There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher. | ·
CAN main bus lines or connector ·
Central gateway ECU (network gateway ECU) ·
ECM ·
No. 6 CAN junction connector (for TMMT Made) ·
No. 5 CAN junction connector (for LHD) ·
No. 4 CAN junction connector (for RHD) ·
No. 2 CAN junction connector |
This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.
for LHD
for RHD
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.
Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD with TMC Made | B |
| for RHD with TMMT Made | C |
A
B
C
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | to No. 6 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F124-7 (CANH) - F124-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 6 CAN junction connector |
| F124-8 (CANH) - F124-19 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 6 CAN junction connector) | C |
A
B
C
Reconnect the F124 No. 5 CAN junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-18 (CA4H) - F74-17 (CA4L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the F124 No. 5 CAN junction connector.
Disconnect the No. 6 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
| *b | to No. 2 CAN Junction Connector |
| *c | to No. 5 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| M104-1 (CANH) - M104-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| M104-2 (CANH) - M104-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 5 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 5 CAN junction connector) | B |
| NG (Line to No. 2 CAN junction connector) | C |
A
B
C
Reconnect the M104 No. 6 CAN junction connector.
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | to ECM |
| *c | to No. 6 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F113-4 (CANH) - F113-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| F113-6 (CANH) - F113-17 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 6 CAN Junction Connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 6 CAN junction connector) | B |
| NG (Line to ECM assembly) | C |
A
B
C
Reconnect the F113 No. 2 CAN junction connector.
Disconnect the A38 ECM connector. (for 2ZR-FXE)
Disconnect the A96 ECM connector. (for M20A-FXS)
| *A | for 2ZR-FXE |
| *B | for M20A-FXS |
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-13 (CANH) - A38-26 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A96-8 (CANH) - A96-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK (for 2ZR-FXE) | A |
| OK (for M20A-FXS) | B |
| NG | C |
A
B
C
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 4 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
| *b | to No. 2 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F115-7 (CANH) - F115-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| F115-8 (CANH) - F115-19 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 2 CAN junction connector) | C |
A
B
C
Reconnect the F115 No. 4 CAN junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-18 (CA4H) - F74-17 (CA4L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the F115 No. 4 CAN junction connector.
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | to ECM |
| *c | to No. 4 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F113-4 (CANH) - F113-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| F113-6 (CANH) - F113-17 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 4 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 4 CAN junction connector) | B |
| NG (Line to ECM assembly) | C |
A
B
C
Reconnect the F113 No. 2 CAN junction connector.
Disconnect the ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-13 (CANH) - A38-26 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 4 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 4 CAN Junction Connector) |
| *b | to No. 6 CAN Junction Connector |
| *c | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F115-7 (CANH) - F115-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 6 CAN junction connector |
| F115-8 (CANH) - F115-19 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 6 CAN junction connector) | C |
A
B
C
Reconnect the F115 No. 4 CAN junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-18 (CA4H) - F74-17 (CA4L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the F115 No. 4 CAN junction connector.
Disconnect the No. 6 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
| *b | to No. 2 CAN Junction Connector |
| *c | to No. 4 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| M104-1 (CANH) - M104-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| M104-2 (CANH) - M104-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 4 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 4 CAN junction connector) | B |
| NG (Line to No. 2 CAN junction connector) | C |
A
B
C
Reconnect the M104 No. 6 CAN junction connector.
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | to ECM |
| *c | to No. 6 CAN Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F113-4 (CANH) - F113-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| F113-6 (CANH) - F113-17 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 6 CAN Junction Connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 6 CAN junction connector) | B |
| NG (Line to ECM assembly) | C |
A
B
C
Reconnect the F113 No. 2 CAN junction connector.
Disconnect the A38 ECM connector. (for 2ZR-FXE)
Disconnect the A96 ECM connector. (for M20A-FXS)
| *A | for 2ZR-FXE |
| *B | for M20A-FXS |
| *a | Front view of wire harness connector
(to ECM) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-13 (CANH) - A38-26 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A96-8 (CANH) - A96-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK (for 2ZR-FXE) | A |
| OK (for M20A-FXS) | B |
| NG | C |
A
B
C