Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2020.08
RM32K0E _59 Vehicle Exterior _061791 DOOR / HATCH _0304554 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75976G 1.INSTALL NO. 2 FRONT DOOR STRIPE (w/ Stripe Tape)

Hide 75986G 2.INSTALL FRONT DOOR OUTSIDE STRIPE (w/ Stripe Tape)

Hide 75966B 3.INSTALL NO. 4 FRONT DOOR STRIPE (w/ Stripe Tape)

Hide 75754A 4.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75752C 5.INSTALL FRONT DOOR FRONT WINDOW FRAME MOULDING

Hide 62112 6.INSTALL COWL SIDE TRIM BOARD

Hide 67914 7.INSTALL FRONT DOOR SCUFF PLATE

Hide 75720 8.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

Hide 9.INSTALL HOLE CAP

a.
B458110

Install the hole cap.


Hide 75072A 10.INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75732A 11.INSTALL FRONT DOOR OUTSIDE MOULDING

Hide 67001A 12.INSTALL FRONT DOOR PANEL CUSHION

a.
B458108

Engage the claws to install the 2 front door panel cushions.


Hide 68216 13.INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP

a.
B458107

Install the front door fix window weatherstrip to the front door fix window glass.


Hide 68126 14.INSTALL FRONT DOOR FIX WINDOW GLASS

a.
B458114C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door fix window glass with front door fix window weatherstrip as shown in the illustration.


Hide 86160 15.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67837B 16.INSTALL FRONT DOOR DUST PROOF SEAL (for TMMT Made)

a.
B458109

Install the 3 front door dust proof seals.


Hide 67837B 17.INSTALL FRONT DOOR DUST PROOF SEAL (for TMC Made)

a.
B621533

Install the 2 front door dust proof seals.

NOTICE:

Even if there were 3 dust proof seals at the time of removal, install 2 dust proof seals as shown in the illustration.



Hide 67862 18.INSTALL FRONT DOOR WEATHERSTRIP

a.
B458104C01
0.604,1.281 0.844,1.083 false 0.427,1.292 0.74,1.49 0.313,0.198 10 false *a
*a Clip (A)


Engage the clip (A) and other clip to install the front door weatherstrip.


Hide 68610 19.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt (A).


c.

Apply adhesive to the threads of the bolt (A).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B458103C01
3.063,1.26 3.229,1.427 0.167,0.167 10 true *a 1.333,1.625 1.5,1.792 0.167,0.167 10 true *b 1.344,0.385 1.51,0.552 0.167,0.167 10 true *b
*a Bolt (A)
*b Bolt (B)


Install the front door check assembly with the bolt (A) and 2 bolts (B).

Torque:
Bolt (A) : 30 N*m (306 kgf*cm, 22 ft.*lbf)
for TMMT Made Bolt (B) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
for TMC Made Bolt (B) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 69312 20.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B458115C01
1.75,1.917 2.156,1.802 true 1.573,1.813 1.75,2 0.177,0.188 10 true *a
*a Snap
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the snap to install the front door lock open rod to the front door outside frame sub-assembly as shown in the illustration.


Hide 69202A 21.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

w/ Protector:

i.
B458101

Install the door outside handle protector with the 3 screws.



b.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


c.

w/ Entry and Start System:

i.
B458116C02
0.438,1.25 0.635,0.979 false 1.573,1.313 1.573,1 false 2.375,1.292 2.375,0.979 false 1.542,1.375 1.854,1.573 0.313,0.198 10 false *a 2.333,1.375 2.646,1.573 0.313,0.198 10 false *b 0.302,1.292 0.615,1.49 0.313,0.198 10 false *b
*a Guide
*b Clamp


Engage the clamps and guide.


ii.
B458117C01
2,0.521 2.333,0.938 true 0.667,0.302 0.333,0.417 0.333,0.417 0.667,0.552 true 1.802,0.417 1.969,0.583 0.167,0.167 10 true *a 0.125,0.333 0.313,0.5 0.188,0.167 10 true *b
*a Grommet
*b Guide
V113147

Install in this Direction


Engage the grommet and guides to install the front door outside handle frame sub-assembly as shown in the illustration.


iii.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



d.

w/o Entry and Start System:

i.
B458118C01
2.583,1.531 2.51,1.125 true 0.667,0.531 0.375,0.417 0.375,0.417 0.656,0.323 true 2.521,1.542 2.781,1.76 0.26,0.219 10 true *a 0.177,0.323 0.344,0.542 0.167,0.219 10 true *b
*a Grommet
*b Guide
V113147

Install in this Direction


Engage the grommet and guides to install the front door outside handle frame sub-assembly as shown in the illustration.


ii.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



Hide 69040A 22.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69242E 23.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B458216C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the front door rear outside handle pad as shown in the illustration.


Hide 69241H 24.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B458217C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claws to install the front door front outside handle pad as shown in the illustration.


Hide 69220 25.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B458121C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door outside handle assembly as shown in the illustration.


b.
B458122

w/ Entry and Start System:

i.

Connect the connector.


ii.

Engage the claws.



Hide 69217D 26.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B458119C01
0.604,1.75 0.323,1.75 false 0.125,1.677 0.438,1.875 0.313,0.198 10 false *1
*1 Hole Plug
V113147

Remove in this Direction


Engage the claws to install the front door outside handle cover as shown in the illustration.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the hole plug.


Hide 69217D 27.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B392402C03
0,0 0,0 false
V113147

Install in this Direction


Engage the guides and claw to install the front door outside handle cover as shown in the illustration.


b.

Apply MP grease to the sliding area of the front door lock cylinder assembly.


c.
B458120C01
2.823,1.833 3.156,1.75 false 3.24,1.646 3.406,1.813 0.167,0.167 10 false *1
*1 Hole Plug
V113147

Install in this Direction


Install the front door outside handle cover with lock cylinder assembly as shown in the illustration.

HINT:

Check that the front door lock cylinder assembly is inserted into the front door lock with motor assembly.



d.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


e.

Install the hole plug.


Hide 67404F 28.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B458124C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide to install the front door rear lower frame sub-assembly.


b.

Install the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 67402F 29.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B458105

Temporarily install the front door front lower frame sub-assembly with the 2 bolts.


b.

Raise up the front door weatherstrip.


c.

Install the screw.


d.

Install the front door weatherstrip.


e.

Tighten the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68151C 30.INSTALL FRONT DOOR GLASS RUN

a.
B470603

Install the front door glass run.


Hide 67664 31.INSTALL DOOR FRAME UPPER GARNISH

a.
B458090

Engage the guides to install the door frame upper garnish.


Hide 32.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.
B458089C02
1.583,0.5 2.063,0.625 true 1.385,0.406 1.552,0.573 0.167,0.167 10 true *a 1.719,1.333 1.906,1.552 0.188,0.219 10 true 1 2.792,0.167 2.979,0.385 0.188,0.219 10 true 2 2.708,1.385 2.896,1.604 0.188,0.219 10 true 3 1.708,0.167 1.896,0.385 0.188,0.219 10 true 4
*a Temporary Bolt


Temporarily install the temporary bolt to the front door window regulator assembly.


c.

Temporarily install the front door window regulator assembly with the 5 bolts.


d.

Tighten the temporary bolt and 3 bolts to install the front door window regulator assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



e.

Tighten the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect the connector.


Hide 67831C 33.INSTALL NO. 2 FRONT DOOR SERVICE HOLE COVER

a.
B458088

Engage the claws to install the No. 2 front door service hole cover.


Hide 68102 34.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

for Driver Side:

i.

Connect the power window regulator master switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the power window regulator master switch assembly.



b.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the power window regulator switch assembly.



c.
B470604C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

NOTICE:

Be careful not to damage the front door glass sub-assembly.



d.
B470601

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
B458085

Install the hole plug.


Hide 67832 36.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B458127

Engage the clips to install the front door service hole cover.


b.

Insert the 3 front door weatherstrip clips and turn them 45° as shown in the illustration.


Hide 87912A 37.INSTALL OUTER MIRROR PROTECTOR

a.
B458128C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the outer mirror protector as shown in the illustration.


b.

Install the 2 screws.


Hide 87940 38.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 67838A 39.INSTALL FRONT DOOR VENT SEAL

a.
B458082

Install the front door vent seal.


Hide 68195 40.INSTALL FRONT DOOR BELT SEAL

a.
B458129C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door belt seal to the front door glass inner weatherstrip as shown in the illustration.


Hide 68172A 41.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B458130C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door glass inner weatherstrip with the front door belt seal as shown in the illustration.


Hide 67492A 42.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B458079

Engage the clips to install the front door lower frame bracket garnish.


Hide 81080S 43.INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Illumination)

Hide 69206B 44.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B458078

Engage the claw and guides to install the front door inside handle sub-assembly.


Hide 67602 45.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B458131C01
2.333,0.927 2.75,0.26 true 2.333,1.188 2.75,1.854 true 2.823,0.146 2.99,0.313 0.167,0.167 10 true *1 2.823,1.75 2.99,1.917 0.167,0.167 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Engage the guides to connect the front door lock remote control cable assembly and front door inside locking cable assembly as shown in the illustration.


b.

w/ Illumination:

i.

Connect the connector.



c.
B458214C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


d.
B458132C01
2.333,1.188 1.781,0.594 true 3.094,1.396 2.646,1.219 true 1.573,0.448 1.885,0.646 0.313,0.198 10 false *a 3.177,1.385 3.354,1.594 0.177,0.208 10 false *a
*a Clip (A)


Engage the clips (A), other clips and guide to install the front door trim board sub-assembly.


e.
B458075

Install the 3 screws.


Hide 74232 46.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

a.
B458218

Connect the 2 connectors.


b.
B458133C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides, clips and claws to install the multiplex network master switch assembly with front door upper armrest base panel as shown in the illustration.


Hide 74231 47.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

a.
B458219

Connect the connector.


b.
B458134C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides, clips and claws to install the power window regulator switch assembly with front door upper armrest base panel as shown in the illustration.


Hide 69284C 48.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B458135C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front door inside handle bezel plug as shown in the illustration.


Hide 49.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 50.INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 53.PERFORM CALIBRATION (w/ Panoramic View Monitor System)