Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
69760C
1.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
w/o Double Locking System:
Engage the guide to install the front door inside locking cable assembly to the front door lock with motor assembly.
w/ Double Locking System:
Engage the guide to install the front door inside locking cable assembly to the front door lock with motor assembly.
|
Install in this Direction |
Engage the claws as shown in the illustration.
69720B
2.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
w/o Double Locking System:
Engage the guide to install the front door lock remote control cable assembly to the front door lock with motor assembly.
w/ Double Locking System:
Engage the guide to install the front door lock remote control cable assembly to the front door lock with motor assembly.
69035A
3.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)
Engage the guides to install the front door lock cover sub-assembly to the front door lock with motor assembly.
|
Install in this Direction |
Engage the claws as shown in the illustration.
69040A
4.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY
When reusing a removed front door lock with motor assembly, replace the door lock wiring harness seal with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock with motor assembly.
Apply MP grease to the sliding parts of the front door lock with motor assembly.
When reusing the front door lock with motor assembly (w/o Double Locking System):
Install a new door lock wiring harness seal to the front door lock with motor assembly.
When reusing the front door lock with motor assembly (w/ Double Locking System):
Install a new door lock wiring harness seal to the front door lock with motor assembly.
| *1 | Front Door Lock Open Rod |
|
Install in this Direction |
Connect the front door lock open rod as shown in the illustration.
Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.
Connect the connector.
69217D
5.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
67404F
6.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
68151C
7.INSTALL FRONT DOOR GLASS RUN
67664
8.INSTALL DOOR FRAME UPPER GARNISH
68102
9.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
67832
10.INSTALL FRONT DOOR SERVICE HOLE COVER
68195
11.INSTALL FRONT DOOR BELT SEAL
68172A
12.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP
67602
13.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
74231
14.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
74232
15.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
69284C
16.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
17.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for 2ZR-FXE:
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION
for M20A-FXS:
Click hereGeneral>MAINTENANCE>M20A-FXS AUXILIARY BATTERY>INSTALLATION
18. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
19.INITIALIZE POWER WINDOW CONTROL SYSTEM
20.INSPECT POWER WINDOW OPERATION