Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
for M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION
for 2ZR-FXE with NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION
for 2ZR-FXE with LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR (for TMMT Made without Blind Spot Monitor System)
Check the No. 1 CAN junction connector. (for LHD)
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to Central Gateway ECU (Network Gateway ECU) | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F111-1 (CANH) | SB | Clearance Warning ECU Assembly*1
(for Bus 1) |
| F111-11 (CANL) | GR | |
| F111-2 (CANH) | R | Forward recognition camera*2
(for Bus 1) |
| F111-12 (CANL) | GR | |
| F111-3 (CANH) | G | Millimeter wave radar sensor assembly*2
(for Bus 1) |
| F111-13 (CANL) | GR | |
| F111-9 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F111-19 (CANL) | GR | |
| F111-10 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F111-20 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
Check the No. 1 CAN junction connector. (for RHD)
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to Central Gateway ECU (Network Gateway ECU) | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F164-1 (CANH) | SB | Clearance Warning ECU Assembly*1
(for Bus 1) |
| F164-7 (CANL) | GR | |
| F164-2 (CANH) | R | Forward recognition camera*2
(for Bus 1) |
| F164-8 (CANL) | GR | |
| F164-3 (CANH) | G | Millimeter wave radar sensor assembly*2
(for Bus 1) |
| F164-9 (CANL) | GR | |
| F164-5 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F164-11 (CANL) | GR | |
| F164-6 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F164-12 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
NO. 1 CAN JUNCTION CONNECTOR (for TMMT Made with Blind Spot Monitor System)
Check the No. 1 CAN junction connector. (for LHD)
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to No. 6 CAN Junction Connector | *f | to Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F111-1 (CANH) | SB | Clearance Warning ECU Assembly*1
(for Bus 1) |
| F111-11 (CANL) | GR | |
| F111-2 (CANH) | R | Forward recognition camera*2
(for Bus 1) |
| F111-12 (CANL) | GR | |
| F111-3 (CANH) | G | Millimeter wave radar sensor assembly*2
(for Bus 1) |
| F111-13 (CANL) | GR | |
| F111-9 (CANH) | B | No. 6 CAN junction connector
(for Bus 1) |
| F111-19 (CANL) | GR | |
| F111-10 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F111-20 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
Check the No. 1 CAN junction connector. (for RHD)
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to No. 6 CAN Junction Connector | *f | to Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F164-1 (CANH) | SB | Clearance Warning ECU Assembly*1
(for Bus 1) |
| F164-7 (CANL) | GR | |
| F164-2 (CANH) | R | Forward recognition camera*2
(for Bus 1) |
| F164-8 (CANL) | GR | |
| F164-3 (CANH) | G | Millimeter wave radar sensor assembly*2
(for Bus 1) |
| F164-9 (CANL) | GR | |
| F164-5 (CANH) | B | No. 6 CAN junction connector
(for Bus 1) |
| F164-11 (CANL) | GR | |
| F164-6 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F164-12 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
NO. 1 CAN JUNCTION CONNECTOR (for TMC Made)
Check the No. 1 CAN junction connector. (w/ Panoramic View Monitor System)
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly |
| *c | to Forward Recognition Camera | *d | to Millimeter Wave Radar Sensor Assembly |
| *e | to Parking Assist ECU | *f | to No. 6 CAN Junction Connector |
| *g | to Central Gateway ECU (Network Gateway ECU) | - | - |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F164-1 (CANH) | SB | Clearance Warning ECU Assembly
(for Bus 1) |
| F164-7 (CANL) | GR | |
| F164-2 (CANH) | R | Forward recognition camera
(for Bus 1) |
| F164-8 (CANL) | GR | |
| F164-3 (CANH) | G | Millimeter wave radar sensor assembly
(for Bus 1) |
| F164-9 (CANL) | GR | |
| F164-4 (CANH) | L | Parking assist ECU
(for Bus 1) |
| F164-10 (CANL) | GR | |
| F164-5 (CANH) | B | No. 6 CAN junction connector
(for Bus 1) |
| F164-11 (CANL) | GR | |
| F164-6 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F164-12 (CANL) | GR |
Check the No. 1 CAN junction connector. (w/o Panoramic View Monitor System)
Connection diagram
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera | *d | to Millimeter Wave Radar Sensor Assembly |
| *e | to No. 6 CAN Junction Connector | *f | to Central Gateway ECU (Network Gateway ECU) |
Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F177-1 (CANH) | SB | Clearance Warning ECU Assembly*1
(for Bus 1) |
| F177-12 (CANL) | GR | |
| F177-2 (CANH) | R | Forward recognition camera
(for Bus 1) |
| F177-13 (CANL) | GR | |
| F177-3 (CANH) | G | Millimeter wave radar sensor assembly
(for Bus 1) |
| F177-14 (CANL) | GR | |
| F177-4 (CANH) | B | No. 6 CAN junction connector
(for Bus 1) |
| F177-15 (CANL) | GR | |
| F177-5 (CANH) | P | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| F177-16 (CANL) | GR |
*1: w/ TOYOTA Parking Assist-sensor System
NO. 2 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 2 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to ECM |
| *c | to Brake Booster with Master Cylinder Assembly | *d | No. 6 CAN junction connector |
Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F113-4 (CANH) | GR | ECM
(for Bus 2) |
| F113-15 (CANL) | P | |
| F113-5 (CANH) | LG | Brake booster with master cylinder assembly
(for Bus 2) |
| F113-16 (CANL) | P | |
| F113-6 (CANH) | R | No. 6 CAN junction connector |
| F113-17 (CANL) | P |
NO. 2 CAN JUNCTION CONNECTOR (for RHD without LITHIUM-ION BATTERY)
Check the No. 2 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to Hybrid Vehicle Control ECU |
| *c | to Inverter with Converter Assembly | *d | to ECM |
| *e | No. 4 CAN Junction Connector | - | - |
Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F113-2 (CANH) | L | Hybrid vehicle control ECU
(for Bus 2) |
| F113-13 (CANL) | P | |
| F113-3 (CANH) | G | Inverter with converter assembly
(for Bus 2) |
| F113-14 (CANL) | P | |
| F113-4 (CANH) | GR | ECM
(for Bus 2) |
| F113-15 (CANL) | P | |
| F113-6 (CANH) | R | No. 4 CAN junction connector
(for Bus 2) |
| F113-17 (CANL) | P |
NO. 2 CAN JUNCTION CONNECTOR (for RHD with LITHIUM-ION BATTERY)
Check the No. 2 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to Hybrid Vehicle Control ECU |
| *c | to Inverter with Converter Assembly | *d | to ECM |
| *e | No. 6 CAN Junction Connector | - | - |
Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F113-2 (CANH) | L | Hybrid vehicle control ECU
(for Bus 2) |
| F113-13 (CANL) | P | |
| F113-3 (CANH) | G | Inverter with converter assembly
(for Bus 2) |
| F113-14 (CANL) | P | |
| F113-4 (CANH) | GR | ECM
(for Bus 2) |
| F113-15 (CANL) | P | |
| F113-6 (CANH) | R | No. 6 CAN junction connector
(for Bus 2) |
| F113-17 (CANL) | P |
NO. 3 CAN JUNCTION CONNECTOR
Check the No. 3 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Combination Meter Assembly |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to Headlight ECU Sub-assembly LH
(w/ Headlight ECU) |
| *e | to Air Conditioning Amplifier Assembly | *f | to Certification ECU (Smart Key ECU Assembly) |
| *g | to Central Gateway ECU (Network Gateway ECU) | *h | to DCM |
| *i | to Radio and Display Receiver Assembly
(for Radio and Display Type) |
- | - |
Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F114-1 (CANH) | V | Combination meter assembly
(for Bus 5) |
| F114-12 (CANL) | SB | |
| F114-2 (CANH) | G | Main body ECU (multiplex network body ECU)
(for Bus 5) |
| F114-13 (CANL) | SB | |
| F114-3 (CANH) | L | Headlight ECU sub-assembly LH*1
(for Bus 5) |
| F114-14 (CANL) | SB | |
| F114-4 (CANH) | P | Air conditioning amplifier assembly
(for Bus 5) |
| F114-15 (CANL) | SB | |
| F114-5 (CANH) | R | Certification ECU (smart key ECU assembly)
(for Bus 5) |
| F114-16 (CANL) | SB | |
| F114-6 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 5) |
| F114-17 (CANL) | SB | |
| F114-8 (CANH) | GR | DCM*3 |
| F114-19 (CANL) | LG | |
| F114-9 (CANH) | B | to Radio and display receiver assembly*2
(for Bus 3) |
| F114-20 (CANL) | LG | |
| F114-10 (CANH) | G | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| F114-21 (CANL) | LG | |
| F114-11 (CANH) | V | Central gateway ECU (network gateway ECU)
(for Bus 3) |
| F114-22 (CANL) | LG |
*1: for LED Headlight
*2: for Radio and Display Type
*3: for LHD
NO. 4 CAN JUNCTION CONNECTOR (for RHD with LITHIUM-ION BATTERY)
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Airbag Sensor Assembly |
| *c | to Brake Booster with Master Cylinder Assembly | *d | to Power Steering ECU Assembly |
| *e | to Steering Sensor | *f | to No. 5 CAN Junction Connector |
| *g | to No. 2 CAN junction connector | *h | Central gateway ECU (network gateway ECU) |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F115-1 (CANH) | B | Airbag sensor assembly
(for Bus 4) |
| F115-12 (CANL) | W | |
| F115-2 (CANH) | G | Brake booster with master cylinder assembly
(for Bus 4) |
| F115-13 (CANL) | W | |
| F115-3 (CANH) | P | Power steering ECU assembly
(for Bus 4) |
| F115-14 (CANL) | W | |
| F115-5 (CANH) | BE | Steering sensor
(for Bus 4) |
| F115-16 (CANL) | W | |
| F115-6 (CANH) | GR | No. 5 CAN junction connector
(for Bus 4) |
| F115-17 (CANL) | W | |
| F115-7 (CANH) | R | No. 2 CAN junction connector
(for Bus 2) |
| F115-18 (CANL) | P | |
| F115-8 (CANH) | W | Central gateway ECU (network gateway ECU)
(for Bus 2) |
| F115-19 (CANL) | P | |
| F115-9 (CANH) | LG | Brake booster with master cylinder assembly
(for Bus 2) |
| F115-20 (CANL) | P |
NO. 4 CAN JUNCTION CONNECTOR (for RHD without LITHIUM-ION BATTERY)
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Airbag Sensor Assembly |
| *c | to Brake Booster with Master Cylinder Assembly | *d | to Power Steering ECU Assembly |
| *e | to Brake Actuator Assembly | *f | to Steering Sensor |
| *g | to No. 5 CAN Junction Connector | *h | to No. 2 CAN junction connector |
| *i | Central gateway ECU (network gateway ECU) | - | - |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F115-1 (CANH) | B | Airbag sensor assembly
(for Bus 4) |
| F115-12 (CANL) | W | |
| F115-2 (CANH) | G | Brake booster with master cylinder assembly
(for Bus 4) |
| F115-13 (CANL) | W | |
| F115-3 (CANH) | P | Power steering ECU assembly
(for Bus 4) |
| F115-14 (CANL) | W | |
| F115-4 (CANH) | V | Brake Actuator Assembly |
| F115-15 (CANL) | W | |
| F115-5 (CANH) | BE | Steering sensor
(for Bus 4) |
| F115-16 (CANL) | W | |
| F115-6 (CANH) | GR | No. 5 CAN junction connector
(for Bus 4) |
| F115-17 (CANL) | W | |
| F115-7 (CANH) | R | No. 2 CAN junction connector
(for Bus 2) |
| F115-18 (CANL) | P | |
| F115-8 (CANH) | W | Central gateway ECU (network gateway ECU)
(for Bus 2) |
| F115-19 (CANL) | P | |
| F115-9 (CANH) | LG | Brake booster with master cylinder assembly
(for Bus 2) |
| F115-20 (CANL) | P |
NO. 4 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 4 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
*b | to Airbag Sensor Assembly |
| *c | to Brake Actuator Assembly | *d | to Brake Booster with Master Cylinder Assembly |
| *e | to ECM | *f | to Steering Sensor |
| *g | to Power Steering ECU Assembly | *h | to No. 5 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F116-1 (CANH) | B | Airbag sensor assembly
(for Bus 4) |
| F116-11 (CANL) | W | |
| F116-2 (CANH) | V | Brake actuator assembly
(for Bus 4) |
| F116-12 (CANL) | W | |
| F116-3 (CANH) | G | Brake booster with master cylinder assembly
(for Bus 4) |
| F116-13 (CANL) | W | |
| F116-4 (CANH) | L | ECM
(for Bus 4) |
| F116-14 (CANL) | W | |
| F116-5 (CANH) | BE | Steering sensor
(for Bus 4) |
| F116-15 (CANL) | W | |
| F116-6 (CANH) | P | Power steering ECU assembly
(for Bus 4) |
| F116-16 (CANL) | W | |
| F116-7 (CANH) | GR | No. 5 CAN junction connector
(for Bus 4) |
| F116-17 (CANL) | W |
NO. 5 CAN JUNCTION CONNECTOR (for RHD)
Check the No. 5 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to ECM |
| *e | to Hybrid Vehicle Control ECU | *f | to Brake Actuator Assembly*1 |
*1: for TMMT Made
Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F118-1 (CANH) | GR | No. 4 CAN junction connector
(for Bus 4) |
| F118-11 (CANL) | W | |
| F118-2 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 4) |
| F118-12 (CANL) | W | |
| F118-3 (CANH) | L | ECM
(for Bus 4) |
| F118-13 (CANL) | W | |
| F118-4 (CANH) | R | Hybrid vehicle control ECU
(for Bus 4) |
| F118-14 (CANL) | W | |
| F118-10 (CANH) | V | Brake actuator assembly*1
(for Bus 4) |
| F118-20 (CANL) | W |
*1: for TMMT Made
NO. 5 CAN JUNCTION CONNECTOR (for LHD)
Check the No. 5 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to No. 4 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to Hybrid Vehicle Control ECU |
| *e | to No. 6 CAN Junction Connector | *f | to Hybrid Vehicle Control ECU |
| *g | to Inverter with Converter Assembly | - | - |
Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| F124-1 (CANH) | GR | No. 4 CAN junction connector
(for Bus 4) |
| F124-12 (CANL) | W | |
| F124-2 (CANH) | B | Central gateway ECU (network gateway ECU)
(for Bus 4) |
| F124-13 (CANL) | W | |
| F124-3 (CANH) | R | Hybrid vehicle control ECU
(for Bus 4) |
| F124-14 (CANL) | W | |
| F124-7 (CANH) | R | No. 6 CAN junction connector
(for Bus 2) |
| F124-18 (CANL) | P | |
| F124-8 (CANH) | W | Central gateway ECU (network gateway ECU)
(for Bus 2) |
| F124-19 (CANL) | P | |
| F124-9 (CANH) | L | Hybrid vehicle control ECU
(for Bus 2) |
| F124-20 (CANL) | P | |
| F124-10 (CANH) | G | Inverter with converter assembly
(for Bus 2) |
| F124-21 (CANL) | P |
NO. 6 CAN JUNCTION CONNECTOR (for LHD with Blind Spot Monitor System)
Check the No. 6 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to Blind Spot Monitor Sensor LH | *d | to No. 1 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M104-9 (CANH) | G | Blind spot monitor sensor LH
(for Bus 1) |
| M104-20 (CANL) | GR | |
| M104-10 (CANH) | R | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| M104-21 (CANL) | GR | |
| M104-11 (CANH) | B | No. 1 CAN junction connector
(for Bus 1) |
| M104-22 (CANL) | GR |
NO. 6 CAN JUNCTION CONNECTOR (for RHD with Blind Spot Monitor System)
Check the No. 6 CAN junction connector.
Connection diagram
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to Blind Spot Monitor Sensor LH | *d | to No. 1 CAN Junction Connector |
Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| M104-8*1 (CANH)
M104-10*2 (CANH) |
R | Central gateway ECU (network gateway ECU)
(for Bus 1) |
| M104-19*1 (CANL)
M104-21*2 (CANL) |
GR | |
| M104-9 (CANH) | G | Blind spot monitor sensor LH
(for Bus 1) |
| M104-20 (CANL) | GR | |
| M104-11 (CANH) | B | No. 1 CAN junction connector
(for Bus 1) |
| M104-22 (CANL) | GR |
*1: for TMC Made
*2: for TMMT Made
DLC3
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F144-6 (CANH) - F144-14 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F144-6 (CANH) - F144-4 (CG) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F144-14 (CANL) - F144-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F144-6 (CANH) - F144-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F144-14 (CANL) - F144-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-14 (CA6H) - F74-5 (CA6L) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| F74-14 (CA6H) - F74-10 (GND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-5 (CA6L) - F74-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-14 (CA6H) - F74-1 (BATT) | R - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-5 (CA6L) - F74-1 (BATT) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-23 (CA1H) - F74-9 (CAXH) | R - P | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| F74-8 (CA1L) - F74-24 (CAXL) | GR - GR | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| F74-23 (CA1H) - F74-10 (GND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-8 (CA1L) - F74-10 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-23 (CA1H) - F74-1 (BATT) | R - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-8 (CA1L) - F74-1 (BATT) | GR - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-18 (CA4H) - F74-17 (CA4L) | W - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| F74-18 (CA4H) - F74-10 (GND) | W - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-17 (CA4L) - F74-10 (GND) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-18 (CA4H) - F74-1 (BATT) | W - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-17 (CA4L) - F74-1 (BATT) | P - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-6 (CA3H) - F74-19 (CAYH) | G - V | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| F74-21 (CA3L) - F74-20 (CAYL) | LG - LG | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| F74-6 (CA3H) - F74-10 (GND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-21 (CA3L) - F74-10 (GND) | LG - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-6 (CA3H) - F74-1 (BATT) | G - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-21 (CA3L) - F74-1 (BATT) | LG - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-22 (CA2H) - F74-7 (CA2L) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| F74-22 (CA2H) - F74-10 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-7 (CA2L) - F74-10 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-22 (CA2H) - F74-1 (BATT) | B - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-7 (CA2L) - F74-1 (BATT) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F74-15 (CA5H) - F74-16 (CA5L) | B - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| F74-15 (CA5H) - F74-10 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-16 (CA5L) - F74-10 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-15 (CA5H) - F74-1 (BATT) | B - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-16 (CA5L) - F74-1 (BATT) | SB - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
STEERING SENSOR
| *a | Component without harness connected
(Steering Sensor) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F69 steering sensor connector.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F69-3 (CANH) - F69-2 (CANL) | BE - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F69-3 (CANH) - F69-1 (ESS) | BE - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F69-2 (CANL) - F69-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F69-3 (CANH) - F69-5 (BAT) | BE - P | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F69-2 (CANL) - F69-5 (BAT) | W - P | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HYBRID VEHICLE CONTROL ECU (for 2ZR-FXE)
Refer to Terminals of ECU.
for NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>TERMINALS OF ECU
for LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F2 and F3 hybrid vehicle control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F3-25 (CA1H) - F3-24 (CA1L) | L - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F3-25 (CA1H) - F2-6 (E1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F3-24 (CA1L) - F2-6 (E1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F3-25 (CA1H) - F3-3 (BATT) | L - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F3-24 (CA1L) - F3-3 (BATT) | P - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F3-31 (CA3P) - F3-30 (CA3N) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F3-31 (CA3P) - F2-6 (E1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F3-30 (CA3N) - F2-6 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F3-31 (CA3P) - F3-3 (BATT) | R - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F3-30 (CA3N) - F3-3 (BATT) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HYBRID VEHICLE CONTROL ECU (for M20A-FXS)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F160 and F161 hybrid vehicle control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F160-21 (CA1H) - F160-8 (CA1L) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F160-21 (CA1H) - F161-3 (E1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F160-8 (CA1L) - F161-3 (E1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F160-21 (CA1H) - F161-27 (BATT) | L - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F160-8 (CA1L) - F161-27 (BATT) | P - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F160-7 (CA3P) - F160-20 (CA3N) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F160-7 (CA3P) - F161-3 (E1) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F160-20 (CA3N) - F161-3 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F160-7 (CA3P) - F161-27 (BATT) | R - B*1
R - Y*2 |
HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F160-20 (CA3N) - F161-27 (BATT) | W - B*1
W - Y*2 |
LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
*1: for RHD
*2: for LHD
INVERTER WITH CONVERTER ASSEMBLY (for 2ZR-FXE)
Refer to Terminals of ECU.
for NICKEL METAL HYDRIDE BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>TERMINALS OF ECU
for LITHIUM-ION BATTERY: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>TERMINALS OF ECU
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the C65 inverter with converter assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Inverter with Converter Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C65-1 (CANH) - C65-7 (CANL) | G - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| C65-1 (CANH) - C65-24 (GND1) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C65-7 (CANL) - C65-24 (GND1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C65-1 (CANH) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| C65-7 (CANL) - F144-16 (BAT) | P - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
INVERTER WITH CONVERTER ASSEMBLY (for M20A-FXS)
Refer to Terminals of ECU.
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the C98 inverter with converter assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Inverter with Converter Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C98-1 (CANH) - C98-7 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| C98-1 (CANH) - C98-24 (GND1) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C98-7 (CANL) - C98-24 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C98-1 (CANH) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| C98-7 (CANL) - F144-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM (for 2ZR-FXE)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A38 and C63 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A38-13 (CANH) - A38-26 (CANL) | GR - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A38-13 (CANH) - C63-59 (E1) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A38-26 (CANL) - C63-59 (E1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A38-13 (CANH) - A38-1 (BATT) | GR - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A38-26 (CANL) - A38-1 (BATT) | P - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C63-31 (CAN+) - C63-32 (CAN-) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| C63-31 (CAN+) - C63-59 (E1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C63-32 (CAN-) - C63-59 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| C63-31 (CAN+) - A38-1 (BATT) | L - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| C63-32 (CAN-) - A38-1 (BATT) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM (for M20A-FXS)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A96 ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A96-8 (CANH) - A96-18 (CANL) | P - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A96-8 (CANH) - A96-10 (E1) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A96-18 (CANL) - A96-10 (E1) | GL - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A96-8 (CANH) - A96-1 (BATT) | P - G | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A96-18 (CANL) - A96-1 (BATT) | GL - G | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F4 combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F4-32 (CANH) - F4-31 (CANL) | V - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| F4-32 (CANH) - F4-21 (ET) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F4-31 (CANL) - F4-21 (ET) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F4-32 (CANH) - F4-40 (B) | V - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F4-31 (CANL) - F4-40 (B) | SB - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A39 brake booster with master cylinder assembly connector.
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A39-30 (CA2H) - A39-29 (CA2L) | LG - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A39-30 (CA2H) - A39-26 (GND1) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A39-29 (CA2L) - A39-26 (GND1) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A39-30 (CA2H) - A39-52 (BS) | LG - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A39-29 (CA2L) - A39-52 (BS) | P - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A39-43 (CA1H) - A39-42 (CA1L) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A39-43 (CA1H) - A39-26 (GND1) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A39-42 (CA1L) - A39-26 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A39-43 (CA1H) - A39-52 (BS) | G - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A39-42 (CA1L) - A39-52 (BS) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F15 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F15-14 (CANH) - F15-13 (CANL) | G - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F15-14 (CANH) - F144-4 (CG) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F15-13 (CANL) - F144-4 (CG) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F15-14 (CANH) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F15-13 (CANL) - F144-16 (BAT) | SB - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F1-1 (CANH) - F1-2 (CANL) | R - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F1-1 (CANH) - F1-18 (E) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F1-2 (CANL) - F1-18 (E) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F1-1 (CANH) - F1-4 (+B) | R - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F1-2 (CANL) - F1-4 (+B) | SB - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
Refer to Terminals of ECU.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F23 and F68 power steering ECU assembly connectors.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F23-7 (CANH) - F23-8 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F23-7 (CANH) - F68-2 (PGND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F23-8 (CANL) - F68-2 (PGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F23-7 (CANH) - F68-1 (PIG) | P - B-W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F23-8 (CANL) - F68-1 (PIG) | W - B-W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F142 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F142-17 (R1) - F142-18 (R2) | SB - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F142-17 (R1) - F142-28 (E) | SB - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F142-18 (R2) - F142-28 (E) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F142-17 (R1) - F144-16 (BAT) | SB - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F142-18 (R2) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F150 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F150-26 (CANH) - F150-27 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| F150-26 (CANH) - F150-33 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F150-27 (CANL) - F150-33 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F150-26 (CANH) - F144-16 (BAT) | B - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F150-27 (CANL) - F144-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F73 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F73-11 (CANH) - F73-12 (CANL) | P - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F73-11 (CANH) - F73-4 (GND) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F73-12 (CANL) - F73-4 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F73-11 (CANH) - F73-1 (B) | P - V | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F73-12 (CANL) - F73-1 (B) | SB - V | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F131 and F129 radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F131-13 (CANH) - F131-14 (CANL) | B - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F131-13 (CANH) - F129-1 (GND1) | B - LA | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F131-14 (CANL) - F129-1 (GND1) | LG - LA | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F131-13 (CANH) - F129-4 (+B1) | B - LA-SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F131-14 (CANL) - F129-4 (+B1) | LG - LA-SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY LH (for LED Headlight)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A95*1 or A100*2 headlight ECU sub-assembly LH connector.
*1: for TMMT Made
*2: for TMC Made
Measure the resistance according to the value(s) in the table below.
| *A | for TMMT Made | *B | for TMC Made |
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly LH) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A95-24 (CANH) - A95-23 (CANL) | L - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A95-24 (CANH) - A95-12 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A95-23 (CANL) - A95-12 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A95-24 (CANH) - F144-16 (BAT) | L - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A95-23 (CANL) - F144-16 (BAT) | SB- R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A100-24 (CANH) - A100-23 (CANL) | L - SB | HIGH-level CAN bus line - LOWlevel CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A100-24 (CANH) - A100-12 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A100-23 (CANL) - A100-12 (GND) | SB - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A100-24 (CANH) - F144-16 (BAT) | L - R | HIGH-level CAN bus line - Auxiliary battery positive(+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A100-23 (CANL) - F144-16 (BAT) | SB- R | LOW-level CAN bus line - Auxiliary battery positive(+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the M62 blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M62-2 (CA1P) - M62-7 (CA1N) | G - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| M62-2 (CA1P) - M62-10 (BLGD) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M62-7 (CA1N) - M62-10 (BLGD) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M62-2 (CA1P) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M62-7 (CA1N) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| R5-5 (CA1P) - R5-11 (CA1N) | R - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| R5-5 (CA1P) - R5-10 (GND) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R5-11 (CA1N) - R5-10 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R5-5 (CA1P) - F144-16 (BAT) | R - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| R5-11 (CA1N) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A2 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A2-3 (CA2H) - A2-2 (CA2L) | G - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A2-3 (CA2H) - A2-1 (SGND) | G - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A2-2 (CA2L) - A2-1 (SGND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A2-3 (CA2H) - F144-16 (BAT) | G - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A2-2 (CA2L) - F144-16 (BAT) | GR - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY
Refer to Terminals of ECU.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the M71 and M70 brake actuator assembly connectors.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly)) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A85-12 (CANH) - A85-11 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A85-12 (CANH) - A85-2 (EGND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A85-11 (CANL) - A85-2 (EGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A85-12 (CANH) - A85-9 (BEPB) | V - G | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A85-11 (CANL) - A85-9 (BEPB) | W - G | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A84-12 (CANH) - A84-11 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A84-12 (CANH) - A84-2 (EGND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A84-11 (CANL) - A84-2 (EGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A84-12 (CANH) - A84-9 (BEPB) | V - G | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A84-11 (CANL) - A84-9 (BEPB) | W - G | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Front view of wire harness connector
(to Telematics Transceiver) |
Disconnect the F165 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F165-15 (CANP) - F165-16 (CANN) | GR - LG | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F165-15 (CANP) - F165-4 (E) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F165-16 (CANN) - F165-4 (E) | LG - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F165-15 (CANP) - F165-1 (+B) | GR - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F165-16 (CANN) - F165-1 (+B) | LG - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
BATTERY ECU ASSEMBLY (for LITHIUM-ION BATTERY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the z15 battery ECU assembly connector.
| *a | Front view of wire harness connector
(to Battery ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| z22-9 (CA2H) - z22-1 (CA2L) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| z22-9 (CA2H) - z22-10 (GND1) | R - GR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| z22-1 (CA2L) - z22-10 (GND1) | W - GR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| z22-9 (CA2H) - z22-8 (AM) | R - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| z22-1 (CA2L) - z22-8 (AM) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
PARKING ASSIST ECU (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the N63 parking assist ECU connector.
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| M116-40 (CANH) - M116-18 (CANL) | L - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| M116-40 (CANH) - M116-2 (GND1) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M116-18 (CANL) - M116-2 (GND1) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M116-40 (CANH) - M116-1 (+B) | L - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M116-18 (CANL) - M116-1 (+B) | GR - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
VEHICLE APPROACHING SPEAKER CONTROLLER
Refer to Terminals of ECU.
Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>ACOUSTIC VEHICLE ALERTING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F172 vehicle approaching speaker controller connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Vehicle Approaching Speaker Controller) |
- | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F172-3 (CANH) - F172-4 (CANL) | LG - P | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| F172-3 (CANH) - F172-6 (GND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F172-4 (CANL) - F172-6 (GND) | P - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F172-3 (CANH) - F144-16 (BAT) | LG - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F172-4 (CANL) - F144-16(BAT) | P - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |