Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat) › from 2020.08
RM32K0E _58 Vehicle Interior _061825 SEAT _0409031 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·
B407261

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.


HINT:
·

Power seat is available only on the driver side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY

a.
B557322

Place the front seat assembly in the vehicle as shown in the illustration.

NOTICE:
·

2 or more people are required when reinstalling the front seat assembly in to the vehicle.

·

Protect the front seat leg.

·

Be careful not to damage the front seat assembly, body exterior or body interior.




b.

Connect the front seat airbag assembly connector under the front seat assembly.

i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B345877C08
3.01,2.594 3.01,2.656 3.01,2.656 3.448,2.656 false 3,1.229 3,1.292 3,1.292 3.438,1.292 false 6.104,0.948 6.104,1.167 6.104,1.167 6.302,1.167 false 6.135,2.375 6.135,2.594 6.135,2.594 6.333,2.594 false 0.969,0.708 1.281,0.906 0.313,0.198 10 false *a 4.448,0.708 4.76,0.906 0.313,0.198 10 false *a 0.969,2.052 1.281,2.25 0.313,0.198 10 false *b 4.458,2.052 4.771,2.25 0.313,0.198 10 false *b 3.521,1.198 3.833,1.396 0.313,0.198 10 false *c 6.375,1.083 6.688,1.281 0.313,0.198 10 false *c 6.396,2.5 6.708,2.698 0.313,0.198 10 false *c 3.51,2.552 3.896,2.698 0.385,0.146 10 false *c
*a Correct *b Incorrect
*c Yellow CPA - -



ii.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.





c.

Connect each connector and engage each clamp under the front seat assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Temporarily install the front seat assembly with the 4 bolts.


f.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.


g.
B557320N01
0.26,0.854 0.417,1.052 0.156,0.198 10 true 1 1.74,1.875 1.896,2.073 0.156,0.198 10 true 2

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



h.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.


i.
B557319N01
3.104,1.323 3.26,1.521 0.156,0.198 10 true 1 0.208,1.313 0.365,1.51 0.156,0.198 10 true 2

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



Hide 72158 2.INSTALL INNER SEAT TRACK BRACKET COVER

a.
B557318

Engage the claws and guide to install the inner seat track bracket cover.


Hide 72138 3.INSTALL OUTER SEAT TRACK COVER

a.
B557317

Engage the claws and guide to install the outer seat track cover.


Hide 72128A 4.INSTALL FRONT INNER SEAT TRACK BRACKET COVER

a.

Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.


b.
B557316

Engage the claws to install the front inner seat track bracket cover.


Hide 72124 5.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER

a.
B557315

Engage the claws to install the front outer seat track bracket cover.


Hide 71910A 6.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly to the front seat assembly.


Hide 7. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART