid vehicle control ECU connector. (for M20A-FXS)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F29-1 (CCS) - F2-28 (CCS) | Always | Below 1 Ω |
| F29-2 (ECC) - Body ground | Always | Below 1 Ω |
| F29-1 (CCS) or F2-28 (CCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F29-1 (CCS) - F161-14 (CCS) | Always | Below 1 Ω |
| F29-2 (ECC) - Body ground | Always | Below 1 Ω |
| F29-1 (CCS) or F161-14 (CCS) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for 2ZR-FXE) | A |
| OK (for M20A-FXS) | B |
| NG | C |
A
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
B
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
C