Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.01
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Hybrid vehicle control ECU

·

Central gateway ECU (network gateway ECU)

·

Inverter with converter assembly

·

ECM

·

Brake booster with master cylinder assembly

·

Battery ECU assembly

(for LITHIUM-ION BATTERY)

·

Vehicle Approaching Speaker Controller

(w/ Acoustic Vehicle Alerting System)

·

No. 5 CAN junction connector

(for LHD)

·

No. 4 CAN junction connector

(for RHD)

·

No. 2 CAN junction connector

·

No. 6 CAN junction connector

(for TMMT Made)



WIRING DIAGRAM

for LHD


C422232E03
1.469,0.729 1.979,0.927 0.51,0.198 10 false CANH 1.49,1.281 2,1.479 0.51,0.198 10 false CANL 5.313,0.646 5.823,0.844 0.51,0.198 10 false CA4H 5.313,1.188 5.823,1.385 0.51,0.198 10 false CA4L 5.958,1.021 6.469,1.219 0.51,0.198 10 false 120 Ω 5.083,1.188 5.396,1.385 0.313,0.198 10 false 17 5.083,0.646 5.396,0.844 0.313,0.198 10 false 18 4.042,1.177 4.354,1.375 0.313,0.198 10 false 19 4.052,0.646 4.365,0.844 0.313,0.198 10 false 8 2.771,1.177 3.083,1.375 0.313,0.198 10 false 21 2.75,0.656 3.063,0.854 0.313,0.198 10 false 10 1.948,1.177 2.167,1.354 0.219,0.177 10 false 7 1.927,0.646 2.24,0.844 0.313,0.198 10 false 1 1.49,2.875 2,3.073 0.51,0.198 10 false CA1H 1.51,3.417 2.021,3.615 0.51,0.198 10 false CA1L 2.802,2.802 3.115,3 0.313,0.198 10 false 9 2.76,3.333 3.073,3.531 0.313,0.198 10 false 20 1.917,3.323 2.573,3.542 0.656,0.219 10 false 24*2, 8*3 1.927,2.802 2.646,3.021 0.719,0.219 10 false 25*2, 21*3 4.083,2.792 4.302,2.969 0.219,0.177 10 false 7 4.063,3.323 4.281,3.5 0.219,0.177 10 false 18 0.333,1.656 1.229,1.844 0.896,0.188 10 false C65*2, C98*3 0.344,1.823 2.594,2.042 2.25,0.219 10 false Inverter with Converter Assembly 5.115,1.625 5.625,1.823 0.51,0.198 10 false F74 5.094,1.792 7.052,2.198 1.958,0.406 10 false Central Gateway ECU (Network Gateway ECU) 0.5,3.969 2.323,4.271 1.823,0.302 10 false Hybrid Vehicle Control ECU 0.5,3.792 1.323,3.979 0.823,0.188 10 false F3*2, F160*3 2.604,3.781 3.115,3.979 0.51,0.198 10 false F124 2.594,3.938 4.76,4.167 2.167,0.229 10 false No. 5 CAN Junction Connector 1.5,5.708 2.01,5.906 0.51,0.198 10 false CA2H 1.521,6.229 2.031,6.427 0.51,0.198 10 false CA2L 1.906,5.604 2.219,5.802 0.313,0.198 10 false 9 1.927,6.135 2.24,6.333 0.313,0.198 10 false 1 2.313,5.604 2.625,5.802 0.313,0.198 10 false *1 2.823,5.604 3.042,5.875 0.219,0.271 10 false 3 2.75,6.125 3.063,6.323 0.313,0.198 10 false 14 2.323,6.135 2.635,6.333 0.313,0.198 10 false *1 0.521,6.594 1.031,6.792 0.51,0.198 10 false z22 0.51,6.75 2.333,7.052 1.823,0.302 10 false Battery ECU Assembly*1 4.073,5.604 4.292,5.875 0.219,0.271 10 false 1 4.083,5.188 4.302,5.458 0.219,0.271 10 false 2 4.052,4.844 4.271,5.115 0.219,0.271 10 false 13 4.042,6.125 4.26,6.396 0.219,0.271 10 false 12 5.875,6.948 6.188,7.146 0.313,0.198 10 false B 5.344,6.938 5.656,7.135 0.313,0.198 10 false A 2.521,6.938 3.031,7.135 0.51,0.198 10 false M104 2.531,7.094 4.698,7.323 2.167,0.229 10 false No. 6 CAN Junction Connector 0.135,7.458 2.302,7.688 2.167,0.229 10 false *1: for LITHIUM-ION BATTERY 2.177,7.448 3.354,7.646 1.177,0.198 10 false *2: for 2ZR-FXE 3.656,7.438 4.979,7.635 1.323,0.198 10 false *3: for M20A-FXS

C440241E01
1.24,0.927 1.854,1.125 0.615,0.198 10 false CANH 1.26,1.469 1.875,1.667 0.615,0.198 10 false CANL 1.76,0.865 1.917,1.094 0.156,0.229 10 false 3 1.75,1.396 1.906,1.625 0.156,0.229 10 false 4 2.354,0.833 2.708,1.083 0.354,0.25 10 false *3 2.354,1.385 2.708,1.635 0.354,0.25 10 false *3 3.125,0.844 3.281,1.094 0.156,0.25 10 false 1 3.042,1.385 3.333,1.635 0.292,0.25 10 false 12 4.417,1.385 4.708,1.635 0.292,0.25 10 false 17 4.406,0.844 4.698,1.094 0.292,0.25 10 false 6 5.458,0.438 5.75,0.688 0.292,0.25 10 false A 6.021,0.448 6.313,0.698 0.292,0.25 10 false B 5.563,2.969 5.854,3.219 0.292,0.25 10 false 30 5.563,3.5 5.854,3.75 0.292,0.25 10 false 29 4.396,3.5 4.688,3.75 0.292,0.25 10 false 16 4.396,2.99 4.688,3.24 0.292,0.25 10 false 5 3.052,3.5 3.344,3.75 0.292,0.25 10 false 15 3.115,2.99 3.406,3.24 0.292,0.25 10 false 4 1.771,3.51 2.688,3.74 0.917,0.229 10 false 26*1, 18*2 1.75,2.99 2.667,3.219 0.917,0.229 10 false 13*1, 8*2 1.281,3.521 1.896,3.719 0.615,0.198 10 false CANL 1.271,3 1.885,3.198 0.615,0.198 10 false CANH 0.583,3.344 1.198,3.542 0.615,0.198 10 false 120 Ω 5.854,3.094 6.469,3.292 0.615,0.198 10 false CA2H 5.844,3.604 6.458,3.802 0.615,0.198 10 false CA2L 0.365,1.844 0.979,2.042 0.615,0.198 10 false F172 0.354,2 2.24,2.49 1.885,0.49 10 false Vehicle Approaching Speaker Controller*3 0.51,4.042 1.427,4.271 0.917,0.229 10 false A38*1, A96*2 0.5,4.219 1.417,4.448 0.917,0.229 10 false ECM 3.25,4 4.167,4.229 0.917,0.229 10 false F113 3.24,4.167 4.521,4.604 1.281,0.438 10 false No. 2 CAN Junction Connector 5.49,4.042 6.042,4.281 0.552,0.24 10 false A39 5.49,4.188 7.156,4.76 1.667,0.573 10 false Brake Booster with Master Cylinder Assembly 0.417,4.667 1.688,4.896 1.271,0.229 10 false *1: for 2ZR-FXE 0.417,5.042 1.688,5.271 1.271,0.229 10 false *2: for M20A-FXS 0.406,5.448 3.385,5.667 2.979,0.219 10 false *3: w/ Acoustic Vehicle Alerting System


for RHD


C366140E06
1.354,0.729 1.969,0.927 0.615,0.198 10 false CA2H 1.396,1.25 2.01,1.448 0.615,0.198 10 false CA2L 1.833,0.604 2.115,0.854 0.281,0.25 10 false 30 1.875,1.167 2.156,1.417 0.281,0.25 10 false 29 2.688,0.615 2.969,0.865 0.281,0.25 10 false 9 2.635,1.146 2.917,1.396 0.281,0.25 10 false 20 4,0.615 4.333,0.781 0.333,0.167 10 false 8 4.01,1.167 4.344,1.333 0.333,0.167 10 false 19 4,1.594 4.333,1.76 0.333,0.167 10 false 7 4,1.948 4.333,2.115 0.333,0.167 10 false 18 2.51,2.385 3.094,2.552 0.583,0.167 10 false F115 2.51,2.552 4.76,2.719 2.25,0.167 10 false No. 4 CAN Junction Connector 4.969,0.635 5.302,0.802 0.333,0.167 10 false 18 4.969,1.177 5.302,1.344 0.333,0.167 10 false 17 5.25,0.635 5.865,0.833 0.615,0.198 10 false CA4H 5.25,1.167 5.865,1.365 0.615,0.198 10 false CA4L 5.906,0.99 6.521,1.188 0.615,0.198 10 false 120 Ω 5.135,1.646 5.75,1.844 0.615,0.198 10 false F74 5.135,1.802 7.083,2.302 1.948,0.5 10 false Central Gateway ECU (Network Gateway ECU) 1.333,3.635 1.948,3.833 0.615,0.198 10 false CANH 1.365,4.167 1.979,4.365 0.615,0.198 10 false CANL 1.854,3.531 2.135,3.781 0.281,0.25 10 false 1 1.854,4.083 2.135,4.25 0.281,0.167 10 false 7 2.677,3.542 2.958,3.708 0.281,0.167 10 false 3 2.625,4.094 2.906,4.26 0.281,0.167 10 false 14 3.979,4.073 4.26,4.24 0.281,0.167 10 false 6 3.958,3.531 4.24,3.698 0.281,0.167 10 false 17 3.99,5.688 4.271,5.854 0.281,0.167 10 false 2 3.969,6.219 4.25,6.385 0.281,0.167 10 false 13 2.667,6.198 2.948,6.365 0.281,0.167 10 false 15 2.708,5.677 2.99,5.844 0.281,0.167 10 false 4 1.833,5.688 2.115,5.854 0.281,0.167 10 false 13 1.854,6.208 2.135,6.375 0.281,0.167 10 false 26 4.969,5.688 5.25,5.854 0.281,0.167 10 false 25 4.969,6.229 5.25,6.396 0.281,0.167 10 false 24 5.26,5.802 5.875,6 0.615,0.198 10 false CA1H 5.25,6.344 5.865,6.542 0.615,0.198 10 false CA1L 5.01,6.667 5.625,6.865 0.615,0.198 10 false F3 5.021,6.844 6.802,7.094 1.781,0.25 10 false Hybrid Vehicle Control ECU 2.583,6.677 3.198,6.875 0.615,0.198 10 false F113 2.583,6.844 4.5,7.094 1.917,0.25 10 false No. 2 CAN Junction Connector 1.01,6.698 1.625,6.896 0.615,0.198 10 false A38 1,6.854 1.5,7.021 0.5,0.167 10 false ECM 0.688,6.063 1.302,6.26 0.615,0.198 10 false 120 Ω 1.354,5.688 1.969,5.885 0.615,0.198 10 false CANH 1.375,6.208 1.99,6.406 0.615,0.198 10 false CANL 0.51,4.531 1.125,4.729 0.615,0.198 10 false C65 0.521,4.698 2.719,4.948 2.198,0.25 10 false Inverter with Converter Assembly 0.5,1.594 1.115,1.792 0.615,0.198 10 false A39 0.5,1.76 2.167,2.208 1.667,0.448 10 false Brake Booster with Master Cylinder Assembly 0.083,0.073 1.385,0.333 1.302,0.26 12 false for TMC Made:

C422234E02
1.667,0.594 2.281,0.792 0.615,0.198 10 false CA2H 1.688,1.115 2.302,1.313 0.615,0.198 10 false CA2L 5.49,0.479 6.104,0.677 0.615,0.198 10 false CA4H 5.49,1.01 6.104,1.208 0.615,0.198 10 false CA4L 6.125,0.854 6.74,1.052 0.615,0.198 10 false 120 Ω 5.24,0.469 5.552,0.708 0.313,0.24 10 false 18 5.25,1 5.563,1.24 0.313,0.24 10 false 17 4.052,1.01 4.365,1.25 0.313,0.24 10 false 19 4.063,0.49 4.375,0.729 0.313,0.24 10 false 8 2.74,1.01 3.052,1.25 0.313,0.24 10 false 20 2.781,0.479 3.094,0.719 0.313,0.24 10 false 9 2.104,1.021 2.417,1.26 0.313,0.24 10 false 29 2.104,0.479 2.417,0.719 0.313,0.24 10 false 30 4.073,2.083 4.385,2.323 0.313,0.24 10 false 18 4.073,2.448 4.385,2.688 0.313,0.24 10 false 7 5.344,3.219 5.656,3.458 0.313,0.24 10 false A 5.875,3.219 6.188,3.458 0.313,0.24 10 false B 5.156,1.479 5.635,1.698 0.479,0.219 10 false F74 5.146,1.656 7.104,2.104 1.958,0.448 10 false Central Gateway ECU (Network Gateway ECU) 2.531,2.875 3.01,3.094 0.479,0.219 10 false F115 2.521,3.042 4.708,3.375 2.188,0.333 10 false No. 4 CAN Junction Connector 0.656,1.479 1.135,1.698 0.479,0.219 10 false A39 0.646,1.656 2.302,2.083 1.656,0.427 10 false Brake Booster with Master Cylinder Assembly 0.052,0.042 2.625,0.281 2.573,0.24 12 false for TMMT Made:

C440242E01
0.104,0.073 2.677,0.313 2.573,0.24 12 false for TMMT Made: 1.177,1.083 1.792,1.281 0.615,0.198 10 false CA2H 1.167,1.625 1.781,1.823 0.615,0.198 10 false CA2L 0.281,2.083 0.896,2.281 0.615,0.198 10 false z22 0.271,2.26 2.021,2.49 1.75,0.229 10 false Battery ECU Assembly*1 1.688,1.021 1.875,1.271 0.188,0.25 10 false 9 1.677,1.563 1.865,1.813 0.188,0.25 10 false 1 2.135,1.021 2.427,1.292 0.292,0.271 10 false *1 2.135,1.552 2.427,1.823 0.292,0.271 10 false *1 2.781,1.01 3.073,1.281 0.292,0.271 10 false 3 2.698,1.552 2.99,1.823 0.292,0.271 10 false 14 4.104,0.5 4.396,0.771 0.292,0.271 10 false 2 4.073,1.021 4.365,1.292 0.292,0.271 10 false 13 4.094,1.76 4.385,2.031 0.292,0.271 10 false 12 4.083,2.219 4.375,2.49 0.292,0.271 10 false 1 2.583,2.667 3.198,2.865 0.615,0.198 10 false M104 2.573,2.844 4.615,3.073 2.042,0.229 10 false No. 6 CAN Junction Connector 5.344,0.177 5.635,0.448 0.292,0.271 10 false A 5.875,0.167 6.167,0.438 0.292,0.271 10 false B 5.156,1.917 7.083,2.167 1.927,0.25 10 false *1: for LITHIUM-ION BATTERY 5.167,2.323 6.354,2.552 1.188,0.229 10 false *2: for 2ZR-FXE 5.177,2.677 6.365,2.906 1.188,0.229 10 false *3: for M20A-FXS 5.167,3.125 7.125,3.521 1.958,0.396 10 false *4: w/ Acoustic Vehicle Alerting System 4.094,3.76 4.385,4.031 0.292,0.271 10 false 6 4.083,4.281 4.375,4.552 0.292,0.271 10 false 17 4.083,4.885 4.375,5.156 0.292,0.271 10 false 1 4.083,5.417 4.375,5.688 0.292,0.271 10 false 12 4.594,4.885 4.885,5.156 0.292,0.271 10 false *4 4.594,5.406 4.885,5.677 0.292,0.271 10 false *4 5.302,4.865 5.594,5.135 0.292,0.271 10 false 3 5.313,5.406 5.604,5.677 0.292,0.271 10 false 4 5.552,4.979 6.167,5.177 0.615,0.198 10 false CANH 5.552,5.51 6.167,5.708 0.615,0.198 10 false CANL 1.188,5.51 1.802,5.708 0.615,0.198 10 false CANL 1.146,4.969 1.76,5.167 0.615,0.198 10 false CANH 0.24,5.917 1.313,6.115 1.073,0.198 10 false C65*2, C98*3 0.229,6.104 2.344,6.354 2.115,0.25 10 false Inverter with Converter Assembly 5,5.896 5.615,6.094 0.615,0.198 10 false F172 5,6.073 6.844,6.448 1.844,0.375 10 false Vehicle Approaching Speaker Controller*4 5.531,7.063 6.146,7.26 0.615,0.198 10 false CA1H 5.542,7.635 6.156,7.833 0.615,0.198 10 false CA1L 5.333,8.031 6.583,8.271 1.25,0.24 10 false F3*2, F160*3 5.333,8.229 7.156,8.479 1.823,0.25 10 false Hybrid Vehicle Control ECU 2.583,8 3.833,8.24 1.25,0.24 10 false F113 2.573,8.156 4.552,8.396 1.979,0.24 10 false No. 2 CAN Junction Connector 0.406,8.01 1.656,8.25 1.25,0.24 10 false A38*2, A96*3 0.406,8.188 0.865,8.438 0.458,0.25 10 false ECM 0.552,7.344 1.167,7.583 0.615,0.24 10 false 120 Ω 1.146,6.99 1.76,7.229 0.615,0.24 10 false CANH 1.156,7.521 1.771,7.76 0.615,0.24 10 false CANL 1.667,6.979 2.594,7.219 0.927,0.24 10 false 13*2, 8*3 1.667,7.521 2.594,7.76 0.927,0.24 10 false 26*2, 18*3 2.781,4.885 3.073,5.156 0.292,0.271 10 false 3 2.719,5.417 3.01,5.688 0.292,0.271 10 false 14 1.677,5.406 1.969,5.677 0.292,0.271 10 false 7 1.667,4.875 1.958,5.146 0.292,0.271 10 false 1 2.771,6.979 3.063,7.25 0.292,0.271 10 false 4 2.729,7.521 3.021,7.792 0.292,0.271 10 false 15 4.063,7.521 4.354,7.792 0.292,0.271 10 false 13 4.083,6.979 4.375,7.25 0.292,0.271 10 false 2 4.75,6.979 5.646,7.188 0.896,0.208 10 false 25*2, 21*3 4.823,7.521 5.719,7.729 0.896,0.208 10 false 24*2, 8*3


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD with TMC Made B
for RHD with TMMT Made C



A

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)

B

7.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

C

12.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C01
3.333,1.083 3.833,1.333 0.5,0.25 4.083,1.844 4.583,1.583 true 4.5,0.583 3.729,1.844 true 4.583,0.917 3.854,1.844 true 3.969,1.844 4.583,1.25 true 3.708,2.073 4.167,3.083 true 3.844,2.073 4.5,2.917 true 4.094,2.063 4.583,2.25 true 3.969,2.063 4.583,2.583 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 4.563,0.49 5.479,0.688 0.917,0.198 10 false CANH*b 4.667,0.823 5.583,1.021 0.917,0.198 10 false CANH*c 4.667,1.156 5.583,1.354 0.917,0.198 10 false CANH*d 4.667,1.5 5.583,1.698 0.917,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F124 4.177,3.135 5.094,3.333 0.917,0.198 10 false CANL*b 4.563,2.906 5.479,3.104 0.917,0.198 10 false CANL*c 4.667,2.542 5.583,2.74 0.917,0.198 10 false CANL*d 4.667,2.219 5.583,2.417 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Hybrid Vehicle Control ECU
*e to Inverter with Converter Assembly - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F124-7 (CANH) - F124-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector
F124-8 (CANH) - F124-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F124-9 (CANH) - F124-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F124-10 (CANH) - F124-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inverter with Converter Assembly



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 6 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C07
1.417,0.75 1.917,1 0.5,0.25 2.063,1.75 2.5,1.167 true 2.5,2.5 2.052,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F124 2.583,1.052 3.229,1.219 0.646,0.167 10 false CANH*b 2.563,2.5 3.208,2.667 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-8 (CANH) - F124-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the F124 No. 5 CAN junction connector.


b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425889C01
3.333,1.083 3.833,1.333 0.5,0.25 2.594,1.677 2.938,1.865 true 2.583,1.365 3.052,1.854 true 3.208,1.875 2.688,1.063 true 2.583,2.271 2.958,2.063 true 3.094,2.073 2.646,2.552 true 3.188,2.083 2.813,2.854 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.042,1.625 2.958,1.823 0.917,0.198 10 false CANH*b 2.031,1.271 2.948,1.469 0.917,0.198 10 false CANH*c 2.135,0.979 3.052,1.177 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false M104 2.052,2.167 2.969,2.365 0.917,0.198 10 false CANL*b 2.094,2.469 3.01,2.667 0.917,0.198 10 false CANL*c 2.271,2.75 3.188,2.948 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to No. 5 CAN junction connector *d to Battery ECU Assembly
(for Lithium-ion Battery)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M104-1 (CANH) - M104-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
M104-2 (CANH) - M104-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 5 CAN junction connector
M104-3 (CANH) - M104-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Battery ECU Assembly*1


*1: for LITHIUM-ION BATTERY



Result:
Result Proceed to
OK A
NG (Line to No. 5 CAN junction connector) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425889C07
3.333,1.083 3.833,1.333 0.5,0.25 2.75,1.458 3.292,1.854 true 2.917,1.24 3.417,1.844 true 3.583,1.865 4.24,1.219 true 2.583,2.5 3.302,2.052 true 3.438,2.052 3.083,2.667 true 3.604,2.052 4.198,2.677 true 2.417,2.167 2.927,2.042 true 2.406,1.792 2.927,1.906 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.188,1.365 3.104,1.563 0.917,0.198 10 false CANH*c 2.385,1.135 3.302,1.333 0.917,0.198 10 false CANH*d 4.302,1.094 5.219,1.292 0.917,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.042,2.427 2.958,2.625 0.917,0.198 10 false CANL*c 2.615,2.698 3.531,2.896 0.917,0.198 10 false CANL*d 4.25,2.688 5.167,2.885 0.917,0.198 10 false CANL*e 1.823,1.677 2.74,1.875 0.917,0.198 10 false CANH*b 1.865,2.083 2.781,2.281 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Vehicle Approaching Speaker Controller
*c to ECM *d to Brake Booster with Master Cylinder Assembly
*e to No. 6 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-1 (CANH) - F113-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Vehicle approaching speaker controller
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
F113-5 (CANH) - F113-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly
F113-6 (CANH) - F113-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to No. 6 CAN junction connector) B
NG (Line to ECM) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - ECM)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
6.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A38 ECM connector. (for 2ZR-FXE)


b.

Disconnect the A96 ECM connector. (for M20A-FXS)


c.
C366166C08
1.417,0.75 1.917,1 0.5,0.25 1.365,1.75 0.792,1.25 true 0.75,2.49 1.375,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F113 0.208,1.135 0.854,1.302 0.646,0.167 10 false CANH*b 0.26,2.51 0.906,2.677 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for 2ZR-FXE) A
OK (for M20A-FXS) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

7.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C03
3.333,1.083 3.833,1.333 0.5,0.25 4.5,0.583 3.729,1.844 true 4.583,0.917 3.854,1.844 true 3.969,1.844 4.583,1.25 true 3.708,2.073 4.167,3.083 true 3.844,2.073 4.5,2.917 true 3.969,2.063 4.583,2.583 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 4.563,0.49 5.479,0.688 0.917,0.198 10 false CANH*b 4.667,0.823 5.583,1.021 0.917,0.198 10 false CANH*c 4.667,1.156 5.583,1.354 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F115 4.177,3.135 5.094,3.333 0.917,0.198 10 false CANL*b 4.563,2.906 5.479,3.104 0.917,0.198 10 false CANL*c 4.667,2.542 5.583,2.74 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake Booster with Master Cylinder Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-7 (CANH) - F115-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
F115-8 (CANH) - F115-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F115-9 (CANH) - F115-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

8.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

9.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
8.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C29
1.417,0.75 1.917,1 0.5,0.25 2.063,1.75 2.427,1.188 true 2.375,2.563 2.042,2.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.51,0.792 1.906,0.958 0.396,0.167 10 false F115 2.417,0.979 3.063,1.146 0.646,0.167 10 false CANH*b 2.406,2.573 3.052,2.74 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F115-8 (CANH) - F115-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

9.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F115 No. 4 CAN junction connector.


b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425889C06
3.333,1.083 3.833,1.333 0.5,0.25 3.604,1.854 4.167,1.271 true 2.667,1.583 3.042,1.844 true 2.667,1.333 3.167,1.844 true 3.292,1.823 2.667,1.083 true 3.052,2.073 2.75,2.333 true 3.188,2.073 2.833,2.583 true 3.583,2.063 3.885,2.813 true 3.313,2.073 3,2.833 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.094,1.479 3.01,1.677 0.917,0.198 10 false CANH*b 2.104,1.219 3.021,1.417 0.917,0.198 10 false CANH*c 2.094,0.969 3.01,1.167 0.917,0.198 10 false CANH*d 4.25,1.146 5.167,1.344 0.917,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.208,2.313 3.125,2.51 0.917,0.198 10 false CANL*b 2.302,2.563 3.219,2.76 0.917,0.198 10 false CANL*c 2.667,2.854 3.583,3.052 0.917,0.198 10 false CANL*d 3.698,2.896 4.615,3.094 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to Inverter with Converter Assembly *d to ECM
*e No. 4 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-2 (CANH) - F113-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid Vehicle Control ECU
F113-3 (CANH) - F113-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inverter with Converter Assembly
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
F113-6 (CANH) - F113-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 4 CAN Junction Connector



Result:
Result Proceed to
OK A
NG (Line to No. 4 CAN junction connector) B
NG (Line to ECM) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

10.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
10.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A38 ECM connector. (for 2ZR-FXE)


b.

Disconnect the A96 ECM connector. (for M20A-FXS)


c.
C425782C08
1.417,0.75 1.917,1 0.5,0.25 1.365,1.75 0.792,1.25 true 0.75,2.49 1.375,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F113 0.208,1.135 0.854,1.302 0.646,0.167 10 false CANH*b 0.26,2.51 0.906,2.677 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F113-4 (CANH) -F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for 2ZR-FXE) A
OK (for M20A-FXS) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367281C02
1.417,0.333 1.917,0.583 0.5,0.25 2.167,1.75 1.771,1.125 true 1.333,1.75 1.667,1.125 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 2.115,1.781 2.594,1.979 0.479,0.198 10 false CA4L 1.042,1.781 1.521,1.979 0.479,0.198 10 false CA4H 1.552,0.375 2.031,0.573 0.479,0.198 10 false F74
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F74-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425889C03
3.333,1.083 3.833,1.333 0.5,0.25 4.5,0.583 3.729,1.844 true 4.583,0.917 3.854,1.844 true 3.969,1.844 4.583,1.25 true 3.708,2.073 4.167,3.083 true 3.844,2.073 4.5,2.917 true 3.969,2.063 4.583,2.583 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 4.563,0.49 5.479,0.688 0.917,0.198 10 false CANH*b 4.667,0.823 5.583,1.021 0.917,0.198 10 false CANH*c 4.667,1.156 5.583,1.354 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F115 4.177,3.135 5.094,3.333 0.917,0.198 10 false CANL*b 4.563,2.906 5.479,3.104 0.917,0.198 10 false CANL*c 4.667,2.542 5.583,2.74 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake booster with master cylinder assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F115-7 (CANH) - F115-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector
F115-8 (CANH) - F115-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F115-9 (CANH) - F115-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 6 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

13.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

14.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
13.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C425782C06
1.417,0.75 1.917,1 0.5,0.25 2.063,1.75 2.5,1.167 true 2.5,2.5 2.052,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F115 2.583,1.052 3.229,1.219 0.646,0.167 10 false CANH*b 2.563,2.5 3.208,2.667 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F115-8 (CANH) - F115-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

14.CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Reconnect the F115 No. 4 CAN junction connector.


b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425889C04
3.333,1.083 3.833,1.333 0.5,0.25 2.667,1.583 2.938,1.865 true 2.667,1.25 3.083,1.865 true 3.198,1.844 2.75,0.917 true 2.75,2.333 2.958,2.063 true 3.083,2.042 2.688,2.677 true 3.219,2.063 2.729,3.021 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.083,1.5 3,1.698 0.917,0.198 10 false CANH*b 2.104,1.156 3.021,1.354 0.917,0.198 10 false CANH*c 2.188,0.823 3.104,1.021 0.917,0.198 10 false CANH*d 3.417,1.125 4.031,1.323 0.615,0.198 10 false M104 2.219,2.313 3.135,2.51 0.917,0.198 10 false CANL*b 2.167,2.625 3.083,2.823 0.917,0.198 10 false CANL*c 2.188,2.917 3.104,3.115 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to No. 4 CAN junction connector *d to Battery ECU Assembly
(for Lithium-ion Battery)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M104-1 (CANH) - M104-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
M104-2 (CANH) - M104-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 4 CAN junction connector
M104-3 (CANH) - M104-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Battery ECU Assembly*1


*1: for LITHIUM-ION BATTERY



Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to No. 4 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

15.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
15.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the M104 No. 6 CAN junction connector.


b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425889C08
3.333,1.083 3.833,1.333 0.5,0.25 3.604,1.865 4.24,1.24 true 2.667,1.583 3.042,1.844 true 2.667,1.333 3.167,1.844 true 3.292,1.823 2.667,1.083 true 3.052,2.073 2.75,2.333 true 3.188,2.073 2.833,2.583 true 3.573,2.063 4.031,2.729 true 3.313,2.073 3,2.833 true 2.521,1.781 2.927,1.885 true 2.573,2.125 2.917,2.021 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.094,1.479 3.01,1.677 0.917,0.198 10 false CANH*c 2.104,1.219 3.021,1.417 0.917,0.198 10 false CANH*d 2.094,0.969 3.01,1.167 0.917,0.198 10 false CANH*e 4.281,1.094 5.198,1.292 0.917,0.198 10 false CANH*f 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.208,2.313 3.125,2.51 0.917,0.198 10 false CANL*c 2.302,2.563 3.219,2.76 0.917,0.198 10 false CANL*d 2.677,2.854 3.594,3.052 0.917,0.198 10 false CANL*e 4.063,2.76 4.979,2.958 0.917,0.198 10 false CANL*f 1.958,1.688 2.875,1.885 0.917,0.198 10 false CANH*b 2,2.052 2.917,2.25 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Vehicle Approaching Speaker Controller
*c to Hybrid Vehicle Control ECU *d to Inverter with Converter Assembly
*e to ECM *f to No. 6 CAN junction connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-1 (CANH) - F113-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Vehicle approaching speaker controller
F113-2 (CANH) - F113-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F113-3 (CANH) - F113-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inverter with converter assembly
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
F113-6 (CANH) - F113-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 6 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to No. 6 CAN junction connector) B
NG (Line to hybrid vehicle control ECU) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

C

16.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

D

11.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
16.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A38 ECM connector. (for 2ZR-FXE)


b.

Disconnect the A96 ECM connector. (for M20A-FXS)


c.
C425782C07
1.5,0.833 2,1.083 0.5,0.25 1.396,1.76 0.792,1.229 true 1.375,1.99 0.875,2.458 true 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a 1.583,0.885 2.063,1.083 0.479,0.198 10 false F113 0.24,1.146 0.802,1.396 0.563,0.25 10 false CANH*b 0.344,2.385 0.906,2.635 0.563,0.25 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F113-4 (CANH) -F113-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for 2ZR-FXE) A
OK (for M20A-FXS) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)