Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.09–2022.01
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 1 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

Millimeter wave radar sensor assembly

(w/ Toyota Safety Sense)

·

Forward recognition camera

(w/ Toyota Safety Sense)

·

Clearance warning ECU assembly

(w/ TOYOTA Parking Assist-sensor System)

·

Parking assist ECU

(w/ Panoramic View Monitor System)

·

Blind spot monitor sensor LH

(w/ Blind Spot Monitor System)

·

No. 1 CAN junction connector

·

No. 6 CAN junction connector

(w/ Blind Spot Monitor System)



WIRING DIAGRAM

for TMMT Made without Blind Spot Monitor System


C360936E12
0.677,0.979 1.448,1.177 0.771,0.198 10 false 120 Ω 0.677,5.271 1.448,5.469 0.771,0.198 10 false 120 Ω 1.375,0.625 2.146,0.823 0.771,0.198 10 false CA1H 1.354,1.156 2.125,1.354 0.771,0.198 10 false CA1L 1.354,4.906 2.125,5.104 0.771,0.198 10 false CAXH 1.354,5.438 2.125,5.635 0.771,0.198 10 false CAXL 1.854,0.615 2.125,0.813 0.271,0.198 10 false 23 1.854,1.156 2.125,1.354 0.271,0.198 10 false 8 1.854,4.906 2.125,5.104 0.271,0.198 10 false 9 1.854,5.448 2.125,5.646 0.271,0.198 10 false 24 2.813,5.448 3.083,5.646 0.271,0.198 10 false 20 2.813,4.906 3.083,5.104 0.271,0.198 10 false 10 2.802,1.156 3.073,1.354 0.271,0.198 10 false 19 2.875,0.615 3.146,0.813 0.271,0.198 10 false 9 4.188,0.615 4.458,0.813 0.271,0.198 10 false 3 4.198,1.156 4.469,1.354 0.271,0.198 10 false 13 5.219,0.615 5.49,0.813 0.271,0.198 10 false 3 5.219,1.156 5.49,1.354 0.271,0.198 10 false 2 5.448,0.708 6.219,0.906 0.771,0.198 10 false CA2H 5.448,1.24 6.219,1.438 0.771,0.198 10 false CA2L 5.188,1.802 6.688,2.344 1.5,0.542 10 false Millimeter Wave Radar Sensor Assembly*1 5.188,1.635 5.958,1.833 0.771,0.198 10 false A2 4.188,2.76 4.458,2.958 0.271,0.198 10 false 2 4.177,3.292 4.448,3.49 0.271,0.198 10 false 12 4.188,4.906 4.458,5.104 0.271,0.198 10 false 1 4.188,5.438 4.458,5.635 0.271,0.198 10 false 11 5.219,2.76 5.49,2.958 0.271,0.198 10 false 5 5.146,3.292 5.417,3.49 0.271,0.198 10 false 11 5.146,5.438 5.417,5.635 0.271,0.198 10 false 18 5.146,4.906 5.417,5.104 0.271,0.198 10 false 17 5.448,2.865 6.219,3.063 0.771,0.198 10 false CA1P 5.448,3.396 6.219,3.594 0.771,0.198 10 false CA1N 5.448,5 6.219,5.198 0.771,0.198 10 false R1 5.448,5.542 6.219,5.74 0.771,0.198 10 false R2 5.271,3.938 6.583,4.5 1.313,0.563 10 false Forward Recognition Camera*1 5.271,3.781 6.042,3.979 0.771,0.198 10 false R5 5.313,6.083 6.552,6.698 1.24,0.615 10 false Clearance Warning ECU Assembly*2 5.313,5.927 6.083,6.125 0.771,0.198 10 false F142 2.594,5.896 3.365,6.094 0.771,0.198 10 false F111 2.594,6.063 4.625,6.698 2.031,0.635 10 false No. 1 CAN Junction Connector 0.188,6.083 2.167,6.479 1.979,0.396 10 false Central Gateway ECU (Network Gateway ECU) 0.188,5.917 0.958,6.115 0.771,0.198 10 false F74 0.177,6.917 4.156,7.115 3.979,0.198 10 false *1: w/ Toyota Safety Sense 0.177,7.25 4.156,7.448 3.979,0.198 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.073,0.042 1.542,0.281 1.469,0.24 12 false for LHD:

C360936E13
0.677,0.979 1.448,1.177 0.771,0.198 10 false 120 Ω 0.677,5.271 1.448,5.469 0.771,0.198 10 false 120 Ω 1.354,0.615 2.125,0.813 0.771,0.198 10 false CA1H 1.354,1.156 2.125,1.354 0.771,0.198 10 false CA1L 1.354,4.906 2.125,5.104 0.771,0.198 10 false CAXH 1.354,5.438 2.125,5.635 0.771,0.198 10 false CAXL 1.854,0.615 2.125,0.813 0.271,0.198 10 false 23 1.854,1.156 2.125,1.354 0.271,0.198 10 false 8 1.854,4.906 2.125,5.104 0.271,0.198 10 false 9 1.854,5.448 2.125,5.646 0.271,0.198 10 false 24 2.813,5.448 3.083,5.646 0.271,0.198 10 false 11 2.875,4.906 3.146,5.104 0.271,0.198 10 false 5 2.802,1.156 3.073,1.354 0.271,0.198 10 false 12 2.875,0.615 3.146,0.813 0.271,0.198 10 false 6 4.188,0.615 4.458,0.813 0.271,0.198 10 false 3 4.198,1.156 4.469,1.354 0.271,0.198 10 false 9 5.219,0.615 5.49,0.813 0.271,0.198 10 false 3 5.219,1.156 5.49,1.354 0.271,0.198 10 false 2 5.448,0.708 6.219,0.906 0.771,0.198 10 false CA2H 5.448,1.24 6.219,1.438 0.771,0.198 10 false CA2L 5.188,1.802 6.688,2.344 1.5,0.542 10 false Millimeter Wave Radar Sensor Assembly*1 5.188,1.635 5.958,1.833 0.771,0.198 10 false A2 4.188,2.76 4.458,2.958 0.271,0.198 10 false 2 4.177,3.292 4.448,3.49 0.271,0.198 10 false 8 4.188,4.906 4.458,5.104 0.271,0.198 10 false 1 4.188,5.438 4.458,5.635 0.271,0.198 10 false 7 5.219,2.76 5.49,2.958 0.271,0.198 10 false 5 5.146,3.292 5.417,3.49 0.271,0.198 10 false 11 5.146,5.438 5.417,5.635 0.271,0.198 10 false 18 5.146,4.906 5.417,5.104 0.271,0.198 10 false 17 5.448,2.865 6.219,3.063 0.771,0.198 10 false CA1P 5.448,3.396 6.219,3.594 0.771,0.198 10 false CA1N 5.448,5 6.219,5.198 0.771,0.198 10 false R1 5.448,5.542 6.219,5.74 0.771,0.198 10 false R2 5.271,3.938 6.583,4.5 1.313,0.563 10 false Forward Recognition Camera*1 5.271,3.781 6.042,3.979 0.771,0.198 10 false R5 5.313,6.083 6.552,6.698 1.24,0.615 10 false Clearance Warning ECU Assembly*2 5.313,5.927 6.083,6.125 0.771,0.198 10 false F142 2.594,5.896 3.365,6.094 0.771,0.198 10 false F164 2.594,6.063 4.625,6.698 2.031,0.635 10 false No. 1 CAN Junction Connector 0.188,6.083 2.167,6.479 1.979,0.396 10 false Central Gateway ECU (Network Gateway ECU) 0.188,5.917 0.958,6.115 0.771,0.198 10 false F74 0.177,6.917 4.156,7.115 3.979,0.198 10 false *1: w/ Toyota Safety Sense 0.177,7.25 4.156,7.448 3.979,0.198 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.063,0.042 1.531,0.281 1.469,0.24 12 false for RHD:


for TMMT Made with Blind Spot Monitor System


C360938E08
1.354,0.708 1.969,0.906 0.615,0.198 10 false CA2H 1.354,1.25 1.969,1.448 0.615,0.198 10 false CA2L 1.854,0.615 2.219,0.854 0.365,0.24 10 false 3 1.854,1.146 2.219,1.385 0.365,0.24 10 false 2 1.854,2.76 2.219,3 0.365,0.24 10 false 9 1.854,3.281 2.219,3.521 0.365,0.24 10 false 24 1.854,5.396 2.219,5.635 0.365,0.24 10 false 23 1.854,5.927 2.219,6.167 0.365,0.24 10 false 8 1.354,2.76 1.969,2.958 0.615,0.198 10 false CAXH 1.354,3.292 1.969,3.49 0.615,0.198 10 false CAXL 1.354,5.396 1.969,5.594 0.615,0.198 10 false CA1H 1.354,5.927 1.969,6.125 0.615,0.198 10 false CA1L 0.698,3.125 1.313,3.323 0.615,0.198 10 false 120 Ω 0.698,5.771 1.313,5.969 0.615,0.198 10 false 120 Ω 0.208,6.583 2.177,7.031 1.969,0.448 10 false Central Gateway ECU (Network Gateway ECU) 0.208,6.417 0.583,6.667 0.375,0.25 10 false F74 2.688,0.615 3.052,0.854 0.365,0.24 10 false 3 2.615,1.146 2.979,1.385 0.365,0.24 10 false 13 2.625,2.76 2.99,3 0.365,0.24 10 false 10 2.615,3.292 2.979,3.531 0.365,0.24 10 false 20 2.615,5.938 2.979,6.177 0.365,0.24 10 false 21 2.604,5.396 2.969,5.635 0.365,0.24 10 false 10 2.333,4.479 4.313,4.771 1.979,0.292 10 false No. 1 CAN Junction Connector 2.333,4.313 2.948,4.49 0.615,0.177 10 false F111 2.333,7.656 4.625,7.948 2.292,0.292 10 false No. 6 CAN Junction Connector 2.333,7.49 2.948,7.667 0.615,0.177 10 false M104 3.99,0.615 4.396,0.813 0.406,0.198 10 false 2 3.99,1.146 4.448,1.323 0.458,0.177 10 false 12 3.99,2.76 4.396,2.948 0.406,0.188 10 false 1 3.99,3.292 4.406,3.469 0.417,0.177 10 false 11 3.99,3.563 4.5,3.75 0.51,0.188 10 false 19 3.99,3.823 4.448,4.01 0.458,0.188 10 false 9 3.99,5.396 4.458,5.583 0.469,0.188 10 false 11 3.99,5.927 4.427,6.115 0.438,0.188 10 false 22 4,6.469 4.469,6.646 0.469,0.177 10 false 9 3.99,7 4.406,7.177 0.417,0.177 10 false 20 5.219,0.615 5.625,0.813 0.406,0.198 10 false 5 5.146,1.156 5.552,1.354 0.406,0.198 10 false 11 5.146,2.76 5.552,2.958 0.406,0.198 10 false 17 5.146,3.292 5.552,3.49 0.406,0.198 10 false 18 5.219,6.469 5.625,6.667 0.406,0.198 10 false 2 5.219,7 5.625,7.198 0.406,0.198 10 false 7 5.448,0.719 6.063,0.917 0.615,0.198 10 false CA1P 5.448,1.25 6.052,1.448 0.604,0.198 10 false CA1N 5.448,2.854 6.083,3.073 0.635,0.219 10 false R1 5.448,3.385 6.01,3.625 0.563,0.24 10 false R2 5.448,6.563 6.104,6.771 0.656,0.208 10 false CA1P 5.448,7.104 6.104,7.302 0.656,0.198 10 false CA1N 5.292,1.635 5.896,1.833 0.604,0.198 10 false R5 5.292,1.792 6.604,2.323 1.313,0.531 10 false Forward Recognition Camera*1 5.313,3.927 6.542,4.458 1.229,0.531 10 false Clearance Warning ECU Assembly*2 5.313,3.771 5.875,4.01 0.563,0.24 10 false F142 5.344,7.656 6.563,8.188 1.219,0.531 10 false Blind Spot Monitor Sensor LH 5.344,7.49 6,7.688 0.656,0.198 10 false M62 0.208,7.417 2.5,7.708 2.292,0.292 10 false *1: w/ Toyota Safety Sense 0.208,7.75 1.698,8.313 1.49,0.563 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.552,1.635 1.167,1.833 0.615,0.198 10 false A2 0.552,1.802 1.979,2.396 1.427,0.594 10 false Millimeter Wave Radar Sensor Assembly*1 0.063,0.031 2.635,0.271 2.573,0.24 12 false for LHD:

C360938E09
1.354,0.708 1.969,0.906 0.615,0.198 10 false CA2H 1.354,1.25 1.969,1.448 0.615,0.198 10 false CA2L 1.854,0.615 2.219,0.854 0.365,0.24 10 false 3 1.854,1.146 2.219,1.385 0.365,0.24 10 false 2 1.854,2.76 2.219,3 0.365,0.24 10 false 9 1.854,3.281 2.219,3.521 0.365,0.24 10 false 24 1.854,5.396 2.219,5.635 0.365,0.24 10 false 23 1.854,5.927 2.219,6.167 0.365,0.24 10 false 8 1.354,2.76 1.969,2.958 0.615,0.198 10 false CAXH 1.354,3.292 1.969,3.49 0.615,0.198 10 false CAXL 1.354,5.396 1.969,5.594 0.615,0.198 10 false CA1H 1.354,5.927 1.969,6.125 0.615,0.198 10 false CA1L 0.698,3.125 1.313,3.323 0.615,0.198 10 false 120 Ω 0.698,5.771 1.313,5.969 0.615,0.198 10 false 120 Ω 0.208,6.583 2.177,7.031 1.969,0.448 10 false Central Gateway ECU (Network Gateway ECU) 0.208,6.417 0.583,6.667 0.375,0.25 10 false F74 2.688,0.615 3.052,0.854 0.365,0.24 10 false 3 2.698,1.146 3.063,1.385 0.365,0.24 10 false 9 2.708,2.76 2.99,3 0.281,0.24 10 false 6 2.646,3.292 2.979,3.542 0.333,0.25 10 false 12 2.615,5.938 2.979,6.177 0.365,0.24 10 false 21 2.604,5.396 2.969,5.635 0.365,0.24 10 false 10 2.333,4.479 4.313,4.771 1.979,0.292 10 false No. 1 CAN Junction Connector 2.333,4.313 2.948,4.49 0.615,0.177 10 false F164 2.333,7.656 4.625,7.948 2.292,0.292 10 false No. 6 CAN Junction Connector 2.333,7.49 2.948,7.667 0.615,0.177 10 false M104 3.99,0.615 4.396,0.813 0.406,0.198 10 false 2 3.99,1.146 4.448,1.323 0.458,0.177 10 false 8 3.99,2.76 4.396,2.948 0.406,0.188 10 false 1 3.99,3.292 4.406,3.469 0.417,0.177 10 false 7 3.99,3.563 4.5,3.75 0.51,0.188 10 false 11 3.99,3.823 4.448,4.01 0.458,0.188 10 false 5 3.99,5.396 4.458,5.583 0.469,0.188 10 false 11 3.99,5.927 4.427,6.115 0.438,0.188 10 false 22 4,6.469 4.469,6.646 0.469,0.177 10 false 9 3.99,7 4.406,7.177 0.417,0.177 10 false 20 5.219,0.615 5.625,0.813 0.406,0.198 10 false 5 5.146,1.156 5.552,1.354 0.406,0.198 10 false 11 5.146,2.76 5.552,2.958 0.406,0.198 10 false 17 5.146,3.292 5.552,3.49 0.406,0.198 10 false 18 5.219,6.469 5.625,6.667 0.406,0.198 10 false 2 5.219,7 5.625,7.198 0.406,0.198 10 false 7 5.448,0.719 6.063,0.917 0.615,0.198 10 false CA1P 5.448,1.25 6.052,1.448 0.604,0.198 10 false CA1N 5.448,2.854 6.083,3.073 0.635,0.219 10 false R1 5.448,3.385 6.01,3.625 0.563,0.24 10 false R2 5.448,6.563 6.104,6.771 0.656,0.208 10 false CA1P 5.448,7.104 6.104,7.302 0.656,0.198 10 false CA1N 5.292,1.635 5.896,1.833 0.604,0.198 10 false R5 5.292,1.792 6.604,2.323 1.313,0.531 10 false Forward Recognition Camera*1 5.313,3.927 6.542,4.458 1.229,0.531 10 false Clearance Warning ECU Assembly*2 5.313,3.771 5.875,4.01 0.563,0.24 10 false F142 5.344,7.656 6.563,8.188 1.219,0.531 10 false Blind Spot Monitor Sensor LH 5.344,7.49 6,7.688 0.656,0.198 10 false M62 0.208,7.417 2.5,7.708 2.292,0.292 10 false *1: w/ Toyota Safety Sense 0.208,7.75 1.698,8.313 1.49,0.563 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.552,1.635 1.167,1.833 0.615,0.198 10 false A2 0.552,1.802 1.979,2.396 1.427,0.594 10 false Millimeter Wave Radar Sensor Assembly*1 0.063,0.031 2.635,0.271 2.573,0.24 12 false for RHD:


for TMC Made


C360938E10
1.354,0.708 1.969,0.906 0.615,0.198 10 false CA2H 1.354,1.25 1.969,1.448 0.615,0.198 10 false CA2L 1.854,0.615 2.219,0.854 0.365,0.24 10 false 3 1.854,1.146 2.219,1.385 0.365,0.24 10 false 2 1.854,2.76 2.219,3 0.365,0.24 10 false 9 1.854,3.281 2.219,3.521 0.365,0.24 10 false 24 1.854,5.396 2.219,5.635 0.365,0.24 10 false 23 1.854,5.927 2.219,6.167 0.365,0.24 10 false 8 1.354,2.76 1.969,2.958 0.615,0.198 10 false CAXH 1.354,3.292 1.969,3.49 0.615,0.198 10 false CAXL 1.354,5.396 1.969,5.594 0.615,0.198 10 false CA1H 1.354,5.927 1.969,6.125 0.615,0.198 10 false CA1L 0.698,3.125 1.313,3.323 0.615,0.198 10 false 120 Ω 0.698,5.771 1.313,5.969 0.615,0.198 10 false 120 Ω 0.208,6.583 2.177,7.031 1.969,0.448 10 false Central Gateway ECU (Network Gateway ECU) 0.208,6.417 0.583,6.667 0.375,0.25 10 false F74 2.688,0.615 3.052,0.854 0.365,0.24 10 false 3 2.615,1.146 2.979,1.385 0.365,0.24 10 false 14 2.708,2.76 2.99,3 0.281,0.24 10 false 5 2.646,3.292 2.979,3.542 0.333,0.25 10 false 16 2.615,5.938 2.979,6.177 0.365,0.24 10 false 19 2.667,5.396 2.969,5.635 0.302,0.24 10 false 8 2.333,4.479 4.313,4.771 1.979,0.292 10 false No. 1 CAN Junction Connector 2.333,4.313 2.948,4.49 0.615,0.177 10 false F177 2.333,7.656 4.625,7.948 2.292,0.292 10 false No. 6 CAN Junction Connector 2.333,7.49 2.948,7.667 0.615,0.177 10 false M104 3.99,0.615 4.396,0.813 0.406,0.198 10 false 2 3.99,1.146 4.448,1.323 0.458,0.177 10 false 13 3.99,2.76 4.396,2.948 0.406,0.188 10 false 1 3.99,3.292 4.406,3.469 0.417,0.177 10 false 12 3.99,3.563 4.5,3.75 0.51,0.188 10 false 15 3.99,3.823 4.448,4.01 0.458,0.188 10 false 4 3.99,5.396 4.458,5.583 0.469,0.188 10 false 11 3.99,5.927 4.427,6.115 0.438,0.188 10 false 22 4,6.469 4.469,6.646 0.469,0.177 10 false 9 3.99,7 4.406,7.177 0.417,0.177 10 false 20 5.219,0.615 5.625,0.813 0.406,0.198 10 false 5 5.146,1.156 5.552,1.354 0.406,0.198 10 false 11 5.146,2.76 5.552,2.958 0.406,0.198 10 false 17 5.146,3.292 5.552,3.49 0.406,0.198 10 false 18 5.219,6.469 5.625,6.667 0.406,0.198 10 false 2 5.219,7 5.625,7.198 0.406,0.198 10 false 7 5.448,0.719 6.063,0.917 0.615,0.198 10 false CA1P 5.448,1.25 6.052,1.448 0.604,0.198 10 false CA1N 5.448,2.854 6.083,3.073 0.635,0.219 10 false R1 5.448,3.385 6.01,3.625 0.563,0.24 10 false R2 5.448,6.563 6.104,6.771 0.656,0.208 10 false CA1P 5.448,7.104 6.104,7.302 0.656,0.198 10 false CA1N 5.292,1.635 5.896,1.833 0.604,0.198 10 false R5 5.292,1.792 6.604,2.323 1.313,0.531 10 false Forward Recognition Camera 5.313,3.927 6.542,4.458 1.229,0.531 10 false Clearance Warning ECU Assembly*1 5.313,3.771 5.875,4.01 0.563,0.24 10 false F142 5.344,7.656 6.563,8.188 1.219,0.531 10 false Blind Spot Monitor Sensor LH 5.344,7.49 6,7.688 0.656,0.198 10 false M62 0.208,7.75 1.698,8.313 1.49,0.563 10 false *1: w/ TOYOTA Parking Assist-sensor System 0.552,1.635 1.167,1.833 0.615,0.198 10 false A2 0.552,1.802 1.979,2.396 1.427,0.594 10 false Millimeter Wave Radar Sensor Assembly 0.063,0.031 3.281,0.323 3.219,0.292 12 false w/o Panoramic View Monitor System:

C366135E16
1.385,0.615 2,0.813 0.615,0.198 10 false CA1H 0.698,0.979 1.313,1.177 0.615,0.198 10 false 120 Ω 0.667,3.719 1.281,3.917 0.615,0.198 10 false 120 Ω 1.385,1.167 2,1.365 0.615,0.198 10 false CA1L 1.365,3.365 1.979,3.563 0.615,0.198 10 false CAXH 1.375,3.906 1.99,4.104 0.615,0.198 10 false CAXL 1.833,0.604 2.083,0.802 0.25,0.198 10 false 23 1.854,1.156 2.104,1.354 0.25,0.198 10 false 8 1.875,3.354 2.125,3.552 0.25,0.198 10 false 9 1.844,3.885 2.094,4.083 0.25,0.198 10 false 24 2.74,0.615 2.99,0.813 0.25,0.198 10 false 8 2.635,1.167 2.906,1.385 0.271,0.219 10 false 19 3.979,0.604 4.229,0.802 0.25,0.198 10 false 9 3.979,1.156 4.229,1.354 0.25,0.198 10 false 20 4,1.458 4.25,1.656 0.25,0.198 10 false 22 3.99,1.781 4.24,1.979 0.25,0.198 10 false 11 5.219,0.615 5.469,0.813 0.25,0.198 10 false 2 5.219,1.156 5.469,1.354 0.25,0.198 10 false 7 5.438,0.719 6.021,0.917 0.583,0.198 10 false CA1P 5.438,1.25 6.021,1.448 0.583,0.198 10 false CA1N 5.177,1.615 5.76,1.813 0.583,0.198 10 false M62 5.177,1.771 7.104,2.021 1.927,0.25 10 false Blind Spot Monitor Sensor LH 4,3.344 4.25,3.542 0.25,0.198 10 false 5 3.979,3.906 4.229,4.104 0.25,0.198 10 false 11 2.635,3.896 2.885,4.094 0.25,0.198 10 false 12 2.698,3.365 2.948,3.563 0.25,0.198 10 false 6 0.344,4.344 0.677,4.542 0.333,0.198 10 false F74 0.333,4.51 2.333,4.875 2,0.365 10 false Central Gateway ECU (Network Gateway ECU) 2.438,2.229 2.854,2.479 0.417,0.25 10 false M104 2.438,2.396 4.438,2.646 2,0.25 10 false No. 6 CAN Junction Connector 3.99,4.604 5.99,4.854 2,0.25 10 false No. 1 CAN Junction Connector 3.99,4.438 4.573,4.635 0.583,0.198 10 false F164 0.063,0.042 3.115,0.281 3.052,0.24 12 false w/ Panoramic View Monitor System:

C366136E12
1.365,1.26 1.979,1.458 0.615,0.198 10 false CA2H 1.396,1.781 2.01,1.979 0.615,0.198 10 false CA2L 0.583,2.146 1.198,2.344 0.615,0.198 10 false A2 0.563,2.313 2.479,2.729 1.917,0.417 10 false Millimeter Wave Radar Sensor Assembly*1 1.833,1.135 2.083,1.302 0.25,0.167 10 false 3 1.854,1.688 2.104,1.854 0.25,0.167 10 false 2 2.708,1.135 2.958,1.302 0.25,0.167 10 false 3 2.698,1.688 2.948,1.854 0.25,0.167 10 false 9 3.99,1.135 4.24,1.302 0.25,0.167 10 false 1 3.99,1.667 4.24,1.833 0.25,0.167 10 false 7 5,1.146 5.25,1.313 0.25,0.167 10 false 17 4.99,1.667 5.24,1.833 0.25,0.167 10 false 18 5.26,1.25 5.594,1.417 0.333,0.167 10 false R1 5.26,1.792 5.594,1.958 0.333,0.167 10 false R2 5.083,2.146 5.417,2.313 0.333,0.167 10 false F142 5.083,2.302 6.667,2.719 1.583,0.417 10 false Clearance Warning ECU Assembly*2 5.01,3.302 5.26,3.469 0.25,0.167 10 false 40 4.99,3.802 5.24,3.969 0.25,0.167 10 false 18 5.25,3.396 5.833,3.563 0.583,0.167 10 false CANH 5.25,3.938 5.833,4.104 0.583,0.167 10 false CANL 5.063,4.292 5.646,4.458 0.583,0.167 10 false M116 5.073,4.469 7.156,4.719 2.083,0.25 10 false Parking Assist ECU 2.573,4.292 3.156,4.458 0.583,0.167 10 false F164 2.594,4.448 4.594,4.698 2,0.25 10 false No. 1 CAN Junction Connector 4,3.281 4.25,3.448 0.25,0.167 10 false 4 3.979,3.823 4.229,3.99 0.25,0.167 10 false 10 2.698,3.281 2.948,3.448 0.25,0.167 10 false 2 2.677,3.813 2.927,3.979 0.25,0.167 10 false 8 1.854,3.292 2.104,3.458 0.25,0.167 10 false 5 1.844,3.813 2.094,3.979 0.25,0.167 10 false 11 1.365,3.417 1.948,3.583 0.583,0.167 10 false CA1P 1.354,3.917 1.938,4.083 0.583,0.167 10 false CA1N 0.417,4.26 1,4.427 0.583,0.167 10 false R5 0.427,4.417 2.427,4.667 2,0.25 10 false Forward Recognition Camera*1 0.417,4.948 2.417,5.198 2,0.25 10 false *1: w/ Toyota Safety Sense 0.417,5.281 4,5.531 3.583,0.25 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.073,0.063 2.927,0.344 2.854,0.281 12 false w/ Panoramic View Monitor System:


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK VEHICLE TYPE

B

10.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Blind Spot Monitor System A
w/ Blind Spot Monitor System B



A

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

B

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C328881C41
3.313,0.385 3.813,0.635 0.5,0.25 2.135,2.094 2.406,1.635 true 2.469,2.167 2.729,1.677 true 1.781,0.844 2.385,1.396 true 2.125,0.594 2.74,1.406 true 4.74,1.417 5.552,0.594 true 4.708,1.646 5.542,2.333 true 1.656,1.219 2.073,1.396 true 1.667,1.802 2.125,1.625 true 5.083,1.625 5.677,2 true 5.083,1.406 5.635,1.146 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 1.583,2.021 2.167,2.25 0.583,0.229 10 false CANL*c 1.563,0.458 2.281,0.719 0.719,0.26 10 false CANH*d 5.625,0.5 6.208,0.813 0.583,0.313 10 false CANH*e 2.115,2.219 2.667,2.469 0.552,0.25 10 false CANL*d 1.219,0.76 1.948,0.99 0.729,0.229 10 false CANH*c 5.604,2.26 6.188,2.51 0.583,0.25 10 false CANL*e 3.406,0.417 4.094,0.708 0.688,0.292 10 false F111 1.073,1.115 1.844,1.313 0.771,0.198 10 false CANH*b 1.094,1.74 1.865,1.938 0.771,0.198 10 false CANL*b 5.75,1.906 6.333,2.156 0.583,0.25 10 false CANL*e 5.708,1.052 6.292,1.365 0.583,0.313 10 false CANH*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F111-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance Warning ECU Assembly*1
F111-2 (CANH) - F111-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward Recognition Camera*2
F111-3 (CANH) - F111-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly*2
F111-9 (CANH) - F111-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central Gateway ECU (Network Gateway ECU)
F111-10 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central Gateway ECU (Network Gateway ECU)


*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

9.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
4.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C328881C42
3.313,0.385 3.813,0.635 0.5,0.25 4.74,1.417 5.552,0.594 true 4.708,1.646 5.542,2.333 true 5.083,1.625 5.677,2 true 5.083,1.406 5.635,1.146 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 5.625,0.5 6.208,0.813 0.583,0.313 10 false CANH*b 5.604,2.26 6.188,2.51 0.583,0.25 10 false CANL*b 3.406,0.417 4.094,0.708 0.688,0.292 10 false F111 5.75,1.906 6.333,2.156 0.583,0.25 10 false CANL*b 5.708,1.052 6.292,1.365 0.583,0.313 10 false CANH*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F111-9 (CANH) - F111-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
F111-10 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 6 CAN junction connector.


c.
C425651C05
1.417,0.75 1.917,1 0.5,0.25 2.323,1.75 2.677,0.969 true 2.49,1.76 2.729,1.333 true 2.656,2.615 2.313,2.01 true 2.729,2.333 2.5,2 true 2.146,1.771 2.479,0.729 true 2.375,2.76 2.167,2 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.479,0.792 1.875,0.958 0.396,0.167 10 false M104 2.792,1.188 3.344,1.438 0.552,0.25 10 false CANH*d 2.51,0.563 3.156,0.729 0.646,0.167 10 false CANH*b 2.344,2.833 2.99,3 0.646,0.167 10 false CANL*b 2.771,2.26 3.323,2.427 0.552,0.167 10 false CANL*d 2.719,2.563 3.271,2.729 0.552,0.167 10 false CANL*c 2.75,0.833 3.302,1.083 0.552,0.25 10 false CANH*c
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH
*c to Central Gateway ECU (Network Gateway ECU)
*d to No. 1 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M104-9 (CANH) - M104-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH
M104-10 (CANH) - M104-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M104-11 (CANH) - M104-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

7.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
6.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C425651C06
1.417,0.75 1.917,1 0.5,0.25 2.323,1.76 2.656,1.135 true 2.583,2.563 2.313,2 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.5,0.792 1.896,0.958 0.396,0.167 10 false M104 2.74,0.969 3.385,1.135 0.646,0.167 10 false CANH*b 2.646,2.5 3.292,2.667 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M104-10 (CANH) - M104-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

7.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C328881C43
3.313,0.385 3.813,0.635 0.5,0.25 2.135,2.094 2.417,1.635 true 2.469,2.167 2.76,1.635 true 1.781,0.844 2.417,1.406 true 2.115,0.583 2.74,1.396 true 4.74,1.417 5.552,0.594 true 4.708,1.646 5.542,2.333 true 1.656,1.219 2.052,1.396 true 1.667,1.792 2.052,1.625 true 5.083,1.625 5.677,2 true 5.083,1.406 5.635,1.146 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 1.583,2.021 2.167,2.25 0.583,0.229 10 false CANL*c 1.563,0.458 2.281,0.719 0.719,0.26 10 false CANH*d 5.625,0.5 6.208,0.813 0.583,0.313 10 false CANH*e 2.115,2.219 2.667,2.469 0.552,0.25 10 false CANL*d 1.219,0.76 1.948,0.99 0.729,0.229 10 false CANH*c 5.604,2.26 6.188,2.51 0.583,0.25 10 false CANL*e 3.406,0.417 4.094,0.708 0.688,0.292 10 false F111 1.073,1.115 1.844,1.313 0.771,0.198 10 false CANH*b 1.094,1.74 1.865,1.938 0.771,0.198 10 false CANL*b 5.75,1.906 6.333,2.156 0.583,0.25 10 false CANL*f 5.698,1.042 6.281,1.354 0.583,0.313 10 false CANH*f
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to No. 6 CAN Junction Connector *f to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F111-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance Warning ECU Assembly*1
F111-2 (CANH) - F111-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward Recognition Camera*2
F111-3 (CANH) - F111-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly*2
F111-9 (CANH) - F111-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector
F111-10 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central Gateway ECU (Network Gateway ECU)


*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 6 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

8.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
8.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C328881C44
3.313,0.385 3.813,0.635 0.5,0.25 5.083,1.625 5.677,2 true 5.083,1.406 5.635,1.146 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 3.406,0.417 4.094,0.708 0.688,0.292 10 false F111 5.75,1.906 6.333,2.156 0.583,0.25 10 false CANL*b 5.708,1.052 6.292,1.365 0.583,0.313 10 false CANH*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F111-10 (CANH) - F111-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

9.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367281C01
1.417,0.333 1.917,0.583 0.5,0.25 1.208,0.958 0.917,0.417 true 0.917,1.75 1.177,1.135 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.521,0.323 1,0.521 0.479,0.198 10 false CA1L 0.615,1.781 1.094,1.979 0.479,0.198 10 false CA1H 1.552,0.375 2.031,0.573 0.479,0.198 10 false F74
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
expect TMC Made without Panoramic View Monitor System A
for TMC Made without Panoramic ViewMonitor System B



A

11.CHECK VEHICLE TYPE

B

19.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
11.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Blind Spot Monitor System A
w/ Blind Spot Monitor System B



A

12.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

B

14.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C404458C49
3.313,0.188 3.813,0.438 0.5,0.25 2.25,1 2.677,1.427 true 2.25,2.083 2.688,1.646 true 3.385,1.417 2.875,0.479 true 2.583,2.333 3.021,1.656 true 2.969,2.5 3.385,1.656 true 2.583,0.708 3.01,1.417 true 4.042,1.438 4.427,0.74 true 4.042,1.646 4.531,2.344 true 4.385,1.417 4.833,1 true 4.385,1.656 4.833,2.083 true 1.688,0.896 2.604,1.094 0.917,0.198 10 false CANH*b 1.708,2 2.625,2.198 0.917,0.198 10 false CANL*b 4.896,0.906 5.813,1.104 0.917,0.198 10 false CANH*e 0.26,0.219 0.594,0.427 0.333,0.208 10 false *a 3.396,0.208 3.771,0.417 0.375,0.208 10 false F164 2.031,0.615 2.635,0.802 0.604,0.188 10 false CANH*c 2.042,2.271 2.958,2.469 0.917,0.198 10 false CANL*c 2.313,0.344 3.229,0.542 0.917,0.198 10 false CANH*d 2.458,2.5 3.375,2.698 0.917,0.198 10 false CANL*d 4.49,0.646 5.406,0.844 0.917,0.198 10 false CANH*e 4.583,2.292 5.5,2.49 0.917,0.198 10 false CANL*e 4.917,2.01 5.833,2.208 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F164-1 (CANH) - F164-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance Warning ECU Assembly*1
F164-2 (CANH) - F164-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward Recognition Camera*2
F164-3 (CANH) - F164-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly*2
F164-5 (CANH) - F164-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central Gateway ECU (Network Gateway ECU)
F164-6 (CANH) - F164-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central Gateway ECU (Network Gateway ECU)


*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

13.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

18.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
13.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C404458C50
3.271,0.583 3.771,0.833 0.5,0.25 4.042,1.427 4.625,0.792 true 4.354,1.448 4.885,1.052 true 4.375,1.635 4.896,1.823 true 4.021,1.625 4.646,2.188 true 0.104,0.135 0.406,0.365 0.302,0.229 10 false *a 4.938,0.958 5.542,1.167 0.604,0.208 10 false CANH*b 3.354,0.625 3.76,0.792 0.406,0.167 10 false F164 4.938,1.74 5.542,1.948 0.604,0.208 10 false CANL*b 4.708,2.104 5.313,2.313 0.604,0.208 10 false CANL*b 4.667,0.667 5.271,0.875 0.604,0.208 10 false CANH*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F164-5 (CANH) - F164-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
F164-6 (CANH) - F164-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

14.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 6 CAN junction connector.


c.
C425651C26
1.417,0.75 1.917,1 0.5,0.25 2.323,1.75 2.677,0.969 true 2.49,1.76 2.729,1.333 true 2.656,2.615 2.313,2.01 true 2.729,2.333 2.5,2 true 2.146,1.771 2.479,0.729 true 2.375,2.76 2.167,2 true 1.948,2.76 2.031,2 true 2.01,1.74 2.385,0.396 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.479,0.792 1.875,0.958 0.396,0.167 10 false M104 2.792,1.188 3.344,1.438 0.552,0.25 10 false CANH*e 2.51,0.563 3.156,0.729 0.646,0.167 10 false CANH*c 2.344,2.833 2.99,3 0.646,0.167 10 false CANL*c 2.771,2.26 3.323,2.427 0.552,0.167 10 false CANL*e 2.719,2.563 3.271,2.729 0.552,0.167 10 false CANL*d 2.74,0.833 3.292,1.083 0.552,0.25 10 false CANH*d 2.427,0.313 3.073,0.479 0.646,0.167 10 false CANH*b 1.635,2.833 2.281,3 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU) (for TMC Made)
*c to Blind Spot Monitor Sensor LH
*d to Central Gateway ECU (Network Gateway ECU) (for TMMT Made)
*e to No. 1 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMC Made
Tester Connection Condition Specified Condition Connected to
M104-8 (CANH) - M104-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M104-9 (CANH) - M104-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH
M104-11 (CANH) - M104-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector

for TMMT Made
Tester Connection Condition Specified Condition Connected to
M104-9 (CANH) - M104-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH
M104-10 (CANH) - M104-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M104-11 (CANH) - M104-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

15.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

16.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

D

18.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
15.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C425651C19
1.417,0.75 1.917,1 0.5,0.25 2.323,1.76 2.75,1.208 true 2.635,2.344 2.313,2 true 2.323,2.635 2.031,2.01 true 2.031,1.75 2.49,0.875 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.5,0.792 1.896,0.958 0.396,0.167 10 false M104 2.781,1.052 3.427,1.219 0.646,0.167 10 false CANH*c 2.698,2.344 3.344,2.51 0.646,0.167 10 false CANL*c 2.354,2.698 3,2.865 0.646,0.167 10 false CANL*b 2.531,0.667 3.177,0.833 0.646,0.167 10 false CANH*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU) (for TMC Made)
*c to Central Gateway ECU (Network Gateway ECU) (for TMMT Made)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMC Made
Tester Connection Condition Specified Condition
M104-8 (CANH) - M104-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher

for TMMT Made
Tester Connection Condition Specified Condition
M104-10 (CANH) - M104-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

16.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C404458C57
3.313,0.188 3.813,0.438 0.5,0.25 2.25,1 2.677,1.427 true 2.25,2.083 2.688,1.646 true 3.385,1.417 2.875,0.479 true 2.583,2.333 3.021,1.656 true 2.969,2.5 3.385,1.656 true 2.583,0.708 3.01,1.417 true 4.042,1.438 4.427,0.74 true 4.042,1.646 4.531,2.344 true 4.385,1.417 4.833,1 true 4.385,1.656 4.833,2.083 true 3.719,1.417 4.24,0.417 true 3.677,1.635 4.167,2.333 true 1.688,0.896 2.604,1.094 0.917,0.198 10 false CANH*b 1.708,2 2.625,2.198 0.917,0.198 10 false CANL*b 4.896,0.906 5.813,1.104 0.917,0.198 10 false CANH*g 0.26,0.219 0.594,0.427 0.333,0.208 10 false *a 3.396,0.208 3.771,0.417 0.375,0.208 10 false F164 2.031,0.615 2.635,0.802 0.604,0.188 10 false CANH*c 2.042,2.271 2.958,2.469 0.917,0.198 10 false CANL*c 2.313,0.344 3.229,0.542 0.917,0.198 10 false CANH*d 2.458,2.5 3.375,2.698 0.917,0.198 10 false CANL*d 4.49,0.646 5.406,0.844 0.917,0.198 10 false CANH*f 4.583,2.292 5.5,2.49 0.917,0.198 10 false CANL*f 4.917,2 5.833,2.198 0.917,0.198 10 false CANL*g 4.292,0.323 5.208,0.521 0.917,0.198 10 false CANH*e 3.969,2.385 4.885,2.583 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Parking Assist ECU
(w/ Panoramic View Monitor System)
*f to No. 6 CAN Junction Connector
*g to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F164-1 (CANH) - F164-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance Warning ECU Assembly*1
F164-2 (CANH) - F164-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward Recognition Camera*2
F164-3 (CANH) - F164-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly*2
F164-4 (CANH) - F164-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Parking assist ECU*3
F164-5 (CANH) - F164-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector
F164-6 (CANH) - F164-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central Gateway ECU (Network Gateway ECU)


*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense

*3: w/ Panoramic View Monitor System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 6 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

17.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

D

18.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
17.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C404458C52
3.271,0.583 3.771,0.833 0.5,0.25 4.354,1.448 4.885,1.052 true 4.375,1.635 4.896,1.823 true 0.104,0.135 0.406,0.365 0.302,0.229 10 false *a 4.938,0.958 5.542,1.167 0.604,0.208 10 false CANH*b 3.354,0.625 3.76,0.792 0.406,0.167 10 false F164 4.938,1.74 5.542,1.948 0.604,0.208 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F164-6 (CANH) - F164-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

18.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367281C01
1.417,0.333 1.917,0.583 0.5,0.25 1.208,0.958 0.917,0.417 true 0.917,1.75 1.177,1.135 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.521,0.323 1,0.521 0.479,0.198 10 false CA1L 0.615,1.781 1.094,1.979 0.479,0.198 10 false CA1H 1.552,0.375 2.031,0.573 0.479,0.198 10 false F74
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 6 CAN junction connector.


c.
C425651C28
1.417,0.75 1.917,1 0.5,0.25 2.49,1.76 2.729,1.333 true 2.729,2.333 2.5,2 true 2.146,1.771 2.479,0.729 true 2.375,2.76 2.167,2 true 1.948,2.76 2.031,2 true 2.01,1.74 2.385,0.396 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.479,0.792 1.875,0.958 0.396,0.167 10 false M104 2.792,1.188 3.344,1.438 0.552,0.25 10 false CANH*d 2.51,0.563 3.156,0.729 0.646,0.167 10 false CANH*c 2.344,2.833 2.99,3 0.646,0.167 10 false CANL*c 2.771,2.26 3.323,2.427 0.552,0.167 10 false CANL*d 2.427,0.313 3.073,0.479 0.646,0.167 10 false CANH*b 1.635,2.833 2.281,3 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Blind Spot Monitor Sensor LH
*d to No. 1 CAN Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M104-8 (CANH) - M104-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
M104-9 (CANH) - M104-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH
M104-11 (CANH) - M104-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

20.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

21.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

D

23.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
20.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C425651C29
1.417,0.75 1.917,1 0.5,0.25 2.323,2.635 2.031,2.01 true 2.031,1.75 2.49,0.875 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.5,0.792 1.896,0.958 0.396,0.167 10 false M104 2.354,2.698 3,2.865 0.646,0.167 10 false CANL*b 2.531,0.667 3.177,0.833 0.646,0.167 10 false CANH*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M104-8 (CANH) - M104-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

21.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425889C09
3.333,1.083 3.833,1.333 0.5,0.25 3.469,1.833 4.24,1.24 true 2.667,1.583 3.042,1.844 true 2.667,1.333 3.167,1.844 true 3.292,1.823 2.667,1.083 true 3.052,2.073 2.75,2.333 true 3.188,2.073 2.833,2.583 true 3.479,2.063 4.031,2.729 true 3.313,2.073 3,2.833 true 2.521,1.781 2.927,1.885 true 2.573,2.125 2.917,2.021 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.094,1.479 3.01,1.677 0.917,0.198 10 false CANH*c 2.104,1.219 3.021,1.417 0.917,0.198 10 false CANH*d 2.094,0.969 3.01,1.167 0.917,0.198 10 false CANH*e 4.281,1.094 5.198,1.292 0.917,0.198 10 false CANH*f 3.427,1.125 4.042,1.323 0.615,0.198 10 false F177 2.208,2.313 3.125,2.51 0.917,0.198 10 false CANL*c 2.302,2.563 3.219,2.76 0.917,0.198 10 false CANL*d 2.677,2.854 3.594,3.052 0.917,0.198 10 false CANL*e 4.063,2.76 4.979,2.958 0.917,0.198 10 false CANL*f 1.958,1.688 2.875,1.885 0.917,0.198 10 false CANH*b 2,2.052 2.917,2.25 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera *d to Millimeter Wave Radar Sensor Assembly
*e to No. 6 CAN Junction Connector *f to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F177-1 (CANH) - F177-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance Warning ECU Assembly
F177-2 (CANH) - F177-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward Recognition Camera
F177-3 (CANH) - F177-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter Wave Radar Sensor Assembly
F177-4 (CANH) - F177-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector
F177-5 (CANH) - F177-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central Gateway ECU (Network Gateway ECU)


*1: w/ TOYOTA Parking Assist-sensor System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 6 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

22.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

D

23.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
22.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C423025C12
1.417,0.75 1.917,1 0.5,0.25 1.583,1.75 2.75,1.167 true 2.75,2.5 1.583,2 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.521,0.771 1.917,0.938 0.396,0.167 10 false F177 2.823,1.073 3.375,1.323 0.552,0.25 10 false CANH*b 2.823,2.406 3.375,2.573 0.552,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F177-5 (CANH) - F177-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

23.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367281C01
1.417,0.333 1.917,0.583 0.5,0.25 1.208,0.958 0.917,0.417 true 0.917,1.75 1.177,1.135 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 0.521,0.323 1,0.521 0.479,0.198 10 false CA1L 0.615,1.781 1.094,1.979 0.479,0.198 10 false CA1H 1.552,0.375 2.031,0.573 0.479,0.198 10 false F74
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F74-8 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR